Bellfires DERBY LARGE 3 PF Instructions for use

Bell•res wishes you many cosy evenings with your new Bell•res gas •re
This document is an essential part of your gas •re. Read it carefully before
installation and use of the gas •re and keep it in a safe place!
Serial number:
Production date:
"PREMIUM FIRE"
SUPPLEMENT
INSTALLATION INSTRUCTIONS &
MAINTENANCE MANUAL
DERBY LARGE 3 PF
DERBY SMALL 3 PF
TOPSHAM LARGE 3 PF
YORK LARGE 3 PF
YORK SMALL 3 PF
VIEW BELL DERBY 3 PF
VIEW BELL SMALL 3 PF
VIEW BELL TOPSHAM 3 PF
VIEW BELL YORK 3 PF
CORNER BELL DERBY 3 L/R PF
CORNER BELL SMALL 3 L/R PF
CORNER BELL TOPSHAM 3 L/R PF
CORNER BELL YORK 3 L/R PF
Gas •replace with a closed combustion system

3
English
Installation instructions
BELLFIRES GAS FIREPLACE WITH CLOSED COMBUSTION SYSTEM:
Derby Large 3 PF (Premium Fire) (DYL3 PF)
Derby Small 3 PF (Premium Fire) (DYS3 PF)
Topsham Large 3 PF (Premium Fire) (TSL3 PF)
York Large 3 PF (Premium Fire) (YKL3 PF)
York Small 3 PF (Premium Fire) (YKS3 PF)
View Bell Derby 3 PF (Premium Fire) (VWBDY3 PF)
View Bell Small 3 PF (Premium Fire) (VWBS3 PF)
View Bell Topsham 3 PF (Premium Fire) (VWBTS3 PF)
View Bell York 3 PF (Premium Fire) (VWBYK3 PF)
Corner Bell Derby 3 L/R PF (Premium Fire) (CBDY3 L/R PF)
Corner Bell Small 3 L/R PF (Premium Fire) (CBS3 L/R PF)
Corner Bell Topsham 3 L/R PF (Premium Fire) (CBTS3 L/R PF)
Corner Bell York 3 L/R PF (Premium Fire) (CBYK3 L/R PF)
IMPORTANT !
For the installation of your appliance, use both installation instructions
supplied:
1. The (basic) installation instruction, with one of the following titles:
• DERBY LARGE 3 CF/LF
• DERBY SMALL 3 CF/LF
• TOPSHAM LARGE 3 CF/LF
• YORK LARGE 3 CF/LF
• YORK SMALL 3 CF/LF
• VIEW BELL DERBY 3 CF/LF
• VIEW BELL SMALL 3 CF/LF
• VIEW BELL TOPSHAM 3 CF/LF
• VIEW BELL YORK 3 CF/LF
• CORNER BELL DERBY 3 L/R CF/LF
• CORNER BELL SMALL 3 L/R CF/LF
• CORNER BELL TOPSHAM 3 L/R CF/LF
• CORNER BELL YORK 3 L/R CF/LF
2. The “Premium Fire” installation instruction, which supplements
the above installation instructions. This installation instruction has
been supplied because the appliance has been fitted with a
“Premium Fire” double burner.

4
English
Installation instructions

5
English
Installation instructions
The installation must only be carried out by a
“Gas Safe Register” registered installation engineer.
IMPORTANT
SUPPLEMENT TO THE CONTENTS
Page
1. INSTALLATION INSTRUCTIONS ............. .... ............. .. ....... .................... .. 7
1.7.6 Placing the ceramic log set, ‘fire glass’,
embers and decorative ash ................................ .................. ......... .. 10
4A. DISASSEMBLY AND ASSEMBLY OF THE BURNERS AND
MESH GRATES
REPLACING THE AMBIENT LIGHTS ....................................................... 25
7. TECHNICAL DETAILS AND REGULATIONS .
.................... ....... ......... .... .. . 39
8. REPLACEMENT PARTS LIST .......................................................
.... .... . .. 41

6
English
Installation instructions

7
English
Installation instructions
Figure 23A: Module (Light)
The appliance is fitted with a 230V AC connection and may only be connected to an
earthed socket. The appliance has ambient lighting.
SUPPLEMENT TO CHAPTER 1: INSTALLATION INSTRUCTIONS
Page 56:
Appliance Module (light) 230V AC
Receiver 6V DC (via the Important: Do
Remote control 5-pole cable not place batteries
of the Module in the receiver!
(Light))
Hand
transmitter 1x 9V Block battery
Remote control
Electrical connections and batteries:

8
English
Installation instructions
Figure 23B: Electrical connections Receiver and Module(Light)
Upon delivery of the appliance, the electrical connections of the gas regulator block and
the receiver are already assembled.
The Module(Light) is separately delivered with the appliance. This component is to be
electrically connected during the installation according to the following Figure 23B and 23C.
Attach the earth cable (yellow/green) to a metal part on the inside
of the operating unit, with the help of the existing screw.
3 wire cable 230 VAC
Module(light) → Ambient Lamps (2x 25W)
RESET - button
Thermocouple
voltage/current
OUT - connection
(yellow)
Thermocouple
voltage/current
IN - connection
(red)
5 wire cable 6 VDC
MODULE receiver →
Module(light)
8 wire cable
6 VDC
Receiver →
Gas regulator
block
Module(light)
230 VAC
Receiver
2 wire cable 6 VDC
AUX receiver →
Gas valve
“rear burner” 230 VAC Appliance power
cable 3 wire cable
Earth cable
(yellow / green)
Attach this cable to a
metal part of the
operating unit.
Do not place
batteries in the
receiver!

