Halsey Taylor 4705 User manual

PAGE 1 97799C (Rev. K - 09/17)
4705 FR FTN
Halsey Taylor Owners Manual
Freeze Resistant Wall Mounted Steel Fountain
Halsey Taylor Fountains are among the easiest to install Fountains on the market today. To assure you install
these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL,
AND OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future
reference. This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s) contains
the Freeze Resistant Package(s) HTFRB1 that are installed on an interior heated wall. The interior space must
maintain a minimium temperature of 50° F (10° C). Refer to the Freeze Resistant Package for the rough-in
dimensions for installation.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM
THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
INSTALLER

PAGE 297799C (Rev. K - 09/17)
4705 FR FTN
11"
279mm
12" 305mm MAX. WALL THICKNESS
7 1/4"
184mm
12 1/8"
308mm
23 13/16"
605mm
9 3/8"
239mm
29 3/16" 741mm
30 7/8"
784mm
1 1/2"
38mm
6 1/4"
159mm
12 1/2" 318mm
FINISHED FLOOR
D
C
B
A
4705 FREEZE RESISTANT STEEL FOUNTAIN
MOUNTING HOLE AND ACCESS HOLE LAYOUT
LEGEND A = MOUNTING HOLE LOCATIONS (4), (1/2" DIA. BOLTS NOT PROVIDED). B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY TUBE. C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE. D = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE.
FIG. 1

PAGE 3 97799C (Rev. K - 09/17)
4705 FR FTN
4705 FREEZE RESISTANT STEEL FOUNTAIN
ROUGH-IN DRAWINGS
FIG. 2
27" 686mm
ADA
REQUIREMENT
34" 863mm
35 13/16"
909mm
14" 356mm
10 7/8"
277mm
12" 305mm
MAX. WALL THICKNESS
2 5/8"
67mm
3 5/8"
92mm
1/4"
6mm
3 1/2"
89mm
19" 483mm
13 11/16"
348mm
14 11/16"
373mm
18 3/16"
462mm
29 1/8"
740mm
FINISHED FLOOR
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1 and ADA (Framing shown for reference only). 2. Remove bottom cover from fountain and save screws. 3. Install the fountain using bolts and washers (not provided). Tighten securely. 4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide. 5. Install freeze-resistant box - see box instructions. 6. Replace bottom cover.

PAGE 497799C (Rev. K - 09/17)
4705 FR FTN
FIG. 3
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play
FIG. 4
FIG. 5
FIG. 7
FIG. 6

PAGE 5 97799C (Rev. K - 09/17)
4705 FR FTN
FIG. 8 FIG. 9
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the
interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed
mounted. If recess mounted the surface of the cover must be ush with the interior wall surface. The package is
furnished with screws for mounting the cover to the box. If the box is recess mounted, do not fasten the top and
bottom of the cover to the box. Use the holes on the front only.
1. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall). The
adjustment nuts should be in the middle of threaded area on the operating cable. See Figure 3. Create a loop in
the cable and thread the free end of the cable through the wall into the freeze resistant box.
2. Connect free end of operating cable to the valve-operating bracket in the freeze resistant box.
3. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 4.
4. Connect water line from fountain bubbler into freeze resistant box. he connection to the box uses a quick
connect water tting. Position the water line, in the fountain, to drain back into interior mounted box. Any water
left standing, in the exterior line, can freeze. See Fig. 6.
To insert tubing, push tube straight into tting until it reaches a positive stop. To remove tubing from the ttings,
relieve water pressure, push in on dark gray collar while pulling out on the tubing. See Figure 9.
5. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure 1 for component positions.
Inline strainer must be used on the inlet water line. See Fig. 8.
Start-up
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze
resistant package. Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper
valve operation. If the system is too tight the valve will stay in the on position creating constant water ow. Too
much free play will result in non-operation of the valve with the push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is
actuated.
5. After cable system is adjusted properly stuff exible insulation into any openings between the outside wall and
the interior box.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and
fountain(s).
1/4" O.D. TUBE
WATER INLET
NOTE: WATER FLOW DIRECTION
BUILDING WATER
INLET
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
SERVICE STOP
(NOT FURNISHED)
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE.