Belvedere 8600 User manual

PAGE 1 of 4
Shampoo
Bowls 8600 PIVOTING SHAMPOO BOWL
8600
Belvedere USA LLC
One Belvedere Boulevard, Belvidere, Illinois 61008
Printed in U.S.A. 4001024 Rev. 09-07
NOTE: To familiarize yourself with the various
components, please read instructions through
before starting.
1. Attach the fixture to the bowl according to
the instructions packed with the fixture.
TO ATTACH HOSE RECEIVER TO
BOWL (STEPS 2 thru 6).
2. To make hose receiver installation easier,
complete these steps to cut screw threads
in the mounting holes:
STake a mounting screw and drive it
2 or 3 turns into one hole.
DO NOT OVERTIGHTEN.
SRemove the screw.
SRepeat for all four (4) mounting holes.
If the bowl is not equipped with a vacuum breaker,
proceedtoStep4.
*NOTE: If you ordered a vacuum breaker,
your hose receiver will have two
holes for mounting the vacuum
breaker.
VACUUM
BREAKER
HOSE
RECEIVER
GASKET
NUTS
3. Place the vacuum
breaker pipes
through the
Gaskets and the
holes in the
hose receiver as
shown.
Secure the vacuum
breaker to the hose
receiver with
two hex-nuts.
DO NOT
OVERTIGHTEN.
NOTE: Install the vacuum
breaker as shown.
If the vacuum breaker is
installed backwards,
it will interfere with the
Spray.
8600 BACKWASH SHAMPOO BOWL
WITH VACUUM BREAKER
AND MODEL 522 FIXTURE
INSTALLATION AND PLUMBING
4. Place the gasket
over the flange
on the bottom
of the hose
receiver.
VACUUM
BREAKER
HOSE
RECEIVER
GASKET
VACUUM BREAKER
MOUNTING HOLES
MOUNTING
SCREW
DRIVE
SCREW
IN 2 OR 3
TURNS

9. From the underside of the bowl, place
the Rubber Washer over the Strainer
Body. Secure the strainer
body with the Nut.
DO NOT OVERTIGHTEN.
When the
Strainer
Body is
tightened
securely to
the bowl,
clean off
any excess
plumber’s
putty.
10. Attach the
Gasket and
Tailpiece to
the Strainer
Body.
DO NOT
OVERTIGHTEN.
7. Apply a liberal
amount of
plumber’s putty
(available
at most
hardware
stores)
around the
top of the
drain opening.
5. Place the hose receiver in the bowl with the
large hole in the dome facing the front of
the bowl. Install the mounting bracket on
the bottom side of the bowl with four (4)
embossed corners
facing upward,
against the
bottom of
the bowl.
Secure with
four (4)
mounting
screws.
DO NOT
OVERTIGHTEN.
6. If your bowl is not equipped with a
vacuum breaker, attach the Spray Hose
connector to the fixture tailpiece.
If your bowl is equipped with a vacuum
breaker, connect one end of the fixture
hose to the inlet side of the vacuum
breaker. Connect the other end to the
fixture tailpiece. Attach the Spray Hose
connector to the vacuum breaker outlet.
PLUMBER’S
PUTTY
DRAIN
OPENING
STRAINER
BODY
PLUMBER’S
PUTTY
DRAIN
OPENING
INSTALLING THE DRAIN ASSEMBLY
(STEPS 7-10)
8. Place the
strainer body
in the opening,
and press it
into the
plumber’s putty.
TAILPIECE
GASKET
BOWL
RUBBER
WASHER
STRAINER
BODY
BOWL
NUT
PAGE 2 of 4
DOME
MOUNTING
SCREW
EMBOSSED
CORNER
(UP)
SPRAY
HOSE
RECEIVER TAILPIECE
HOSE RECEIVER
WITH VACUUM
BREAKER
INLET
OUTLET FIXTURE
HOSE
SPRAY
TAILPIECE

11. Install the wall bracket so that the mounting
holes are at 31” from the finished floor. (This
bracket height is suggested to obtain the
neckrest height
suitable
for most
stylists.
The bracket
height may
be varied
to suit
personal
preference.)
Be sure
that the
bracket is
securely fastened
to a structural
member in the wall,
and is level.
ALL PLUMBING TO BE PLANNED AND
PERFORMEDBYAQUALIFIEDPLUMBER
IMPORTANT NOTE:
It is the responsibility of the owner
and/or the installer to be sure that
the installation conforms to all local
plumbing codes and regulations.
PAGE 3 of 4
TO MOUNT THE 8600 BOWL TO
THE WALL (STEPS 11 THRU 13)
12. Set the bowl onto the bracket and attach
using four (4) 1/4-20 bolts supplied.
Make sure the bolts are tight.
13. Connect the fixture to the hot and cold
supply lines. The supply lines must be
flexible braided hose. Install the flexible
drain hose to the trap.
TRAP SUPPLY LINES
BOWL
CLEANING INSTRUCTIONS
Paste wax monthly to preserve and protect
against common soils. With normal care, your
bowl will last many years.
CLEANONLYWITHANON-ABRASIVE
LIQUID CLEANER.
Dow Tub & Tile CleanerR409R
Mr. CleanRFantasticR
DO NOT USE HARSH ABRASIVES
These will dull the sparkling surface.
See back page for rough-in specifications.
BRACKET
FLOOR LINE
31”TOMOUNTINGHOLES

PAGE 4 of 4
ROUGH-IN PLUMBING SPECIFICATIONS.
IMPORTANT! DO NOT
OVERTIGHTEN
DRAIN ASSEMBLY!
31/2”BASKETSTRAINER
SIDE
VIEW
FRONT
VIEW
TOP VIEW
BOWL
COLD
HOT
FINISHED FLOOR LINE
APPROX.
16” 12”
34 3/4”
RECOMMENDED
31” FROM
MOUNTING
HOLES TO
FLOOR
4” 4”
CLEANING INSTRUCTIONS
Paste wax monthly to preserve and protect against common soils.
With normal care your bowl will last many years.
CLEAN ONLY WITH A NON-ABRASIVE LIQUID CLEANER.
Dow Tub & Tile CleanerR409R
Mr. CleanRFantasticR
DO NOT USE HARSH ABRASIVES.
These will dull the sparkling surface.
IMPORTANT NOTE:
This shampoo bowl is designed to be used with the Belvedere SR04 and SR24 Siesta Backwash Shampoo
Chairs. It can also be used with Belvedere Reclin-O-Matic shampoo chairs.
For optimum comfort when the bowl is used with Siesta Backwash Chairs, install the bowl
so the neckrest is at 34-3/4” above the finished floor.
To mount the bowl at these heights, locate the bowl bracket height as shown in these specifications.