Belimo NM24A-MP Instruction Manual

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 1 / 7
Communicative damper actuator for adjusting
dampers in technical building installations
• Air damper size up to approx.2m²
• Torque motor10Nm
• Nominal voltageAC/DC24V
• Controlmodulating, communicative 2...10V
variable
• Position feedback 2...10V variable
• Conversion of sensor signals
• Communication via Belimo MP-Bus
Technical data
Electrical data Nominal voltage AC/DC24V
Nominal voltage frequency 50/60Hz
Nominal voltage range AC19.2...28.8V/DC21.6...28.8V
Power consumption in operation 3.5 W
Power consumption in rest position 1.4 W
Power consumption for wire sizing 6 VA
Connection supply / control Cable 1m, 4 x 0.75mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 10Nm
Torque variable 25%, 50%, 75% reduced
Communicative control MP-Bus
Operating range Y 2...10V
Input Impedance 100 kΩ
Operating range Y variable Start point 0.5...30 V
End point 2.5...32 V
Options positioning signal Open/close
3-point (AC only)
Modulating (DC 0...32 V)
Position feedback U 2...10V
Position feedback U note Max. 0.5 mA
Position feedback U variable Start point 0.5...8 V
End point 2.5...10 V
Position accuracy ±5%
Direction of motion motor selectable with switch 0/1
Direction of motion note Y = 0 V: At switch position 0(ccw rotation) / 1(cw
rotation)
Direction of motion variable electronically reversible
Manual override with push-button, can be locked
Angle of rotation Max.95°
Angle of rotation note can be limited on both sides with adjustable
mechanical end stops
Running time motor 150s / 90°
Running time motor variable 43...173s
Adaptation setting range manual
Adaptation setting range variable No action
Adaptation when switched on
Adaptation after pushing the gear disengagement
button
Override control MAX (maximum position) = 100%
MIN (minimum position) = 0%
ZS (intermediate position, AC only) = 50%

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 2 / 7
Override control variable MAX = (MIN + 32%)...100%
MIN = 0%...(MAX – 32%)
ZS = MIN...MAX
Sound power level, motor 35dB(A)
Mechanical interface Universal shaft clamp 8...26.7mm
Position indication Mechanically, pluggable
Safety data Protection class IEC/EN III Safety Extra-Low Voltage (SELV)
Protection class UL UL Class 2 Supply
Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA2
Enclosure ULEnclosureType2
EMC CE according to 2014/30/EU
Certification IEC/EN IEC/EN60730-1 and IEC/EN60730-2-14
Certification UL cULus according to UL60730-1A, UL60730-2-14 and
CAN/CSAE60730-1:02
Certification UL note The UL marking on the actuator depends on the
production site, the device is UL-compliant in any
case
Mode of operation Type 1
Rated impulse voltage supply / control 0.8kV
Control pollution degree 3
Ambient temperature -30...50°C
Storage temperature -40...80°C
Ambient humidity Max. 95% r.H., non-condensing
Servicing maintenance-free
Weight Weight 0.77kg
Safety notes
•The device must not be used outside the specified field of application, especially not in aircraft or in any
other airborne means of transport.
•Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or aggressive gases
interfere directly with the device and that it is ensured that the ambient conditions remain within the
thresholds according to the data sheet at any time.
•Only authorised specialists may carry out installation. All applicable legal or institutional installation
regulations must be complied during installation.
•The device may only be opened at the manufacturer's site. It does not contain any parts that can be
replaced or repaired by the user.
•Cables must not be removed from the device.
•To calculate the torque required, the specifications supplied by the damper manufacturers concerning
the cross-section, the design, the installation site and the ventilation conditions must be observed.
•The device contains electrical and electronic components and must not be disposed of as household
refuse. All locally valid regulations and requirements must be observed.
Product features
Conventional operation:
The actuator is connected with a standard modulating signal of 0...10 V and drives to the position defined
by the positioning signal. The measuring voltage U serves for the electrical display of the actuator position
0.5...100% and as slave control signal for other actuators.
Operation on Bus:
The actuator receives its digital positioning signal from the higher level controller via the MP-Bus and
drives to the position defined. Connection U serves as communication interface and does not supply an
analogue measuring voltage.
Mode of operation

