Bernini Maria 3-in-1 Bird Feeder, Fountain & Planter User manual

Water
Tube
Dancing
Water
Attachment
Fountain Top
With Battery
Compartment
& Water Pump
Inner
Water Bowl
Fountain Base
Base
CONTENTS:
Fountain Assembly
Water
Pump
Battery
Compartment
(4 1.5v AA
Batteries not
Included)
Water
Pump
Tube
Lower
Fountain
Position
Upper
Fountain
Position
Base
Inner
Water
Bowl
Fountain
Feet
Battery
Compartment
Screws
x2
Maximum
Water
Level
Start/Stop
Button
Dancing Water
Attachment
Locating Dowls
Alignment
Notch
Alignment
Notch
Minimum
Water
Level
Fountain
Base
Fountain
Top
Diagram 1a:
OWNERS MANUAL
INSTALLING BATTERIES:
1. Lift Fountain Top with Battery Compartment & Water
Pump out of the Fountain Base (Figure 5). Disconnect
the Water Tube from the Battery Compartment.
2. Unscrew (counter clockwise) the Battery Compartment
Screws and open cover (Figure 1a, 1b).
3. Orient the Battery Compartment with locating dowel on top.
(See Arrow Figure 2a& 2b).
4. Requires 4 AA Batteries (Not Included). Insert 2-1.5v AA
Batteries with the (+) side facing up in Battery Compartment and
2 AA Batteries with the (-) facing up in Battery Compartment
(Figure 2a).
5. Reinstall the Fountain Top by aligning the locating dowel in
the Battery Compartment and Fountain Top. Set the Battery
Cover down onto the Battery Compartment ensuring the dowel
sets into the alignment hole. Tighten the Battery Cover Screw by
turning clockwise. NOTE: You may need to apply pressure to
the Battery Compartment Screws while tightening for the
threads to catch.
1. Take the Fountain Top/Battery Compartment and Water Pump, connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the
Battery Compartment (A & B of Figure 4).
2. Lower the Fountain Top with Battery Compartment and Water Pump into the Fountain Base. There are two locating dowels and two alignment notches that help
you align the Fountain Top to the Fountain Base. Fit these into place and press to Fountain Top and Base together to secure (Figure 6).
OPERATING YOUR FOUNTAIN:
The Fountain has a 1 or 2 hour timer and will repeat at the same time every day.
Turn Fountain on and daily set timer: When the fountain is off, set the run time for 1 or 2 hours by slowly pressing the button 1 to 2 times. Three seconds
after pressing the button, the LED light will repeatedly flash the number of times the button was pressed. This indicates the number of hours the Fountain will run
every day. The Fountain will turn on at the same time, for the selected number of hours, daily thereafter.
Stop Fountain for one day: Press the button for less than 2 seconds. The LED will flash three times.
Turn off the daily timer: Press the button for less than 2 seconds. Then press and hold button again for over 2 seconds, the LED will flash solid for 2 seconds.
,
DANCING WATER ATTACHMENT (OPTIONAL): When Fountain is not running, attach the Dancing Water Attachment to the outlet in the middle of the Fountain
Tower (Figure 8a, 8b and 8c). To prevent overspray, use a larger bowl.
*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO ASSEMBLE YOUR NEW FOUNTAIN
Figure 6
Figure 7
Figure 5
Figure 1b
Figure 1a
Figure 3b
Figure 2b
Figure 4
A
B
Figure 3a
Figure 2b
STEP
2.
STEP
3.
STEP
Figure 2a
CHANGING BATTERIES:
1. Remove any Dancing Water Attachment, lift Battery
Compartment and Water Pump out of the Fountain (Figure 5),
ensure Battery Compartment and Water Pump are completely
dry before opening Battery Compartment. It is important that
no water enters the Battery Compartment.
2. See Installing Batteries Section above on how to reinstall
batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 6).
Figure 7b
Figure 7a
ButtonButton
Need Help?
Call us for assistance at:
[phone]
or you can email us at:
customercare@
berninifountains.com
For video tutorials visit:
berninifountains.com/support
Our Customer Care Department is available:
Monday - Friday 8:30am to 4:00pm PST
11:30am - 7:00pm EST
Locating
Dowel
Locating
Dowel
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Fountain
Top
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Fountain
Top
Battery Compartment
Retaining Screws X2
Battery Compartment
Retaining Screws X2
Battery Cover
Retaining Nut
Battery Cover
O-Ring
Battery Cover
Retaining Nut
Battery Cover
O-Ring
Battery Cover
O-Ring
Figure 8b Figure 8c
Figure 8a
Dancing Water Attachment
Note: Due to splashing and overspray
it is recommended that the Dancing
Water Attachment be used outdoors.
