Belnick HL-0001-GG User manual

Customer Service Email: [email protected] | Phone: [phone]
HL-0001-GG / HL-0001-DK-GY-GG / HL-0001-GY-GG / HL-0001-BL-GG / HL-0001-GN-GG
HL-0001-OR-GG / HL-0001-PUR-GG / HL-0001-WH-GG / HL-0001-RED-GG / HL-0001-YEL-GG
Mid-Back Mesh
Multifunction Executive
Swivel Ergonomic Office
Chair with Adjustable Arms
Thank you for your purchase!
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all
of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent
scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or
components may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety
Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and
installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/HL-0001-GN-GG.pdf

Have a Question/ Concern?
Quality products and first-class customer service are the cornerstone of long-lasting consumer relationships.
We strive toward excellence in all we do and want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address or phone number
shown below to assist you with any product questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you may have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is warranted from
the original purchase date and to the original purchaser for normal usage, according to the below-referenced
specifications and limitations.
Normal usage means use in compliance with the restrictions and weight limits specified for the product. In the
absence of product-specific restrictions and weight limits, normal usage means use for no more than forty
hours per week by persons weighing 250 lbs. or less. Coverage terminates if the product is sold or otherwise
transferred. Repairs made by parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence, alteration,
assembly, installation, attachments, accident, vandalism, acts of nature or any other event beyond the control
of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or fabric; (3) cosmetic damage that may
result from normal usage; (4) damage attributable to use by persons exceeding specified weight limits or
commercial use exceeding forty hours per week; or (5) rust or other damage caused by exposure to moisture.
The user assumes all risk of injury resulting from use of this product. Liability for incidental or consequential
damage is excluded. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Non-moving metal parts are warranted for 5 years.
Component parts including pneumatic cylinder, control mechanism, base and casters are
warranted for 2 years.
All other items are warranted for 1 year.
•
•
•

PARTS
(1)x1 (2)x1 (3)x1 (4)x2 (5)x1 (6)x5
(7)x1 (8)x1 (9)x10 (10)x10 (11)x1 (12)x1
Chair Back Base Caster
Cylinder CoverGas Lift Cylinder
Lift MechanismSeat Arm 4A Arm 4B
M6 x 25 Bolt M6 x 16 Bolt Allen Wrench Dust Cover
STEP 1 STEP 2
STEP 3
STEP 4 STEP 5 STEP 6
STEP 3A: Place Cylinder Cover (Part 8) over
Gas Lift Cylinder (Part 7) then insert Gas Lift
Cylinder (Part 7) into the Base (Part 5).
STEP 1:Attach Arm 4A and 4B (Part 4) to the underside of the Seat (Part 2) using 3 M6 x
25 Bolt (Part 9) and 3 M6 x 16 Bolt (Part 10).
*Note: TIGHTEN THE BOLTS COMPLETELY.
STEP 2: Attach Lift Mechanism (Part 3) to the underside of the Seat (Part 2)
using 4 M6 x 25 Bolt (Part 9) and 4 M6 x 16 Bolt (Part 10).
*Note: TIGHTEN THE BOLTS COMPLETELY.
STEP 5A: Assemble the Chair back (Part 1) and
seat (Part 2) as shown below.
Height
Controller
Tilt
Backrest
Controller
M6 x 25 Bolt
M6 x 16 Bolt
(10)x4
(9)x4
M6 x 25 Bolt
M6 x 16 Bolt
(10)x3
(9)x3
M6 x 25 Bolt
M6 x 16 Bolt
(10)x3
(9)x3
(4)
(2)
Seat
Arm 4A
(4)
Arm 4B
(8) (7)
Cylinder Cover Gas Lift Cylinder
Base
Step 3B:
Attach Gas Lift Cylinder (Part 7)
and 5 casters (Part 6) into the Base (Part 5)
(5)
Caster
(6)
STEP 4: Place Seat (Part 2) onto the
Gas Lift Cylinder (Part 7).
(2)
(7)
Gas Lift
Cylinder
Seat
Lift Mechanism
(3)
(2)
Seat
STEP 5B: Insert the Chair back (Part 1) into the
Lift mechanism (Part 3) and adjust to desired
height, turn the knob clockwise until it is
screwed in tightly.
(1)
Chair Back
(3)
Lift Mechanism
Dust Cover
(12)
Knob