Belmont EURUS SWIVEL CHAIR User manual

EURUS SWIVEL CHAIR
INSTALLATION INSTRUCTIONS

2
1 Safety Consideration
2 Cautions regarding installation
1-1 Risk Level Interpretation ............................................................ 3
1-2 Safety Precautions ..................................................................... 5
2-1 Precautions for installation ..........................................................6
3 Installation
3-1 Dimensions/Environmental Requirements ...................................7
3-1-1 Dimensions ..............................................................7
3-1-2 Environmental Requirements ....................................8
3-2 Necessary tools and supplied parts ............................................8
3-2-1 Necessary tools ........................................................8
3-2-2 Supplied parts ..........................................................9
3-3 Installation procedures .............................................................10
3-3-1 When the chair is not upholstered ..........................10
3-3-2 When the chair is upholstered ................................14
Table of Contents
4 Flow Diagram/Wiring Diagram
4-1 Flow Diagram ...........................................................................16
4-2 Wiring Diagram .........................................................................18
2019-04 (2nd Edition)
REF 1E079PBE

3
1 Safety Consideration
1-1 Risk Level Interpretation
CONTRAINDICATION
Precautions before use
Classification by degree of
harm or damage and urgency
Make sure to carefully read the Safety Precautions and Operat-
ing Precautions and use the product correctly.
Use of the product without regard to this indication will create
a hazardous condition that may result in death or serious
injury.
Improper handling of the product without regard to this
indication will create a hazardous condition that may result in
death or serious injury.
Improper handling of the product without regard to this
indication will create a potentially hazardous condition that
may result in moderate or slight injury or property damage.
These precautions are intended to ensure the safe use of the
product and prevent harm or damage to users or other people.
According to the magnitude of harm and damage and the degree
of urgency, an incident that may be caused by misuse of the
product is classified into one of the following categories:
CONTRAINDICATION, WARNING, and CAUTION.
All of these categories are important for safety. Always follow the
instructions provided.
We assume no responsibility for any accident due to failure to
follow the Safety Precautions even in the event of harm or damage
to users or other persons.
In such case, users or other persons who use the product without
observing the Safety Precautions is responsible for any harm or
damage incurred.
The graphical symbols are explained in detail below.
Once you have fully understood this explanation, read the text.
WARNING
CAUTION

4
1 Safety Consideration
The following graphical symbols are used to explain your
responsibilities for using the product safely:
Generally prohibited activity
Disassembly, repair or modification prohibited
Mandatory instructions for ordinary users
Graphical symbols for prohibited activity
Graphical symbol for mandatory instructions

5
1 Safety Consideration
Precautions regarding installation
Do not install the product near electromagnetic sources such as
communication facilities or elevators.
Malfunction of this product may occur in the presence of
electromagnetic interference waves.
Installing or transferring the
product
Precautions for installation
Make sure to place the product on a firm and flat floor.
Placing the equipment on a tilted floor (≥ 5°) may cause it to fall.
To avoid the risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
Failure or electric leak may result in electric shock.
Precautions for operating the chair
Before and during the chair operation, pay close attention to the
operation range (seat raising/lowering direction, backrest
lowering/raising direction, and legrest traveling direction, and
ensure that the chair does not contact any body parts,hands or
feet, or objects. Body parts, hands or feet, or objects may
become caught in the chair, causing injury or damage to periph-
eral devices.

Installing or transferring the
product
Installation
Installation Cautions on Installation Work
Metal or mechanical parts of this product may have sharp edges
or corners. Be careful to avoid injury to your hands and fingers
during installation work.
1-2 Safety Precautions
CONTRAINDICATION
WARNING
CAUTION

6
2-1 Precautions for installation
1. While carrying the chair, make sure to hold only the
designated parts. If not, it may lead to physical injury.
2. Confirm that the fixing bolts are tightened before carrying the
chair.
3. Take care not to topple the equipment during transportation.
4. Do not drop, hit, or give a shock to the product.
5. Do not connect a power supply other than the rated voltage.
6. Make sure to connect ground wires.
7. When all the installation procedures have been completed,
verify that each function works properly.
2 Cautions regarding installation

