Belden Lumberg Automation 0930 DSL 700 User manual

LioN-M I/O modules
Technical Manual
0930 DSL 700 | 0930 DSL 701

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 2 of 12
0930 DSL 700
16 digital channels (p-switching),
channels can be used universally as inputs or
outputs, with rotary address switches
LioN-M I/O modules for DeviceNet

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 3 of 12
0930 DSL 701
16 digital inputs (p-switching),
with rotary address switches
LioN-M I/O modules for DeviceNet

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 4 of 12
Content
1. About this Manual 5
1.1. Explanations of symbols used 5
1.1.1 Use of notes 5
1.1.2 Use of hazard notes 5
1.2 Safety Guidelines 5
1.2.1 Certified usage 5
1.3 Qualified personnel 6
2. Directions for field installation 6
3. Pin assignment 7
3.1 Bus and System supply 7
3.2 Sensor/Actuator connection (M12 female connector, 5 poles) 7
3.3 System/Actuator connection (0930 DSL 700) 7
4. Communication with the module 8
4.1 Addressing 8
4.1.1 Rotary address switches 8
4.1.2 Setting of the module address via the network 8
4.2 Data transmission rate 8
4.3 Bit assignment 9
4.4 Supported communication modes 9
4.5 Diagnostic indication 9
5. Technical data 10
5.1 General data 10
5.2 Technical data – Bus system 10
5.3 Technical data power supply – Electronics 10
5.4 Technical data power supply – Sensors 10
5.5 Technical data power supply – Actuators 10
5.6 Technical data – Inputs 10
5.7 Technical data – Outputs 11

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 5 of 12
1. About this Manual
Please read the assembly and operating instructions
in this Manual carefully before putting the LioN-M
type module into operation. The Manual should be
stored in a place that is accessible for all users.
The texts, illustrations, diagrams and examples used
in this Manual are solely for the purpose of explain-
ing the operation and use of input/output modules
of the series type LioN-M.
Please contact us if you have any further questions
concerning installation and commissioning of the
devices. We will be happy to be of assistance to you
at any time.
Lumberg Automation – Belden Deutschland GmbH
Im Gewerbepark 2
58579 Schalksmühle
Tel. [phone] / 83-01
Fax [phone] / 83-333
[email protected]
www.lumberg-automation.com
Lumberg Automation reserves the right to alter
these technical modifications or to modify this
Manual at any time without notice.
1.1 Explanations of symbols used
1.1.1 Use of notes
Notes concerning important information are special-
ly marked. They are displayed as follows:
1.1.2 Use of hazard notes
Notes concerning hazards are marked as follows:
NOTE:
Non-compliance with precautionary measures can
result in possible damage to equipment and other
property.
DANGER:
Non-compliance with respective precautionary measu-
res will expose the user to life-threatening dangers
and health hazards.
1.2 Safety Guidelines
1.2.1 Certified usage
The devices described in this Manual are used as
decentralised input/output assemblies in a Device
Net network.
Our products have been developed, produced, test-
ed and documented in compliance with safety stan-
dards. No hazards to personnel or property are to be
anticipated under normal conditions in connection
with these products when the handling regulations
and safety instructions described here for project
planning, assembly and specified operations are
complied with.
The modules fulfill the requirements of the
EMC guideline (89/336/EWG, 93/68/EWG and
93/44/EWG)
Low-voltage Guideline (73/23/EWG)
are designed for utilization in the industrial area.
The industrial environment is characterised by the
fact that users are not directly connected with
the public low-voltage mains. Additional
measures are to be implemented for utilization in
residential quarters and in business and trade
areas.
Warning!
This installation can cause radio interference in resident
areas; the user may be asked to implement appropriate
measures.

