Belnick ET-ER18345-18-LB-GG User manual

¦¡¦¡¦¡£ဘ 
Customer Service (mail: [email protected] | Phone: [phone]
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
18 Inch LeatherSoft
Dining Chair
Set of 2
ET-ER18345-18-LB-GG, ET-ER18345-18-DB-GG, ET-ER18345-18-GY-GG, ET-ER18345-18-LG-GG
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/ET-ER18345-18-LB-BK-GG.pdf

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-
lasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any
issues you may have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal
usage, according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters
are warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for
the product. In the absence of product-specific restrictions and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by
parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of
leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage
attributable to use by persons exceeding specified weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resulting from use of this product. Liability for
incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

STEP 1
STEP 2
PARTS
A
B
B
C
C
D
D
1PC
1PC
1PC
1PCS
1
2
3
4 1PC
2PCS
2PCS
4PCS
A
1
5
1
4
FRONT
51PC
2
2
3
5
STEP 1: Attach the Right Frame (Part C)
to the Left Frame (Part B) using (2) Short
Bolts (Part 1).Tighten with Large Allen
Wrench (Part 5). Attach Rear Stability Bar
(Part D) to the Left and Right Frames using
(2) Long Bolts (Part 2). Tighten with Small
Allen Wrench (Part 4) and tighten pre-
assembled floor glides on the bottom of the
Left and Right Frames.
Seat
Left Frame
Right Frame
Rear Stabilizing Bar
Short Bolt
Long Bolt
Medium Bolt
Small Allen
Wrench
Large Allen
Wrench
Small Allen Wrench
Long Bolt
Short Bolt
Large Allen Wrench
Left Frame
Right Frame
Rear Stabilizing Bar
Pre-assembled Floor Glides
STEP 2: Turn Seat (Part A) upside down on
a clean, smooth surface and attach frame to
the underside of seat using (4) Medium Bolts
(Part 3) and tighten with the Large Allen
Wrench (Part 4).
Note: Ensure the seat bracket marked
front (see diagram) is facing the front
of the chair.
Left Frame
Right Frame
Medium Bolts
Large Allen Wrench
Seat