7
3 Installation
AC-ERS-FD＊
AC-ERS-FP＊
100
80°
565610
480 〜725
(510 〜755)
1130 〜1375
18°
18°
180
°2
1765
670
210
585
580
485
190
105°
105°
100
80°
565545
480 〜725
(510 〜755)
1125 〜1370
18°
18°
120
°2
1700
685
210
580
190
105°
105°
35°
585
485
Unit: mm (Dimensional tolerance:±10%)
*1 ( ) : Flat seat
*2 Dimensions and specifications are subject
to change without notice.
3-1 Dimensions/Environmental Requirements
3-1-1 Dimensions
*1*1

8
3 Installation
3-1-2 Environmental Requirements
3-2 Necessary tools and supplied parts
3-2-1 Necessary tools
The table below shows the necessary tools for the installation of
this product.
Usage environment Temperature 0°C to 40°C
Humidity 10% to 95%
Atmospheric pressure 700 to 1060 hPa
Transportation/storage Temperature −20°C to 70°C
environment Humidity 10% to 95%
Atmospheric pressure 700 to 1060 hPa
No.
1
2
3
4
5
Tool name
Phillips screwdriver No. 1–3
Monkey wrench (Max. opening width: 29 mm)
6-piece double head open end wrench set (5.5–24 mm)
8-piece hex key wrench set (1.5–8 mm)
Level
QTY.
1 for each
1
1
1
1

9
3 Installation
3-2-2 Supplied parts
The table below shows the supplied parts included in the chair.
Chair (unit)
1
2
3
4
5
6
7
8
No.
Bolt cap
Hex head flange screw TP-A, M8 × 30, black
Countersunk screw, M5 × 8, plated
Truss head screw M4 × 6, plated
Truss head screw, M5 × 8, chrome-plated
Headrest unit (manual headrest only)
Headrest cover
Backrest cover
Part name QTY.
4
4
3
6
4
1
1
1
*
*
*
*
*
*
*
*
*
*
1
2
3
4
5
No.
Seat
Backrest
Headrest
Roll-up legrest
Roll-up legrest cover
Part name QTY.
1
1
1
1
1
Chair (cover parts)
* When the chair is shipped upholstered, these parts are incorporated in the products.

10
3 Installation
3-3 Installation procedures
1. Unpack the carton of the chair.
Remove TP-A, M4 × 35, plated (10 pieces) for packing.
2. Remove the chair from the skid.
Remove the hex coach bolts, M6 × 50, plated (4 pieces) that
fix the base and skid.
3. Place the chair at the approximate location.
By holding the carriage bar, bring up the chair to move it out of
the skid.
4. Remove the carriage bar by unscrewing hex bolts,
M8 × 95, plated (4 pieces).
5. Remove the fixing bolts.
Remove the hex bolt, M10 × 120, plated (1 piece).
3-3-1 When the chair is not upholstered

11
3 Installation
6. Attach the headrest.
For the manual headrest :
(1) Attach the headrest to the headrest unit.
Fix the headrest with the countersunk screws, M5 × 8,
plated (3 pieces).
(2) Attach the headrest cover.
Insert the catch of the headrest cover to the headrest.
For the power headrest :
(1) Insert the headrest cover to the headrest bar.
(2) Attach the headrest to the headrest unit.
Fix the headrest with the countersunk screws, M5 × 8,
plated (3 pieces).
(3) Attach the headrest cover.
Insert the catch of the headrest cover to the headrest.
7. Attach the backrest.
Fix the backrest with truss head screws, M5 × 8, chrome-
plated (4 pieces).
8. Attach the backrest cover.
Insert the catch of the backrest cover to the backrest.