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 6 of 12
The error-free, secure operation of the product
requires proper transport, storage, set-up and
assembly, as well as careful operation. The intended
operation of the device can only be guaranteed
when the housing is mounted in its entirety. All of
the other devices connected with this device must
fulfill the requirements contained in EN 61558-2-4
and EN 61558-2-6.
Project planning, installation, commissioning, main-
tenance and testing of the devices may not be per-
formed by anyone other than an electrician who has
successfully completed recognised training courses
and who is familiar with the safety standards of
automation technology.
The user has to comply with the safety and accident
prevention regulations that apply to the specific
activity being performed during project planning,
installation, commissioning, maintenance and test-
ing of the devices.
No cables or accessories may be installed except for
those which fulfill the requirements and regulations
governing safety, electromagnetic compatibility and,
where appropriate, terminal device equipment for
telecommunications and which correspond to the
statement of specifications. Information concerning
those cables and accessories which are authorized
for installation can either be obtained from
Lumberg Automation or are already described in
this Manual.
1.3 Qualified personnel
The personnel requirements are oriented towards
the requirements profile outlined by ZVEI and
VDMA. Only skilled electricians who are familiar
with the contents of this Manual are permitted to
install or service the products described.
These are individuals who
an assess the tasks to be performed on the basis
of their professional training, knowledge and
experience and on the basis of their knowledge
of the pertinent standards, and who can recog-
nise possible dangers.
have the same knowledge levels as those who
have completed a specialised training course,
thanks to many years of professional involvement
in a comparable area.
No modifications may be carried out on our product
hardware or software, insofar as they are not
described in the Manual, except by Lumberg
Automation personnel.
Warning!
Unqualified modifications of hardware or software or
non-compliance with the warning notices listed in this
Manual could lead to severe injury to persons or damage
to property.
Important note:
The module is equipped with a grounding sheet for the
purpose of discharging parasitic currents and/or for EMC
stability.
It is necessary that this grounding sheet is linked with the
reference earth by means of a low-impedance connection.
If the mounting surface is already grounded, the connecti-
on can be made directly via the fastening screw (not with
lateral mounting).
If the mounting surface is not already grounded, or if the
lateral mounting holes are used, a grounding strip or a
suitable PE wire is to be used!
2. Directions for field installation
The module is to be mounted on a level surface with
at least 2 screws.
Type of mounting Screw Tightening torque
flat M4 x 25/30 1,0 Nm
lateral M4 x 70/80 1,0 Nm
A washer in accordance with DIN 125 is to be provided
with all types of mounting fixtures.

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 7 of 12
3. Pin assignment
3.1 Bus and System supply (0930 DSL 700)
Bus and System/Sensor supply (0930 DSL 701)
7/8“ male/female connector,
5 poles
CAUTION, danger of destruction!
Never place the voltage supply (24 V DC) on the data
circuits (Pin 4, Pin 5).
Connection Function
0930 DSL 701
Drain
System / +24 V
Sensors
System / GND (0 V)
Sensors
Bus CAN_H
Bus CAN_L
3.2 Sensor/Actuator connection,
M12 female connector, 5 poles
Connection Pin Function
DSL 700 DSL 701
1 +24 V +24 V
I/O channels 2 In/Out B In B
30V0V
4 In/Out A In A
5 earth earth
3.3 System/Sensor/Actuator supply,
7/8“ male/female connector, 4 poles
Connection Pin Function
Actuators 1 +24 V
Sensors 2 +24 V
3 earth
Actuators/Sensors 4 GND (0 V)
IN OUT
IN OUT
Pin Connection Function
0930 DSL 700
1 Drain
2 System +24 V
3 System GND (0 V)
4 Bus CAN_H
5 Bus CAN_L