9
English
Installation instructions
Figure 23C: Connecting 5 wire cable 6VDC on MODULE connection of
the receiver
Figure 23D: Built-in operating unit
Position Receiver, Module(Light) and Gas regulator block
(Components are in the picture not yet electrically connected!)
Built-in
operating unit Receiver Module(Light)
Rating
plate
Gas regulator block
Attach the Earth
cable (yellow /
green) to a
metal part on the
inside of the
operating unit.

10
English
Installation instructions
Page 64:
1.7.6 Placing the ceramic log set, ‘fire glass’, embers and decorative ash.
For appliance fitted with the "Premium Fire" (PF) double burner:
The construction of the ceramic log set, "fire glass", embers and decorative ash
for an appliance with a "Premium Fire (PF) NATURAL GAS double burner is
the same as for a Premium Fire (PF) PROPANE/BUTANE double burner.
The appliance is supplied with
• Ceramic log set ; See Log Nos. 14 to 25 below.
• "Fire glass Black"
• "Fire glass Dark Amber"
• Embers
• Decorative ash
°Ceramic log set; Logs nos. 14 to 25
°Embers; E
°Decorative ash; A

11
English
Installation instructions
• "Fire glass Black
• "Fire glass Dark Amber"
• Embers; E

12
English
Installation instructions
• Decorative ash; A
Important : • Place the log set, ‘fire glass’, embers and decorative ash,
carefully on and around the main burners, as indicated by the
specifications mentioned in this chapter.
• Do not place "fire glass", embers or decorative ash on or
against the pilot light burner.
• To prevent this, the pilot light is fitted with a pilot light cap.
Never remove this cap!
• Ensure that the pilot light is always able to burn
freely over the main burner.
Proper ignition of the main burner will only be guaranteed if this
is the case. Not adhering to these stipulations can give rise to
dangerous situations.
• Ensure that the pilot light is always easily visible.
• The burner bed (with '"fire glass", embers and decorative ash)
and the logs construction may not be changed.
• Only use materials supplied! This has been approved and the
quantity is defined per appliance.
• Replacement parts are available through your dealer.
• Placement may only be carried out by an authorised
person.
Remove the glass from the appliance, in accordance with the specifications in
Chapter 4; DISASSEMBLY / ASSEMBLY OF THE GLASS.
See (basic) installation instructions.

13
English
Installation instructions
If necessary repair the ambient lighting.
See Chapter 4A: DISASSEMBLY AND ASSEMBLY OF THE BURNERS AND
MESH GRATES - REPLACING THE AMBIENT LIGHTING.
Only use original ambient lights.
Check the operation of the ambient lighting/dimmer with the remote control.
See operating instructions; Operation light / dimmer
1.7.6.1 Ceramic log set + ‘fire glass’ + embers + decorative ash
1 IMPORTANT: Check the presence of the three burner fixing bolts.
See photo.

14
English
Installation instructions
2 Place burner log No. 16 carefully on the burner - right.
Check first if the "Arrow", on the underside of the log, is pointing up.
Check that the underside of the log has free space on both end faces of ± 5 mm
with respect to the metal burner.
Burner log No. 16 =
Art. no. 340021 (legible on
the underside of the log)
Underside
of log
Underside
± 5 mm
Burner
± 5 mm
Underside
of log
Underside
Burner

15
English
Installation instructions
3 Place burner log No. 14 carefully on the burner - left.
Check first if the "Arrow", on the underside of the log, is pointing up.
Burner log No. 14
Art. no. 340019 (legible on
the underside of the log)
Check that the underside of the log has free space on both end faces of ± 5 mm
with respect to the metal burner.
Underside
of log
Underside
± 5 mm
Burner
± 5 mm
Underside
of log
Underside
Burner

16
English
Installation instructions
4 Place burner log No. 15 carefully on the burner - middle (with the pilot light).
Burner log No. 15 = Art. no. 340020 (legible on the underside of the log)
Check that the pilot light remains visible.

17
English
Installation instructions
5 Place the charcoal part No. 23 (= 1x Art. no. 340028) under the Right burner,
around the venturi.
6 Place the charcoal part No. 24 (= 1x Art. no. 340029) under the Left burner,
around the venturi.

18
English
Installation instructions
8 Sprinkle the ‘Fire glass Black’ evenly on the grate, left and right of the
mesh grate.
7 Sprinkle the ‘Fire glass Dark Amber’ evenly on the mesh grate, around the
burners.
Note: Put no "fire glass" on or against the pilot light burner!
Note: Put no ‘fire glass’ under burner logs No. 14, 15 and 16, where these
are supported by the mesh grate.
Note!
Do not sprinkle "Fire glass Black"
on the mesh grate, around
the burners.
‘Fire glass Black’ blocks the
light too much.

19
English
Installation instructions
9 Set the light intensity of the ambient lighting/dimmer to max. on the remote control.
See operating instructions; Operation light / dimmer
Check that the "fire glass" is distributed evenly and that the light intensity is the
same everywhere. Adjust the distribution of the "fire glass" if necessary.
10 Place log No. 18 (= 1x Art. no. 340023).

20
English
Installation instructions
11 Place charcoal part No. 21 (= 1x Art. no. 340026).
12 Place log No. 17 (= 1x Art. no. 340022).
13 Place branch No. 19 (= 1x Art. no. 340024).