BenQ PX9230 User manual

English
1
Table of Contents
Notice..................................................................................................... 2
Cooling notice ................................................................................................................ 2
When edge blending...................................................................................................... 2
Product information ............................................................................. 3
Packing content.............................................................................................................. 3
Specication ................................................................................................................... 3
Terminals ........................................................................................................................ 4
Remote control .............................................................................................................. 5
Installation ............................................................................................. 6
Lens ................................................................................................................................. 6
Projection table.............................................................................................................. 6
Lens shift range .............................................................................................................. 8
Projector dimension ............................................................................. 10
Lens dimension...................................................................................... 11
RS232 command ................................................................................... 12
RS232 pin assignment.................................................................................................... 12

English
2
Notice
Cooling notice
yVentilation
Air inlet
Air outlet
yCaution for installation
For proper ventilation of the projector, make sure to leave some space around the projector as
shown in the illustration below:
• Table
50cm
above
50cm
above 70cm above
• Ceiling • Stacking
30cm above
Minimum 100mm
When edge blending
• To avoid the image shaking or some pixels in the display may be misaligned, do not use the
projector in the following location:
• In a building close to a construction site.
• In a room where an air conditioner unit is working and it vibrates.
• In a place where the temperature changes dramatically that may cause thermal contraction.
• Before making any adjustment, leave the projector lit for at least 15 minutes after its light source
is turned on. This allows the internal temperature of the projector to stabilize.

English
3
Product information
Packing content
Installation Guide
Power cable
Remote control Projector with anti-dust cap Batteries
VGA cable
Digital Projector
Installation Guide
Regulatory Statement Warranty card
Specication
PX9230
Projection system DLP Single 0.7 XGA DMD Chip
Native resolution 1024*768 pixels, 4:3
Brightness 6000 Lumens
Light source UHP Lamp
Power consumption 480Watts (Normal mode)/ 355Watts (Eco mode)
Dimension 431.0 x 167.0 x 320.5 mm
Weight 8.5 kg (without lens)
Note:
• The brightness is supplied by standard lens, the value will depends on lenses.
• The brightness output will vary depending on each units and actual usage.
• Pleasendthelatestuser’smanualonthelocalwebsite.

English
4
Terminals
HDMI
Connection to HDMI source.
DVI-D
Connection to DVI source.
DISPLAY PORT
Connection to DISPLAY PORT source.
LAN
For connection to RJ45 Cat5/Cat6 Ethernet cable to control the
projector through a network.
3D SYNC IN
Connect 3D sync in cable from a computer or an enabled device.
3D SYNC OUT
Connection to 3D IR sync signal transmitter.
USB 1.5A
Support 5V/1.5A output.
COMPUTER-1, COMPUTER-2
15-pin VGA port for connection to RGB, component HD source, or PC.
AUDIO IN-1/-2
Connection to an audio input source via an audio cable.
MONITOR OUT
Connection to other display equipment for concurrent playback display.
AUDIO OUT
Connection to a speaker or headset.
COMPUTER-3 (R/Pr, G/Y, B/Pb, H,V)
Connection to RGB signal with BNC type input terminal.
USBTYPE-B
Maintenance exclusive port for authorized maintenance personnel only.
COMPONENT (Y, Pb, Pr)
Connect to Component source.
AUDIO IN-3/-4(L/R)
Connection to an audio input source via an audio or audio L/R cable.
RS-232
Standard 9-pin D-sub interface for connection to PC control system and
projector maintenance.
S-VIDEO
Connection to S-VIDEO source.
VIDEO
Connection to a video source.
WIRED REMOTE
Connection to remote control for wire remote control.
12VTRIGGER
3.5mm mini earphone jack, employs 200mA display relay to provide
12(+/-1.5)V output and short circuit protection.
Caution:
Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged in
case of an invalid port, e.g. a wired remote controller is connected to trigger output.

English
5
Remote control
On
KEYSTONE +/-
Up
Left
MENU
PICTURE
INPUT
AUTO SYNC
FREEZE
OVERSCAN
Numeric buttons
3D MODE
CLEAR
VOLUME +/-
Off
QUICK INSTALL
MUTE
ENTER
Right
EXIT
Down
NETWORK
ASPECT
BLANK
LAMP MODE
INFO
LIGHT
ID SET
SHUTTER
WIRE REMOTE jack
yRemote ID setting
Press ID SET to set remote ID.
Press ID SET for three seconds.The POWER indicator on the remote control blinks, then press
01~99 to designate an ID.
Press CLEAR and ID SETforveseconds.ThePOWERindicatorontheremotecontrolblinksa
single instance to signify a switch from control by projector only or control by projector to remote
control.

