bemodern Pryzm 750 Guide

1
Impero Marble Wall Suites
Pryzm 750, 1000
Instructions for installation
Patent pending
UK Registered Design
R2 Aug 2019 200784_2

2
Contents
Technical Specs 3
Contents of Fixings Box 4
Installation –Wall Marble 5 - 9
Maintenance 10
200784_2

3
Technical Specification of suites
Fire Description Logs
Dimensions
A B C D E
57” IMPERO
PRYZM 5D 1000 Micro Marble
Wall Hung
4 LRG 1320mm 619mm 290mm 1450mm 195mm
47” IMPERO
PRYZM 5D 750 4 SML 1070mm 619mm 290mm 1200mm 195mm
200784_2

4
Contents of fixings box
L -Wall Bracket
Wall Bracket
Adjustable Top
Support
(x2)
(x2)
Nuts, Bolts and Washers
8 x 16mm round dome head
fixing screws (A)
(x18)
*Please note the L-Wall brackets come pre-assembled with the top support brackets.
Predrilled Plywood
Fixing Panel (x1)
located in the rear
of the surround
6 x 13mm flange head
fixing screws (B)
(x12)
Mantle Hooks (x2)
(x4)
IMPORTANT NOTE:
Wall fixings (i.e. screws/wall plugs etc.) are not supplied as these are crucially
dependent upon the type of wall and surface the surround is going to be fixed
too.
The installer is therefore responsible for ensuring that suitable fittings are used
according to the particular model to be installed as well as individual fitting
situations and environments. All mechanical fixings, for holding the suite in position,
must be secured to a solid wall or structure.
(x4) (x4)
(x4)
200784_2

5
Installation –Wall Marble
Before the surround can be installed, consideration will need to be given to routing the power
supply to the fire. This will affect the stages of the installation process. We advise a qualified
electrician conduct any electrical parts of the installation.
Unpack your new suite and locate the Plywood fixing panel. Please note this installation guide is
detailed for both 750 and 1000 Pryzm so please familiarise yourself with the model you have
purchased before beginning installation. The plywood fixing panel is to be used so the weight of
the surround can be distributed across a larger area and enable the installer to achieve a good
solid fix to the wall in various points across the panel as detailed in the following instruction.
Note: the surround / fixing panel is a two adult
person lift. A second person will be required to lift
and support the surround fixing panel.
Once the location and desired height has been decided, mark the centre of the space where the
fixing panel / surround will be installed at the desired height (See Xon Diagram 1). Draw a horizontal
line using a spirt level . Holding the fixing panel up so the bottom of the panel corresponds with the
line. (It is recommended a minimum of twelve fixings are used). Drill through the plywood panel
marking the wall in the twelve fixing locations, remove the plywood fixing panel away from the wall,
drill and plug the wall with the correct fixings for the wall medium –See important note below .
Beads of silicone / no nails should be applied to the back of the fixing panel prior to firmly securing
to the wall.
200784_2
The first step to installation will
be the fitment of the fixing
panel (See Diagram 1) in the
desired position in the room.
Decide on the location of the
surround and the desired
installation height, we
recommend a height (C)
between 300mm and 500mm
from the floor, however the
product can be installed at any
desired height. If fixing into a
stud wall locate the studs and
consider positioning the fixing
panel / surround over as many
studs as possible. (Min of 2 studs
recommended. Additional
fixings should be used if less
than two studs can be located)
Note: The bottom of the fixing
panel corresponds with the
bottom of the surround.
IMPORTANT NOTE:
Wall fixings (i.e. screws/wall plugs etc.) are not supplied as these are crucially
dependent upon the type of wall and surface the surround is going to be fixed too.
The installer is therefore responsible for ensuring that suitable fittings are used according
to the particular model to be installed as well as individual fitting situations and
environments. All mechanical fixings, for holding the suite in position, must be secured
to a solid wall or structure.
Diagram 1

200784_2 6
Diagram 2
Once the assembled fixing panel is secured in place, attach the two off L- wall brackets onto the
plywood panel in the pre-drilled locations using 9 x screw (A) to secure each bracket. See
diagram 2 below.
Installation –Wall Marble Note: the surround / fixing panel is a two adult
person lift. A second person will be required to lift
and support the surround.
1. Position Hearth
Diagram 3
Carefully lift the hearth down onto the L
brackets. Please ensure the rear of the
hearth is flush with the wall. To secure the
hearth in place, screw through the holes
detailed in Diagram 3 into the timber
mounting panels on the underside of the
hearth.
(2 x fixing screws (B) per L- bracket).
It may be necessary to use a packing
piece between the bracket and hearth
mounting panels if the hearth does not sit
flush on the bracket

