Berker 8522 11 0 Series User manual

1/6
09/2015
Blind insert comfort
Blind insert comfort
Order no.: 8522 11 0x
Operating instructions
1. Safety instructions
Electrical equipment may only be installed and assembled by a qualied electrician in
accordance with the relevant installation standards, guidelines, regulations, directives,
safety and accident prevention regulations of the country.
Failure to comply with these instructions may result in damage to the device, re or other
hazards.
Hazard due to electric shock. Disconnect before working on the device. Take into
account all circuit breakers that supply dangerous voltages to the device.
Hazard due to electric shock. The device is not suited for safe disconnection of the
mains supply.
Hazard due to electric shock. Do not operate device without application module.
If several drives should be connected in parallel to one output, it is mandatory to observe
the manufacturer's data; use a cut-off relay where required. Motors could be destroyed.
Use blind drives with mechanical or electrical nal position switches only. Check nal
position switches for correct adjustment. Observe motor manufacturer's data. The device
can be damaged.
Use blind push-buttons only for extension unit operation. The use of blind push-buttons
can cause malfunctions.
Risk of injury. Use the device to control blind and shutter drives or awnings only. Do not
switch any other loads.
Observe the motor manufacturer's data regarding change-over time and max.
switch-on time (ED).
Do not lay control lines in parallel to the motor lines (danger of coupling).
These instructions are an integral component of the product and must be retained by the
end user.

2/6
09/2015
Blind insert comfort
2. Design and layout of the device
(2)
(1)
(3)
(5)
(4)
(6)
Figure 1: Shutter insert
(1) Shutter insert
(2) Frames
(3) Application module bottom part e.g. from a push-button for blinds
(4) Screw for dismantling protection (not R.1/R.3)
(5) Blind button design cover
(6) Connecting terminals
3. Function
Correct use
–Switching electrically operated blinds, shutters, awnings and similar hangings.
–circuiting of extension units push-buttons for blinds, blind inserts, key push-buttons for
blinds
–Only suitable for use in indoor areas with no drip and no spray water.
–Installation into wall box according to DIN 49073.
–Operate with suitable application module (see Chapter 6.2, "Accessories")
Product characteristics
–2 mechanically and electrically mutually locked relay contacts.
4. Operation
These instructions describe the installation of the shutter insert. The operation and function of
the application modules are described in the instructions of the respective application module.
The operation of extension units is only possible if a cover is attached to the main unit.

3/6
09/2015
Blind insert comfort
5. Information for electricians
5.1 Installation and electrical connection
DANGER!
Touching live parts can result in an electric shock.
An electric shock can be lethal.
Disconnect the connecting cables before working on the device and cover all live
parts in the area!
Circuiting and mounting of shutter insert
Figure 2: Shutter insert circuiting diagram
A MCB max. 10 A has been installed as device protection.
Circuit shutter insert according to circuiting diagram (Figure 2)
Mount shutter insert in wall box (recommended: deep box). The connecting terminals must
be at the bottom.
Attach frame and application module (see instructions for application module).
Control by sensors
Sensors such as wind/precipitation sensors are used e.g. to protect awnings from damage. If a
threshold is exceeded on the sensors, blinds/awnings etc are retracted.
When using sensors, the operating mode might have to be changed to protection mode
(see Cover instructions).
(7)
(7) Sensor (e.g. wind/precipitation)
Connect sensor according to connection diagram (Figure X).

4/6
09/2015
Blind insert comfort
Individual control with push-button for shutter extension unit
Individual control with push-button for blind extension unit according to circuiting diagram
503520
Individual control with key push-button for shutter extension unit
Circuit individual control with key push-button for shutter extension unit according to circui-
ting diagram

5/6
09/2015
Blind insert comfort
Master and group control
Circuit master and group control according to circuiting diagram
Master control under application of various RCCBs
Circuit master control under application of various RCCBs according to circuiting diagram

6/6
09/2015
Blind insert comfort
6. Appendix
6.1 Technical data
Rated voltage AC 230 V, + 10 % /- 15 %
Mains frequency 50/60 Hz
MCB max. 10 A
Switching current 5 A (R/L)
Change-over time to the opposite running direction 0.6 sec.
Standby power consumption < 0.1 W
Relative humidity 0 ... 65 % (no condensation)
Operating temperature -5°C … +45°C
Storage/transport temperature -20°C … +60°C
Extension unit cable length max. 50 m
Load cable length max. 100 m
Number of extension units unlimited
Connecting terminal 1 x 4 mm² or 2 x 2.5 mm²
Mounting orientation connecting terminals downwards
Housing installation depth 22 mm
Claw guide installation depth 32 mm
6.2 Accessories
Push-button for blinds order no. 8524 11 xx
Blind time switch order no. 8574 11 xx
Radio push-button for shutters quicklink order no. 8524 51 xx
Radio shutter timer quicklink order no. 8574 51 xx
6.3 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
Our products are under guarantee within the scope of the statutory provisions.
If you have a warranty claim, please contact the point of sale or ship the device postage free
with a description of the fault to the appropriate regional representative.