12
3 Installation
9. Attach the upholstery of roll-up.
(1) Operate automatic operation 1 to raise the legrest.
(2) Insert the belt of upholstery between roller and frame.
(3) Pull out the belt of upholstery from frame of legrest.
(4) Fold the belt of upholstery.
Attach the belt of upholstery with truss head screw,
M4 × 6, plated (1 piece).
*Attach the opposite side of belt as well in procedure (2) - (4).
(5) Attach the upholstery along on the roller.
Fix the upholstery with truss head screws, M4 × 6, plated
(4 pieces).

13
3 Installation
(6) Attach the roll-up cover with hook and loop fastener.
(7) Attach the roll-up cover with hook and loop fastener on the
back side of legrest.
10. Attach the seat
11. Fix the chair to the floor.
Use hex head flange screws, TP-A M8 × 30, black (4 pieces).
12. Put the bolt caps (4 pieces) to the bolts attached in
Procedure 11.

14
3 Installation
1. Unpack the carton of the chair.
Remove TP-A, M4 × 35, plated (10 pieces) for packing.
2. Remove the chair from the skid.
Remove the hex coach bolts, M6 × 50, plated (4 pieces) that
fix the base and skid.
3. Place the chair at the approximate location.
By holding the carriage bar, bring up the chair to move it out of
the skid.
4. Remove the carriage bar by unscrewing hex bolts,
M8 × 95, plated (4 pieces).
5. Remove the fixing bolts.
Remove the hex bolt, M10 × 120, plated (1 piece).
3-3-2 When the chair is upholstered

15
3 Installation
6. Attach the seat
7. Fix the chair to the floor.
Use hex head flange screws, TP-A M8 × 30, black (4 pieces).
8. Put the bolt caps (4 pieces) to the bolts attached in
Procedure 7.

16
4 Flow Diagram/Wiring Diagram
4-1 Flow Diagram
Manual Headrest
HYRON HOSE AENL81**
HYRON HOSE AENL72**
HYRON HOSE AENL83**
HYRON HOSE AENL83**
HYRON HOSE AENL70**
REC CYL ASSY AXBA30**
LEGREST CYL AXBA31**
FOOT REST CYL AXBA32**
LIFT CYL ASSY 1G072N**
OIL TANK
P
A
Footrest shorten
Legrest down
Chair down
Backrest recline
B C D
R
MOTOR
VOLTAGE 8SOLENOID VALVE CODE 100V 50/60Hz,110V60Hz 1G07DG** 110 50Hz,115V 50/60Hz,120V 60Hz 1G07DH** 220V 50/60Hz,230V 60Hz 1G07DJ** 230V 50Hz,240V 50/60Hz 1G07DK**
VOLTAGE MOTOR CODE CONDENSER CODE 100V ANDS56** AATP22** 110-120V ANDS56** AATP26** 220-240V ANER60** AATP27**
Footrest extend Not Adjustable
Legrest up Not Adjustable
Chair up Not Adjustable
Backrest raise Not Adjustable
High pressure hose Low pressure hose Low pressure hose

17
4 Flow Diagram/Wiring Diagram
Power Headrest
HYRON HOSE AENL70**
HYRON HOSE AEFS04**
HYRON HOSE AEFR94**
HYRON HOSE AEFS01**
PH ANGLE CYL AZDJ05**
PH LIFT CYL AZDJ06**
HYRON HOSE AENL81**
HYRON HOSE AENL83**
HYRON HOSE AENL83**
HYRON HOSE AENL70**
REC CYL ASSY AXBA30**
LEGREST CYL AXBA31**
FOOT REST CYL AXBA32**
LIFT CYL ASSY 1G07BK**
HYRON TUBE X-55130
HYRON TUBE X-55130
OIL TANK
MOTOR
P
A
Footrest shorten
Legrest down
HR recline
HR down
Chair down
Backrest recline
B C D
R
P
A B
R
VOLTAGE 4SOLENOID VALVE CODE 100V 50/60Hz,110V60Hz 1G07DC** 110 50Hz,115V 50/60Hz,120V 60Hz 1G07DD** 220V 50/60Hz,230V 60Hz 1G07DE** 230V 50Hz,240V 50/60Hz 1G07DF**
VOLTAGE MOTOR CODE CONDENSER CODE 100V ANDS56** AATP22** 110-120V ANDS56** AATP26** 220-240V ANER60** AATP27**
VOLTAGE 8SOLENOID VALVE CODE 100V 50/60Hz,110V60Hz 1G07DG** 110 50Hz,115V 50/60Hz,120V 60Hz 1G07DH** 220V 50/60Hz,230V 60Hz 1G07DJ** 230V 50Hz,240V 50/60Hz 1G07DK**
Footrest extend Not Adjustable
Legrest up Not Adjustable
Chair up Not Adjustable
Backrest raise Not Adjustable
HR raise Not Adjustable
HR up Not Adjustable
High pressure hose Low pressure hose Low pressure hose

