Behringer ULTRA VIBRATO UV300 User manual

ULTRA VIBRATO UV300
Classic Vibrato Eects Pedal
Thank you for showing your condence in us by purchasing the BEHRINGER ULTRA VIBRATO UV300.
This high-quality eects pedal delivers the classic pitch modulation and dimensional vibrato eects
of the ‘60s and ‘70s. Its comprehensive controls allow you to tailor the UV300 performance right for
your needs.
1. Controls
(1) The MODE switch changes the functionality of the eects pedal footswitch. When set to LATCH,
the eect will be activated/deactivated by pressing the pedal once. When set to UNLATCH,
the eect will only be active if you depress the pedal. The BYPASS mode can be selected when
no vibrato eect is required. The input signal remains uneected even if the pedal is depressed.
(2) The RISE control adjusts the time needed for the eect to reach its maximum detuning.
Modulation sets in more slowly when it is turned clockwise.
(3) The RATE control determines the speed of the vibrato eect.
(4) The DEPTH control adjusts the intensity of the pitch modulation eect.
(5) The ON/BATT LED illuminates when the eect is activated. It also serves as a battery level indicator.
(6) Use the footswitch to activate/deactivate the eect.
(7) Use this ¼" TS IN connector to plug in the instrument cable.
(8) The ¼" TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery
(not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to
scratch the unit.
(1)
(8)
(5)
(4)
(7)
(6)
(2) (3)

ULTRA VIBRATO UV300
◊
◊ The UV300 has no on/o switch. As soon as you insert the plug into the in connector,
the UV300 is on. When not in use, remove the plug from the in connector. This extends
the life of the battery.
The SERIAL NUMBER is located at the underside.
2. Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories.
Do not service product yourself. Contact our qualied servicing personnel for servicing or repairs,
especially when power supply cord or plug is damaged.
3. Warranty
Please register your new BEHRINGER equipment right after your purchase by visiting
http://behringer.com and read the terms and conditions of our warranty carefully.
4. Specications
In
Connector ¼" TS
Impedance 500 kΩ
Out
Connector ¼" TS
Impedance 1 kΩ
Power Supply
9 V𝌂, 100 mA regulated
BEHRINGER PSU-SB
USA/Canada 120 V~, 60 Hz
China/Korea 220 V~, 50 Hz
U.K./Australia 240 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power connector 2 mm DC jack,
negative center
Battery 9 V type 6LR61
Power consumption 30 mA
Physical/Weight
Dimensions approx. 2 ⁄ x 2 ¾ x 4 ⁄"
(H x W x D) approx. 54 x 70 x 123 mm
Weight approx. 0.73 lbs / 0.33 kg
BEHRINGER is constantly striving to maintain the
highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing
products without prior notice. Specifications and appearance
may therefore differ from those listed or shown.
MUSIC Group accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description,
photograph, or statement contained herein. Technical specications, appearances and other information are subject to change without
notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE,TANNOY,TURBOSOUND,
TC ELECTRONIC,TC HELICON, BEHRINGER and BUGERA are trademarks or registered trademarks of MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2017 All rights reserved.