Belnick BT-659-BLK-ARMS-GG User manual

Fabric Drafting
Chair with Arms
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: [email protected] | Phone: [phone]
BT-659-BLK-ARMS-GG / BT-659-GRY-ARMS-GG / BT-659-NVY-ARMS-GG / BT-659-BY-ARMS-GG / BT-659-BLACK-ARMS-GG
Thank you for your purchase!

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address or
phone number shown below to assist you with any product questions or issues before
requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you may
have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage, according
to the below-referenced specifications and limitations.
• Non-moving metal parts are warranted for 5 years.
• Component parts including pneumatic cylinder, control mechanism, base and casters are warranted
for 2 years.
• All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means use for
no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if the
product is sold or otherwise transferred. Repairs made by parties other than Belnick also void this
warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence, alteration,
assembly, installation, attachments, accident, vandalism, acts of nature or any other event beyond the
control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or fabric; (3) cosmetic
damage that may result from normal usage; (4) damage attributable to use by persons exceeding
specified weight limits or commercial use exceeding forty hours per week; or (5) rust or other damage
caused by exposure to moisture. The user assumes all risk of injury resulting from use of this product.
Liability for incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.

STEP 1 STEP 2
(3)*1 (4)*1
(5)*1 Footrest (6)*1
Gas cylinder
Base
Seat plate
PARTS
(2)*1
(1)*1 Seat Back Seat
(7)*5 Caster (8)*4 Short Screws
(9)*2 Long Screws (10)*1 (12)*1
Connector Bar (11)*1 Tension Knob Washer
(13)*1 Lock Washer (14)*1 Bracket (15)*1 (16)*1
Spacer Allen Wrench
(8)
FRONT
(2)
(6)
(5)
(7)
(4)
(3)
Footrest
Gas Cylinder
Base
Casters
Seat
Seat Plate
Short Screws
Step 1B:
Insert Gas
Cylinder into
Base.
Step 1A: Insert Casters into Base
Step 1C: Place Footrest onto Gas Cylinder. Step 2: Lay Seat on clean surface and
attach Seat Plate using (4) Short
Screws. Tighten using Allen Wrench.

ARM ASSEMBLY PARTS
(2)*6
STEP 1 STEP 2
Arms(1)*1
FRONT
(2)
(L)*1(R) Screws
STEP 3
STEP 3
(1)(1)
(1)(1)

STEP 5
STEP 6
STEP 3
STEP 3
(9)
(1)
(10)
(15)
(14)
(11)
(13)
(2)
(12)
(3) (10)
(10)
(3)
(4)
STEP 3
STEP 3
STEP 3
STEP 4
Seat Back
Spacer
Bracket
Long Screws
Connector Bar
Seat
Connector Bar
Tension Knob
Washer
Lock Washer
Seat Plate
Seat Plate
Gas Cylinder
Step 3: Attach the Connector Bar to the
Seat Back using (1) Spacer, (1) Bracket,
and (2) Long Screws. Tighten using Allen
Wrench.
Step 3: Insert the Connector Bar into the
Seat Plate. Place the Tension Knob through
the Lock Washer and Washer into the Seat
Plate and turn clockwise to tighten.
Step 5: Place the Seat Plate onto the Gas
Cylinder and push down.
Step 6: Ensure all screws are tightened.