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 8 of 12
4. Communication with the module
4.1 Addressing
4.1.1 Rotary address switches
Two rotary switches, located above the 7/8“ bus con-
nections behind a clear cover, are used for direct
adjustment of the DeviceNet address (MAC_ID). The
switches for setting the tens and the ones of the
address are indicated. After selecting the address via
the rotary switches the address will be set internally
after power is applied to the module. Therefore the
power supply must be interrupted briefly if the
address is changed during power-on in order to
allow the module to adopt the new address.
4.1.2 Setting of the module address via the
network
The module address can also be set via the
DeviceNet network when the address allocation is
supported by the control unit manufacturer's config-
uration software that is used.
Precise directions regarding procedural method can
be found in the manual for your respective control
manufacturer.
4.2 Data transmission rate
The data transmission rate used is established at the
start of communication between the module with
the master, and is automatically detected (AutoBaud
Detection). The maximal supported Baud rate lies at
500 kbit/s.
The valid address range lies between 0 and 63. The
address is set to 63 when switched to a value in the range
of 64 to 98. The factory setting for the address is 63.
The rotary switches must be set to the value "99" to allow
software addressing.
The addressing range in such cases lies between 0 and 63.

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 9 of 12
Byte 0 4B 4A 3B 3A 2B 2A 1B 1A
Bit 7 6543210
Bitbelegung
Bit assignment
M12 Input
Byte 1 8B 8A 7B 7A 6B 6A 5B 5A
Byte 0 4B 4A 3B 3A 2B 2A 1B 1A
Byte 1 8B 8A 7B 7A 6B 6A 5B 5A
M12 Output
Diagnose / Diagnostic
Byte 2 S8 S7 S6 S5 S4 S3 S2 S1
S1...8: Status Buchse 1...8 / socket status 1...8
4.3 Bit assignment
The DeviceNet telegram permits transmission of a
maximum of 8 bytes (64 bits) of information data.
The information data with these modules consists of
two bytes input data and one byte output data.
The output byte contains the control values of the
individual outputs. Diagnostics are performed as col-
lective diagnostics and deposited in the input byte.
The undervoltage diagnostics of the actuator system
power supply can be switched off with the left DIP switch.
4.4 Supported communication modes
Polled I/O Message Connection
Change of State / Cyclic Message Connection
Explicit Message Connection
4.5 Diagnostic indication
LED Anzeige
Indication
Bedingung
Condition
Diagnoseanzeige
Diagnostic indication
1...8 A/B gelb Kanalstatus
yellow channel status
1...8 A/ rot Peripheriefehler
DIA red periphery fault
USgrün Sensorversorgung
green sensor power supply
ULgrün Aktorversorgung (nur 0930 DSL 700)
green actuator power supply (only 0930 DSL 700)
MS grün Modul betriebsbereit
green device is ready for operation
grün blinkend fehlerhafte Konfiguration
green blinking wrong configuration
rot nicht korrigierbarer Fehler
red unrecoverable fault
rot blinkend korrigierbarer Fehler
red blinking recoverable fault
rot/grün blinkend Selbsttest wird durchgeführt
red/green blinking self test is running
NS grün online, Kommunikation mit Steuerung
green online, communication with PLC
grün blinkend online, keine Kommunikation mit Steuerung
green blinking online, no communication with PLC
rot blinkend Time-Out mindestens einer I/O-Verbindung
red blinking time-out state of one or more I/O connections
rot Fehlerhafte Kommunikation, Bus-off Status,
redundante Mac-ID
red Failed communication device, BUS-OFF Status,
duplicate MAC-ID