7
Installation –Wall Marble continued
Diagram 5
Diagram 6
The top of the leg sections have angle
brackets fitted for securing direct to the fixing
panel (see diagram 5).
These fixing brackets will prevent the surround
from detaching itself from the wall.
Diagram-6 illustrates how the angle brackets
(fitted to the internal leg of the surround) are
secured behind the hook brackets at the
final fitting stage. This is achieved by carefully
positioning the surround on the hearth in its
intended position and marking the position of
the hook bracket screw holes through the
central opening in the surround.
6. Top Bracket
5. Angle Brackets
200784_2
Once the hearth is secured
carefully lift the main body onto
the hearth over the L-bracket
and centralise on the hearth cut-
out. (52mm each side)
See Diagram 4.
2. Fit Main Body
Diagram 4

8
9.
10. Adjustable Top Support
Diagram 9
Diagram 10
To secure in place, screw the adjustable wall
brackets top supports through the holes detailed
in Diagram 9 into the timber mounting panels.
Fixing screw (B) 2 per bracket.
Finally tighten the nuts and bolts to
lock the adjustable bracket in
place. - See Diagram 10.
200784_2
Once the brackets are secured
carefully lift the main body onto
the hearth over the L-bracket
and hooks, centralise on the
hearth cut-out. (52mm each
side) See Diagram 8.
8. Fit Main Body
Diagram 8
Remove the surround and securely fix the hook
brackets to the fixing panel using 4 x fixing
screw (B) - 2 per bracket. Diagram 7
Diagram 7
7. Fix Hook Brackets
Installation –Wall Marble continued

9
Installation –Wall Marble continued
12. Secure fire
To secure the fire in place, make sure it is
centralised in the opening and then screw the
fire to the timber mounting panels through the
fire mounting points (6 x 15mm fixing screws are
supplied with the fire). Once the fire is secured in
position the fire trim can then be placed in
position. The trim has a magnetic fixing.
Diagram 12
13. Installation Complete
Please refer to “Dressing the Logs” section of the
fire instructions which will guide you through the
recommended log layout for your fire.
Diagram 13
Before installing the fire, please unpack it carefully
and place the box containing the logs to one side.
Place a protective covering over the hearth to
prevent the fire scratching the polished surface.
The Pryzm fire can now be installed in the surround
by lifting the fire at a slight angle to allow the fire to
be positioned in the upper section of the surround
opening. Then swing the rear of the fire in to the
surround, lowering the fire down onto the L Wall
Brackets.
Great care must be taken not to crush or damage
the cable or damage the hearth on installation .
Note: The fire power cable may need positioning in
place prior to the installation of the surround upper
body, if a socket is to be used.
11. Install the Fire
Diagram 11
200784_2

10
Maintenance
WARNING: Before any maintenance or whilst cleaning the exterior of the fireplace, the
unit should be disconnected from the power supply until it has cooled down.
Cleaning the Fire
Cleaning or polishing products are not recommended. Fingerprints or other marks on
the front glass panel can be removed by a piece of soft, damp, lint-free cloth with a
good quality household glass cleaner. The front glass panel should always be
completely dried with a clean, lint-free cloth or paper towel.
Wipe up spills and condensation immediately with a clean damp cloth. When
cleaning the furniture, we also recommend using a clean damp cloth. Avoid using
cleaners or polishes that contain abrasives, solvents, acid and ammonia.
CAUTION: Abrasive cleaners should not be used on the glass panel. Liquids should not
be sprayed directly onto any surface of the unit.
Troubleshooting
Should you have any queries regarding this product please contact Customer Services
on 01914300901 or email us at [e-mail]
Recycling
All cardboard packing is recyclable.
200784_2
IMPORTANT NOTE:
Wall fixings (i.e. screws/wall plugs etc.) are not supplied as these are crucially
dependent upon the type of wall and surface the surround is going to be fixed too.
The installer is therefore responsible for ensuring that suitable fittings are used according
to the particular model to be installed as well as individual fitting situations and
environments. All mechanical fixings, for holding the suite in position, must be secured
to a solid wall or structure.