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 3 / 7
Connection option for a sensor (passive or active sensor or switching contact). The MP actuator serves as
an analogue/digital converter for the transmission of the sensor signal via MP-Bus to the higher level
system.
The factory settings cover the most common applications. Single parameters can be modified with the
Belimo Service Tools MFT-P or ZTH EU.
Simple direct mounting on the damper shaft with a universal shaft clamp, supplied with an anti-rotation
device to prevent the actuator from rotating.
Manual override with push-button possible (the gear is disengaged for as long as the button is pressed or
remains locked).
Adjustable angle of rotation with mechanical end stops.
The actuator is overload protected, requires no limit switches and automatically stops when the end stop
is reached.
The first time the supply voltage is switched on, i.e. at the time of commissioning, the actuator carries out
a synchronisation. The synchronisation is in the home position (0%).
The actuator then moves into the position defined by the positioning signal.
An adaption can be triggered manually by pressing the "Adaption" button or with the PC-Tool. Both
mechanical end stops are detected during the adaption (entire setting range).
Automatic synchronisation after pressing the gearbox disengagement button is configured. The
synchronisation is in the home position (0%).
The actuator then moves into the position defined by the positioning signal.
A range of settings can be adapted using the PC-Tool (see MFT-P documentation)
Accessories
Gateways Description Type
Gateway MP zu BACnet MS/TP UK24BAC
Gateway MP to KNX UK24EIB
Gateway MP to Modbus RTU UK24MOD
Electrical accessories Description Type
Positioner for wall mounting CRP24-B1
EXT-WR-FP20-MP
Feedback potentiometer 10 kΩ add-on P10000A
Feedback potentiometer 1 kΩ add-on P1000A
Feedback potentiometer 140 Ω add-on P140A
Feedback potentiometer 200 Ω add-on P200A
Feedback potentiometer 2.8 kΩ add-on P2800A
Feedback potentiometer 5 kΩ add-on P5000A
Feedback potentiometer 500 Ω add-on P500A
Auxiliary switch 1 x SPDT add-on S1A
Auxiliary switch 2 x SPDT add-on S2A
Positioner for wall mounting SGA24
Positioner for built-in mounting SGE24
Positioner for front-panel mounting SGF24
Signal converter voltage/current 100 kΩ Supply AC/DC 24 V Z-UIC
Connection cable 5 m, A: RJ11 6/4 ZTH EU, B: 6-pin for connection to service socket ZK1-GEN
Connection cable 5 m, A: RJ11 6/4 ZTH EU, B: free wire end for connection to MP/
PP terminal
ZK2-GEN
MP-Bus power supply for MP actuators ZN230-24MP
Mechanical accessories Description Type
Angle of rotation limiter for K-NA and K-SA 20334-00001
Actuator arm for standard shaft clamp (one-sided) AH-25
Shaft extension 240 mm Ø20 mm for damper shaft Ø 8...22.7 mm AV8-25
Shaft clamp one-sided, clamping range Ø8...26 mm with insert, Multipack 20 pcs. K-ENMA
Shaft clamp one-sided, clamping range Ø8...26 mm, Multipack 20 pcs. K-ENSA
Converter for sensors
Configurable actuators
Simple direct mounting
Manual override
Adjustable angle of rotation
High functional reliability
Home position
Adaptation and synchronisation

