Belnick ES-UN3-24-OAK-GG User manual

Thank you for your purchase!
Customer Service Email: [e-mail] | Phone: [phone]
ES-UN3-24-OAK-GG / ES-UN3-29-OAK-GG / ES-UN3-24-ESP-GG / ES-UN3-29-ESP-GG
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Commercial Grade
Classic Ladderback
Swivel Bar Height
Wood Stool

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address
or phone number shown below to assist you with any product questions or
issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you
may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters are
warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means use
for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if
the product is sold or otherwise transferred. Repairs made by parties other than Belnick also void
this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by
persons exceeding specified weight limits or commercial use exceeding forty hours per week; or (5)
rust or other damage caused by exposure to moisture. The user assumes all risk of injury resulting
from use of this product. Liability for incidental or consequential damage is excluded. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

ASSEMBLY INSTRUCTION
IMPORTANT NOTE:
   

  
PAS LIST
@  
  Q
1   
      



   
   
  0


4
5
6
7
  
d   





•i�.··
·. . .
©.
0

l
I .·· 
 
18PCS
·  PCS

�c·, !
..
NOTE : Do not tighten all the screws until the stool is fully assembled.


 


0

Attach the Chair Legs (Part B) to the Apron
with Swivel Plate (Part D), then attach the
Footrest (Part C) to inside of the Chair Legs
(Part B) using (12) M6x40mm Hex Screws
(Part 2), (12) Lock Washers (Part 3) and (12)
M6x13mm Flat Washers (Part 4). Loosely
tighten using Allen Wrench (Part 6).

STEP 2


�

STEP 3
ASSEMBLY INSTRUCTION
4x
 

0
0

Invert Cushioned Seat (Part E) and place on a stable
raised surface such as a table. Attach the Backrest
(Part A) to the Cushioned Seat (Part E) using (4)
M6x40 mm Hex Screws (Part 2), (4) Lock Washers
(Part 3) and (4) 6.5x 1 6.5 mm Flat Washers (Part 5).
T ighten using Allen Wrench (Part 6).
Keep the Backrest (Part A) and Cushioned
Seat (Part E) inverted on a stable raised
surface. Attach the Swivel Plate located on
the Apron with Swivel Plate (Part D) to the
Cushioned Seat (Part E) using (4) M6x25 mm
Hex Screws (Part 1 ) and (4) 6.5x16.5 mm Flat
Washers (Part 5). Return Chair to the upright
position and securel y tighten all screws using
Allen Wrench (Part 6).
ENSURE THAT ALL SCREWS ARE FULLY TIGHTENED BEFORE USE.
Finish attaching the Backrest (Part A) to the
Cushioned Seat (Part E) using (2) M6x40MM Hex
Screws (Part 2), (2) Lock Washers (Part 4) and (2)
Flat Washers (Part 5). Loosely tighten using Allen
Wrench (Part 7).