BERNSTEIN 805 User manual

ASSEMBLY INSTRUCTIONS - IV / 2018
IN-WALL SYSTEM 805
for wall-wc with ushplate

2
In-wall system 805
CONTENT OF DELIVERY:
Item Description Indication Quantity
Rubber seal Ø 110 1
Straight ush
pipe 1
Waste seal 1
Eccentric
pipe 1
Rubber seal 1
Full ush air
hose transparent 1
Half ush air
hose blue 1
Absorbing
panel 1
Flush pipe 1
Rubber seal
for the ush
pipe
Ø 60 1
Rawl plug 8 x 40 2
Screw ST4,8 x 45 2
Item Description Indication Quantity
Rawl plug SX10 Ø 6-8 2
Screw ST6,8 x 67 2
Washer Ø 22 x 2,0 2
M12 Bolt 2
Screw cover 2
M12 Nut 2
big Washer Ø 32,5 x 2,5 2
Rubber bolt 2
Screw cover 2
Stainless
steel bolt 2
Washer Ø 11 x 1,2 2

3
ITEMS INCLUDED IN DELIVERY:
Aluminium frame
Lever
Water cistern Lower half frame Drainage pipe
Flush plate Screw set
Glass panel Flush valve Inlet valve

4
In-wall system 805
Product type: Wall-hung toilet installation system
Model: 20981 (black) and 20982 (white)
Required room temperature: 3 – 40° C
Water supply pressure: 0,07 – 0,75 MPa
Water temperature: 4 – 35° C
Protection class: IPX4
Dimension: 1003,5 x 483 x 108 mm
TECHNICAL SPECIFICATIONS:
TECHNICAL DRAWINGS - Water inlet and waste system:

5
INSTALLATION OF THE SANITARY MODULE:
Insert the drainage pipe into the pre-drilled drainage hole
on the wall.
1
Remove the upper cover (1) and the support and
the support tube (2).
Bracket on the
back wall
2a
2b
Place the sanitary module on the wall and fasten
the drainage pipe (1) with the clamp (2).

6
In-wall system 805
3
4
Using the given openings - four on the wall, two on the
oor - mark the drill holes with a pin (3).
Open the clamp and remove the sanitary
module from the wall (4).

7
5
6
Drill the holes using the markers.
The depth of the drill holes must be greater than the length
of the dowels (see the diameter in the drawing (5)).
Insert the rawl plugs into the corresponding holes (6).
Return the sanitary module
to the correct wall position (7).

8
In-wall system 805
7
8
Now x the unit to the wall tightening the screws in
the corresponding rawl plugs (8) and use the bolts to
secure the feet on the oor.
Connect the tube with the support (1)
and the corresponding valve on the
wall (2 + 3).

9
9
Open the shut-off valve on the inlet water pipe (4) to check the function.

10
In-wall system 805
Bracket glass panel
(4 pieces)
10
Attach the glass panel to the aluminum
frame of the sanitary module (1).
Push it down (2) so the glass panel mounts
snap into the frame mounts.
11

11
Now push the locks into the holding
frame (3) to x the pusher plate.
Mount the retaining frame (1) from the inside and the
pusher plate (2) from the front into the glass panel.
Holding frame of
the pusher plate
Pusher plate
12
13

12
In-wall system 805
blue air hose
transparent air hose
half ush mark
full ush mark
Fix the air hoses as indicated in the above drawing.
Frontal upper cover
Replace the top cover on the sanitary module.
Reference line
Flexible clips
on the cover
Fixed connector
on the side
The exible clips must be
clamped on the connector.
The upper cover is positioned between the wall and
the frontal cover, please note that this cover should
be perfectly aligned – left and right - as indicated in
the above drawing.
14
15

13
Please follow the following steps (16-18) after installing your wall-hung toilet
Draw a mark on the straight ush pipe and on the waste pipe (1).
16
Cut the ush pipe and the waste pipe (2).
File the edge of the pipes 3). Add silicon oil (4).

14
In-wall system 805
17
Fix the bolts on the unit (1)
and the absorbing panel (2).
18
Fix the waste pipe
to the unit (3).
Fix the ush pipe
to the wall-hung toilet (4).
Install the toilet
to the sanitary module (5).

15
19
Cut off the protruding surfaces (6) of the absorber plate.
20
Test the half and full ush functions (7).

16
In-wall system 805
MAINTENANCE:
1.1 How to remove the inlet valve
Lift the upper cover (1). Turn off the stop valve (2) on the exible hose.
Disconnect the hose and the valve (3). Remove the inlet valve pulling it upwards (4).

17
1.2 Adjustment and cleaning of the inlet valve
Lift the oat (1) upwards to increase the waterow or
downwards to reduce it.
Remove the stop valve (2+3) and clean it et nettoyez-la (4).

18
In-wall system 805
1.3 Installing the inlet valve
Follow the 1-3 steps on the drawings.

19
2.1 Removing the ush valve
blue air hose
transparent
air hose
Disconnect the air hoses (1).
Remove the lever (2).

20
In-wall system 805
Clamps of the suspension device.
After having opened the hanger locks (3), lift the ush valve upwards (4).