English
6
Installation
Lens
Model Lens Type Part Number Throw Ratio Lens Shift
LS2ST3 Widex 5J.JDH37.002 0.81 Vertical: -10%-50%
Horizontal: -5%-5%
LS2ST1 Wide zoom 5J.JDH37.011 1.14-1.347 Vertical: -10%-50%
Horizontal: -5%-5%
LS2SD2 Standard 5J.JEN37.001 1.6-2 Vertical: -10%-50%
Horizontal: -5%-5%
LS2LT1 Semi long 5J.JDH37.032 2-3 Vertical: -10%-50%
Horizontal: -5%-5%
LS2LT2 Long zoom 5J.JDH37.041 3.11-5.18 Vertical: -10%-50%
Horizontal: -5%-5%
Projection table
Image Height
Image Width
Diagonal
Projection Distance
Projection Image
Image Hight
h
h
O
A
A
h
h
Screen size Wide Fix Lens Wide Zoom Lens Standard Lens
Diagonal Width Height Distance
NA Wide Tele Wide Tele
Inch mInch mInch mInch mInch mInch mInch mInch m
80 2.03 64 1.63 48 1.22 52 1.32 73 1.85 86 2.19 102 2.60 128 3.25
100 2.54 80 2.03 60 1.52 65 1.65 91 2.32 108 2.74 128 3.25 160 4.06
120 3.05 96 2.44 72 1.83 78 1.98 109 2.78 129 3.28 154 3.90 192 4.88
150 3.81 120 3.05 90 2.29 97 2.47 137 3.47 162 4 .11 192 4.88 240 6.10
200 5.08 160 4.06 120 3.05 130 3.29 182 4.63 216 5.47 256 6.50 320 8.13
300 7.62 240 6.10 180 4.57 194 4.94 274 6.95 323 8.21 384 9.75 480 12.19
400 10.16 320 8.13 240 6.10 259 6.58 365 9.27 4.31 10.95 512 13.00 640 16.26
Screen size Semi Long Lens Long Zoom
Diagonal Width Height Distance
Wide Tele Wide Tele
Inch mInch mInch mInch mInch mInch mInch m
80 2.03 64 1.63 48 1.22 128 3.25 192 4.88 199 5.06 332 8.42
100 2.54 80 2.03 60 1.52 160 4.06 240 6.10 249 6.32 414 10.53
120 3.05 96 2.44 72 1.83 192 4.88 288 7.32 299 7.58 497 12.63
150 3.81 120 3.05 90 2.29 240 6.10 360 9.14 373 9.48 622 15.79
200 5.08 160 4.06 120 3.05 320 8.13 480 12.19 498 12.64 829 21.05
300 7.62 240 6.10 180 4.57 480 12.19 720 18.29 746 18.96 1243 31.58
400 10.16 320 8.13 240 6.10 640 16.26 960 24.38 995 25.28 1658 42.10

English
7
Note:
• Ceilinginstallationmustbedonebyaqualiedprofessional.Contactyourdealerformoreinformation.Itisnot
recommended you install the projector yourself.
• Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.
• Do not use the projector in an environment where extreme temperature occurs. The projector must be used
at temperatures between 41 degrees Fahrenheit (5 degrees Celsius) and 104 degrees Fahrenheit (40 degrees
Celsius).
• Screen damage will occur if the projector is exposed to moisture, dust or smoke.
• Do not cover the vents on the projector. Proper ventilation is required to dissipate heat. Damage to the
projector will occur if the vents are covered.

English
8
Lens shift range
yLens shift adjustable range
The adjustable range for lens shift is tabulated below and subject to the conditions listed.
Desk-Front Projection Normal projection position
Width of projected image
Height of projected image
Height of projected image
Vertical shift
Vertical shift
Vertical shift
Vertical shift
Shift to Left Shift to Right
Max 0.5V
Max 0.5V
1V
1V
1H 0.05H0.05H
Max 0.1V
Ceiling Mount-Front Projection
yCeiling Mount Installation
H
C
0.05H
Screen Top
Screen Center
Shift Range
C = Distance from lens to screen

English
9
BenQ PN Description
5J.JCY10.001 Ceiling mount (CM00G4)
98.0 (3.85)
547.8 (21.56)
372.8 (14.67)
yDesktop Installation
C
H
0.05H
Shift Range
Screen Center
Note:
• The drawings apply to the standard lens only.
• Lens Shift feature is not available to LS2ST3 (Fix Lens). This lens should be used for "zero degree"/"no-offset"
applications. See below:
C
113.5 Screen Center
FOR USE WITH LS2ST3 (FIX LENS) ONLY

English
10
Projector dimension
AIR INLET
AIR EXHAUST
M4x12L
320.5 (12.61) 334.5 (13.16)
431.0 (16.96)
260.0 (10.23)
174.5 (6.87) 156.0 (6.14)
64.0 (2.51)
83.0 (3.26)
240.0 (9.44)
73.5 (2.89)
26.5 (1.04)
165.0 (6.49)
130.0 (5.11)
316.9 (12.47)