Please note, images of parts
are not to scale with one another.
Battery Cover
O-Ring
Wire Hook
Hanger x3 &
Bird Feeder
Cover x3
Maria 3-in-1 Bird Feeder, Fountain & PlanterTM
Please Note: Please remove the packing
material inside Fountain Tower that says
“REMOVE BEFORE USE”.

Troubleshooting Troubleshooting Guide
OWNERS MANUAL
4.
STEP
Care and Maintenance
5.
STEP
001158 BM3IO rev 6d us
Step 1 Step 2 Step 3 Step 4
COLD STORAGE
Turn power off, remove from container, clean and dry the Fountain of all water. Remove the batteries for long term storage and bring it indoors. (Now is a great time to clean the pump to remove any
debris that may have accumulated throughout the year).
CLEANING YOUR FOUNTAIN
In order to keep your Fountain in tip-top shape and for a prolonged life, it is best if your Fountain and the bowl or water container that the Fountain is placed in are cleaned periodically. To clean your
fountain, drain of all water and disassemble. Use a mild soap and a soft cloth to clean the parts of your Fountain.
CLEANING THE WATER PUMP’S PARTS
The impeller inside of the Water Pump is what pushes water up through your Fountain, allowing you to enjoy the soothing sounds and wonderful sights of your Fountain. After long periods of usage, this
part will need to be cleaned to make sure your Fountain runs optimally.
Step 1: Remove the front panel of the Water Pump by grabbing the sides of the front panel and pulling it off the unit.
Step 2: Remove the impeller chamber cover. This is tightly fitted but will come off.
Step 3: Remove the impeller from its chamber.
Step 4: Rinse the impeller until all debris has been removed.
Step 5: Re assemble in reverse order.
PRIMING THE WATER PUMP
If you find the Water Pump is running, but water is not
flowing from your Fountain, you can try priming the Water
Pump:
Turn off Fountain, grab both sides of the Fountain and
quickly shake your Fountain for ten seconds. This is to
dislodge any air bubbles that may be caught in your Water
Pump. Press the button to turn on your Fountain. Water
should be flowing from the top of your Fountain. If water is
not flowing, press and hold button for over 2 seconds
again to turn off your Fountain, and repeat the step above.
WATER PUMP CONNECTION
If your Water Pump becomes disconnected from the Water
Tube inside of the Fountain or if the Water Tube gets
disconnected from the Battery Compartment, go to the
Assembly Section to reconnect the Water Pump.
Made in China | Designed in the USA
Santee, California 92071 | World Wide Patents Pending | Email: [email protected] | On the web: www.berninifountains.com
Facebook & Pinterest: Bernini Fountain Company | Instagram: @berninifountains Twitter: @yrdllc
© Yeiser Research & Development, LLC; 2019. All rights reserved.
Please read first before returning:
Please call us for assistance at [phone] or email us at [email protected]. Our Customer Care Department is available: Monday - Friday 8:30am to 4:00pm PST,
11:30am to 7:00pm EST. If you have any questions regarding assembly, parts or operation, please visit our website at www.berninifountains.com. You will find instructional videos on how to
assemble and operate your fountain and keeps you up to date on our newest products. You can also email us with any questions you have. This product comes with a one year limited warranty
against materials and workmanship.
LIMITED ONE YEAR WARRANTY
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This product has a one year limited warranty on all materials and workmanship.
Bernini® warrants the original purchaser of this product that the product will be free from manufacturing defects in workmanship and material for a period of one (1) year from the date of original
purchase. If within one (1) year this product fails due to defect in material or workmanship, Bernini® will repair, replace or supply any defective part at their option. The purchaser must contact
Bernini® and provide a description of the defective part; including digital pictures if requested, with this original purchase documentation as validation of warranty coverage. This warranty does not
cover or apply to: (a) damage to the product due to misuse, mishandling, and or abuse; (b) products not used in accordance with instructions; (c) product not assembled or installed according to
instructions; and (d) normal wear and tear. Call us for assistance at [phone] or you can email or mail us at: 9545 Pathway Street, Santee, CA 92071, customercar[email protected],
Our Customer Care Department is available: Monday - Friday 8:30am to 4:00pm PST / 11:30am - 7:00pm EST
IMPORTANT BATTERY SAFETY INSTRUCTIONS:
PROPOSITION 65 WARNING: This product can expose you to chemicals including lead and lead compounds which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www. P65Warnings.ca.gov.