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 4 / 7
Shaft clamp reversible, clamping range Ø8...20 mm K-NA
Ball joint suitable for damper crank arm KH8 / KH10 KG10A
Ball joint suitable for damper crank arm KH8 KG8
Damper crank arm Slot width 8.2 mm, clamping range Ø10...18 mm KH8
Anti-rotation mechanism 180 mm, Multipack 20 pcs. Z-ARS180
Base plate extension for NM..A to NM.., pcs. Z-NMA
Position indicator, Multipack 20 pcs. Z-PI
Form fit insert 10x10mm, Multipack 20 pcs. ZF10-NSA
Form fit insert 12x12mm, Multipack 20 pcs. ZF12-NSA
Form fit insert 15x15 mm, Multipack 20 pcs. ZF15-NSA
Form fit insert 16x16mm, Multipack 20 pcs. ZF16-NSA
Form fit insert 8x8mm, Multipack 20 pcs. ZF8-NMA
Mounting kit for linkage operation for flat installation ZG-NMA
Service tools Description Type
Adapter for Service-Tool ZTH MFT-C
Belimo PC-Tool, Software for adjustments and diagnostics MFT-P
Service Tool, with ZIP-USB function, for configurable and communicative Belimo
actuators, VAV controller and HVAC performance devices
ZTH EU
Electrical installation
Supply from isolating transformer.
Parallel connection of other actuators possible. Observe the performance data.
Wiring diagrams
AC/DC 24 V, modulating Operation on the MP-Bus
Cable colours:
1 = black
2 = red
3 = white
5 = orange
Cable colours:
1 = black
2 = red
3 = white
5 = orange
Functions
Functions when operated on MP-Bus
Connection on the MP-Bus MP-Bus Network topology
A) additional MP-Bus nodes (max. 8)
There are no restrictions for the
network topology (star, ring, tree or
mixed forms are permitted).
Supply and communication in one
and the same 3-wire cable
• no shielding or twisting necessary
• no terminating resistors required

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 5 / 7
Connection of active sensors Connection of external switching contact
A) additional MP-Bus nodes (max. 8)
• Supply AC/DC 24 V
• Output signal DC 0...10 V
 (max. DC 0...32 V)
• Resolution 30 mV
A) additional MP-Bus nodes (max. 8)
• Switching current 16 mA @ 24 V
• Start point of the operating range
must be parametrised on the MP
actuator as ≥0.5 V
Connection of passive sensors
A) additional MP-Bus nodes (max. 8)
1) Depending on the type
2) Resolution 1 Ohm
Functions with basic values (conventional mode)
Override control with AC 24 V with relay contacts Override control with AC 24 V with
rotary switch
Control remotely 0...100% with
positioner SG..
Minimum limit with positioner SG.. Follow-up control (position-dependent)
Control with 4...20 mA via external resistor Functional check
Caution:
The operating range must be set to
DC 2...10 V.
The 500 Ω resistor converts the
4...20 mA current signal to a voltage
signal DC 2...10 V
Procedure
1. Connect 24 V to connections 1
and 2
2. Disconnect connection 3:
– with direction of rotation 0:
Actuator rotates to the left
– with direction of rotation 1:
Actuator rotates to the right
3. Short-circuit connections 2 and 3:
– Actuator runs in opposite
direction

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 6 / 7
Functions for actuators with specific parameters (Parametrisation necessary)
Override control and limiting with AC24V with relay contacts Override control and limiting with AC 24 V with rotary switch
1) Caution: This function is only
guaranteed if the start point of the
operating range is defined as min.
0.5 V.
Control open/close Control 3-point
Operating controls and indicators
Service
The actuator can be parametrised by ZTH EU via the service socket.
For an extended parametrisation the PC tool can be connected.
Service Tools connection

Technical data sheet NM24A-MP
www.belimo.com NM24A-MP • en-gb • 2020-12-14 • Subject to change 7 / 7
Connection ZTH EU / PC-Tool
Dimensions
Dimensional drawings
Clamping range
*Option (Accessory K-NA)
*Option: Shaft clamp mounted below (accessories K-NA needed)
.
Min. 40
.
Min. 20
Further documentation
• Overview MP Cooperation Partners
• Tool connections
• Introduction to MP-Bus Technology
Application notes
• For digital control of actuators in VAV applications patent EP 3163399 must be considered.
Shaft length