18
4 Flow Diagram/Wiring Diagram
4-2 Wiring Diagram
Manual Headrest
LED4 Light on when all function is locked
LED5 Light on when limit mode
LED6 Light on when power is on
JP1 Voltage selection
SW4-1 On when power headrest is functioned
TL TERMINAL A
100V 1A0RF0**
200V 1A0RL4**
TL TERMINAL B
1A0RF1**
TL NOISE FILTER A
1A0RF2**
Purple Grey
TL LEGREST SAFE SW
1A0RJL**
TL LEGPARTS
1A0PBF**
4
BACK POTENTIO METER L 1A0PBD**
LEG POTENTIO METER L 1A0PBG**
SEAT POTENTIO METER L 1A0PBC**
DUMMY BACKSAFE SW
1A0PUG**
DUMMY ARM SAFE SW
1A0PU1**
8 9
Brown Red
Brown Red
Orange Brown Red Orange
10
Brown Red Orange
ROLL POTENTIO METER L 1A0PBH**
11
Brown Red Orange Brown Red Orange
Yellow Green Blue
Brown
Red
Yellow
Yellow
Yellow
Yellow
Red
Brown/White
Yellow
White
TL FOR CONDENSER
ANDS55**
MOTOR CONDENSER
CHAIR SV
Brown
SV1 SV2
SV7 SV8
SV5 SV6 SV3 SV4
Red Brown Red Orange
Yellow
Green Pink Blue Sky Blue Purple Black Yellow Orange Grey White
CHAIR CONTROL PCB L
100V:1G07NG** 200V:1G07NH**
TL OILMOTOR
1A0P9D**
VOLTAGE MOTOR CODE CONDENSER CODE
100V ANDS56** AATP22**
110-120V ANET56** AATP26**
220-240V ANER60** AATP27**
Brown
Brown
Blue
Blue
TL NOISE FILTER B
BREAKER 5A
EARTH WIRE
1A0H0W**
1A0RF3**
TL SLDVALVE CHAIR
1A0P9E**
TL SLDVALVE RLL
1A0P9F**
23
Brown Blue
Yellow Green
Yellow Green
Brown Blue
Yellow Green
Brown Blue
PLUG TYPE CODE
A TYPE 1A0RJJ**
C TYPE 1A0RF4**
BF TYPE 1A0RJH**
AUSTRALIA 1A0RL2**
N L
Noise Filter
Orange
TL STICK SW(A-M)
1A0S3T**
2
Brown Red Orange Yeloow Green Blue Purple Grey Black
Brown Red Orange Yellow Green
Brown Red Orange
Yellow
Green
Brown Red Orange Yellow Green
TL STICK SW(047) 1A0RKS** TL STICK SW(047) 1A0RKS**
Brown Red Orange
Yellow
Green
TL STICK SW(047) 1A0RKS**
TL BRANCH STICK
1A0RGA**
STICK SWITCH PCB
1G01Q1**
STICK SWITCH PCB
1G01Q1**
Manual
STICK SWITCH PCB
1G01Q1**
ManualAuto
VOLTAGE 8SOLENOID VALVE CODE
100V 50/60Hz,110V 60Hz 1G07DG**
110V 50Hz,115V 50/60Hz,120V 60Hz 1G07DH**
220V 50/60Hz,230V 60Hz 1G07DJ**
230V 50Hz,240V 50/60Hz 1G07DK**

