Belnick GO-2286B-BK-GG User manual

Drafting Chair with
Adjustable Foot Ring
GO-2286B-BK-GG / GO-2286B-WH-GG
Customer Service Email: [email protected] | Phone: [phone]
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/GO-2286B-BK-GG.pdf

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-
lasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any
issues you may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters
are warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means
use for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage
terminates if the product is sold or otherwise transferred. Repairs made by parties other than
Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use
by persons exceeding specified weight limits or commercial use exceeding forty hours per
week; or (5) rust or other damage caused by exposure to moisture. The user assumes all risk of
injury resulting from use of this product. Liability for incidental or consequential damage is
excluded. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.

PARTS
STEP 1 STEP 2 STEP 3
STEP 4
STEP 6
⑴x5 ⑵x1 ⑶x1 ⑷x1
⑸x1 ⑹x1
⑾x
⑺x2
⑻x
⑼
x4
⑽x4
STEP 7
⒀x1
⑿x4
⑷
⑺
⑹
⑽
⑽
Open the hook and loop flap on both sides
of seat first, then place the Back
Cushion⑺on the Seat Cushion (6),and
use 2 bolts ⑽ to attach to the lower screw
holes on Seat Cushion (6) (see diagram).
*Note: DO NOT FULLY TIGHTEN BOLTS.
⑹
⑺
⑽
⑽
(3)
(2)
(1)
⑸
FRONT
⑹
⑼
Push the Back Cushion ⑺up to a vertical
position and attach the Seat Cushion(6)
by using 2 bolts ⑽ then close the hook
and loop flap.
*Note: Tighten the bolts completely.
STEP 5
⑻⑾
⑻
⑿
⑿
⑾
⑸
(3)
Casters
5-Star Base Column Foot Ring
Lift Mechanism Seat Cushion
Back Cushion
Left
Arm
Right
Arm
Short Screw
Medium Screw
Long Screw
Arm Caps Allen Wrench
Casters
5-Star Base
Column
Foot Ring
Seat
Lift Mechanism
Short Screw
Medium Screw
Back Cushion
Seat Cushion
Long Screws
Right Arm
Left Arm
Long Screws
Arm Caps
Arm Caps