NOTE!
A power pack with current regulation or an incorrect
fuse will result in the destruction of the module in the
event of reverse polarity.
5. Technical data
5.1 General data
Degree of protection IP 67
(only in locked position)
Operating temperature range -10°C / +60°C
Weight 380 g
Housing PBT
Vibration resistance oscillations 15 g / 5–500 Hz
Vibration resistance shocks 50 g / 11 ms
Torques:
Fastening screw M4 1,0 Nm
Connector M12 0,5 Nm
5.2 Technical data – Bus system
Protocol DeviceNet
Product code 36 (DSL 700); 38 (DSL 701)
Device Profil General Purpose Discrect I/O
Device Type: 07 hex
EDS file 0930DSL700.eds;
0930DSL701.eds
Data transmission rates 125 / 250 / 500 KBit/s
Module adjustment automatic adjustment of the
data transmission rate
MAC_ID switch position
Adjustment via address switch 0–63 dec
Adjustment via DeviceNet 99 dec
Default address 63 dec
Connection 7/8“ male/female connector,
5 poles; please see pin
assignment
5.3 Technical data power supply –
Electronics
Rated voltage 24 V DC
Voltage range 11–30 V DC
Power consumption 70 mA
Reverse polarity protection yes
Connection integrated in bus connections
5.4 Technical data power supply –
Sensors
Rated voltage USmin. ( USystem - 1,5 V)
Max. sensor current/channel 200 mA (at Tu30°C)
Short-circuit proof yes
Indication (US) LED green
Indication sensor short-ciricuit LED red
ndication sensor supply UsLED green
Connection 0930 DSL 700:
7/8" male/female connector,
5 poles; please see pin
assignment
0930 DSL 701:
generated by the electronics
power supply
Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 10 of 12
The reverse polarity protection only works if the actuator
system power supply is protected by a current overload
fuse (10 A, mT) and switches off no later than 10–100 ms
after a short circuit has occurred.
5.5 Technical data power supply –
Actuators (only 0930 DSL 700)
Rated voltage UL24 V
Voltage range 19–30 V DC
Power consumption (without load) 20 mA max.
Galvanic separation yes
Undervoltage threshold 17 V
Delay time
Undervoltage detection < 20 ms
Reverse polarity protection yes, antiparallel diode
(please see info)
Max. current consumption 5 A
Indication actuator supply USLED green
Connection 7/8"male connector, 3 poles
5.6 Technical data – Inputs
Input circuit Type 3 according to
IEC 61131-2
Rated input voltage 24 V DC
Input current at 24 V DC typ. 5 mA
Short-circuit proof yes
Channel type N.O. p-switching
Number of digital channels 16
Status indication LED yellow per channel
Diagnostic indication LED red per socket
Connection M12 f emale connector,
5 poles; please see pin
assignment

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 11 of 12
5.7 Technical data – Outputs
Output circuit Type 1.6 A according to
IEC 61131-2
Rated output current per channel: 1.6 A (please see Info 1)
Signal state "1" max. 1.9 A
Signal state "0" max. 1 mA (according to
specification)
Signal level of the outputs:
Signal state "1" min. (UL- 1 V)
Signal state "0" max. 2 V
Short-circuit proof yes
Max. output current per module 9.0 A (please see 2)
Overload-proof yes
Number of digital channels 16
Channel type N.O. p-switching
Status indication LED yellow per channel
Diagnostic indication LED red per channel/socket
Connection M12 female connector, 5 poles;
please see pin assignment
The outputs are able to switch currents of 1.6 A with a
frequency of 3 Hz with inductive loads of the
utilization category DC13 (EN60947-5-1).
Info 1: Actuator short circuits/overloads are displayed by
the channel-related error LED.
Info 2: Test proven and approved under the following
conditions:
looped through System/Sensor power supply max. 2.5 A
Power supply cable STL 204 (5 x 1 mm²)
Operating temperature range max. 40°C
max. output current 12 A

Technical Manual
0930 DSL 700 | 0930 DSL 701
Version 2.10 / 2007-Sept-03
Specifications subject to alteration! Page 12 of 12
Im Gewerbepark 2
58579 Schalksmühle
GERMANY
Tel. [phone] - 83-01
Fax [phone] - 83-3 33
[email protected]
www.lumberg-automation.com
Lumberg Automation – Belden Deutschland GmbH
Lumberg Automation offers you comprehensive technical
assistance, helping you with the application of Lumberg
Automation products.
[email protected]
Lumberg Automation Support & Service