19
4 Flow Diagram/Wiring Diagram
Power Headrest
LED4 Light on when all function is locked
LED5 Light on when limit mode
LED6 Light on when power is on
JP1 Voltage selection
SW4-1 On when power headrest is functioned
TL TERMINAL A
100V 1A0RF0**
200V 1A0RL4**
TL TERMINAL B
1A0RF1**
TL NOISE FILTER A
1A0RF2**
Purple Grey
TL LEGREST SAFE SW
1A0RJL**
TL LEGPARTS
1A0PBF**
4
BACK POTENTIO METER L 1A0PBD**
LEG POTENTIO METER L 1A0PBG**
SEAT POTENTIO METER L 1A0PBC**
DUMMY BACKSAFE SW
1A0PUG**
DUMMY ARM SAFE SW
1A0PU1**
8 9
Brown Red
Brown Red
Orange Brown Red Orange
10
Brown Red Orange
ROLL POTENTIO METER L 1A0PBH**
11
Brown Red Orange Brown Red Orange
Yellow Green Blue
Brown
Red
Yellow
Yellow
Yellow
Yellow
Red
Brown/White
Yellow
White
TL FOR CONDENSER
ANDS55**
MOTOR CONDENSER
CHAIR SV
Brown
SV1 SV2
SV7 SV8
SV5 SV6 SV3 SV4
Red Brown Red Orange
Yellow
Green Pink Blue Sky Blue Purple Black Yellow Orange Grey White
CHAIR CONTROL PCB L
100V:1G07NG** 200V:1G07NH**
TL OILMOTOR
1A0P9D**
VOLTAGE MOTOR CODE CONDENSER CODE
100V ANDS56** AATP22**
110-120V ANET56** AATP26**
220-240V ANER60** AATP27**
Brown
Brown
Blue
Blue
TL NOISE FILTER B
BREAKER 5A
EARTH WIRE
1A0H0W**
1A0RF3**
TL SLDVALVE CHAIR
1A0P9E**
TL SLDVALVE RLL
1A0P9F**
23
Brown Blue
Yellow Green
Yellow Green
Brown Blue
Yellow Green
Brown Blue
PLUG TYPE CODE
A TYPE 1A0RJJ**
C TYPE 1A0RF4**
BF TYPE 1A0RJH**
AUSTRALIA 1A0RL2**
N L
Noise Filter
Orange
POWER HR SV
Brown Red Orange
Yellow
Green Blue Purple Grey
TL STICK SW H
1A0PBB**
3
Brown Red Yeloow Green Orange
TL SLDVALVE HEAD
1A0P9G**
Brown Red Orange Yellow Green
TL STICK SW(047)
1A0RKS**
STICK SWITCH PCB
1G01Q1**
VOLTAGE 4SOLENOID VALVE CODE
100V 50/60Hz,110V 60Hz 1G07DC**
110 50Hz,115V 50/60Hz,120V 60Hz 1G07DD**
220V 50/60Hz,230V 60Hz 1G07DE**
230V 50Hz,240V 50/60Hz 1G07DF**
Power headrest
HEAD POTENTIO METER L 1A0PBE**
12
Brown Red Orange
TL STICK SW(A-M)
1A0S3T**
2
Brown Red Orange Yeloow Green Blue Purple Grey Black
Brown Red Orange Yellow Green
Brown Red Orange Yellow Green
TL STICK SW(047) 1A0RKS**
TL STICK SW(047) 1A0RKS**
STICK SWITCH PCB
1G01Q1**
STICK SWITCH PCB
1G01Q1**
ManualAuto
VOLTAGE 8SOLENOID VALVE CODE
100V 50/60Hz,110V 60Hz 1G07DG**
110V 50Hz,115V 50/60Hz,120V 60Hz 1G07DH**
220V 50/60Hz,230V 60Hz 1G07DJ**
230V 50Hz,240V 50/60Hz 1G07DK**

TAKARA BELMONT CORPORATION
2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083, Japan
TEL : [phone]
FAX : [phone]