WARNING: When using electric devices, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following:
WARNING: 1. Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery can explode in a fire. Check with municipal codes in your area for possible special disposal
instructions.
2. If liquid leaks from the battery cell, discontinue use immediately and dispose of properly.
3. Use only 4-1.5V AA Cell Batteries.
4. Do not attempt to disassemble, remodel or destroy the batteries, as it may cause battery leakage, fire, or bursting; and could also create sulfuric acid spills from the battery resulting in possible burns to
person and damage to the immediate environment.
5. Never dispose of batteries in the garbage. Disposal of batteries in the garbage is unlawful under state and federal environmental laws and regulations. Always take used batteries to your local battery-re-
cycling center.
Maria 3-in-1 Bird Feeder, Fountain & PlanterTM

OWNERS MANUAL
Figure 1 Figure 2 Figure 3 Figure 4
Figure 5 Figure 6 Figure 7 Figure 8
Figure 10
Assembly Of Bird Feeder:
6.
STEP
Figure 9
Top Hieght
Adjustment Bottom Hieght
Adjustment
Top Height
Adjustment Bottom Height
Adjustment
Top Height
Adjustment
Bottom Height
Adjustment
Top Height
Adjustment
Bottom Height
Adjustment
Figure 11 Figure 12
Figure 14
Figure 13 Figure 15 Figure 16
In this step you will install the 3 Bird Feeder Covers into the Base. These 3 Bird Feeder Covers install over the 3 holes in the base and enable you to ll the area with bird seed
once the fountain is completely assembled (Figure 1-4).
Note: Be sure to place the Base of your fountain on a at, rm surface. The 3 Bird Feeder Covers will install in the 3 areas marked with the arrows. All 3 covers are exactly the same.
Insert Inner Water Bowl (Figure 5-7).
Insert the fully assembled Fountain Tower into the center of the Inner Water Bowl. There are two height options for the fountain (See Diagram 1a, Figure 9-10 and Figure11-12
of step 7 ). To lower the height, align the feet of the Fountain Base to the bottom of the Inner Water Bowl. To raise the Fountain height, align the feet to the raised step on the
Inner Bowl. Make sure the Fountain Tower is secure before proceeding to the next step.
Fill Inner Water Bowl with water until it reaches the minimum water level ring on the Fountain Tower (see Diagram 1a and Figure 11).
Add bird seed to the Bottom Bowl (Figure 12). Do not remove the Inner Water Bowl while there is bird seed in the Bottom Bowl (Figure 13).
Insert the Wire Cable into the hole located on the side of the Bottom Bowl. Thread the other end of the Wire Cable through the loop and connect it to the Hook (Figure 14-16).
Repeat this step for the other two Wire Cables (Figure 16).
Maria 3-in-1 Bird Feeder, Fountain & PlanterTM

OWNERS MANUAL
Figure 14
Figure 13 Figure 15 Figure 16
Figure 1 Figure 2 Figure 3 Figure 4
Figure 5 Figure 6 Figure 7 Figure 8
Figure 10
Assembly of Planter
7.
STEP
Figure 9 Figure 11
High Setting Low Setting
Figure 12
Take out Inner Water Bowl, remove any bird feed if converting from a bird feeder, remove the three Bird Feeder Covers in the Base (Figure 1-7) and reinsert the Inner Water
Bowl (Figure 6). Please Note: Please remove the packing material inside Fountain Tower that says “REMOVE BEFORE USE”(Figure 7).
Add soil and plants to the Base (arrows in Figure 13). Do not remove the Water Bowl while there is soil and plants in the Base.
Insert the fully assembled Fountain Tower into the center of the Inner Water Bowl. There are two height options for the fountain (See Diagram 1a and Figure 9 and 10 of this step
and 9-10 of step 6). To lower the height, align the feet of the Fountain Base to the bottom of the Inner Water Bowl. To raise the Fountain height, align the feet to the raised step on
the Inner Water Bowl. Make sure the Fountain is secure before proceeding to the next step.
Fill Inner Water Bowl with water till it reaches the minimum water level ring on the Fountain Base(Figure 11 and Diagram 1a).
Add soil to the Base. Do not remove the Inner Water Bowl while there is soil in the Bottom Bowl (Figure 13).
Insert the Wire Cable into the hole located on the side of the Base. Thread the other end of the Wire Cable through the loop and connect it to the Hook (Figure 14-16).
Repeat this step for the other two Wire Cables (Figure 16).
TM