Better Bathrooms Sahara BeBa-27962 User manual

Multi-person assembly
Tools required
We always recommend using professional
tradespeople to install your product
V1_10.11.20
BeBa_27962, BeBa_27963, BeBa_27964, BeBa_27965,
BeBa_27966, BeBa_27967, BeBa_27968, BeBa_27969，
BeBa_27970
Sahara Towel Radiator
Please note: Image is for illustrative purposes only and may differ slightly to the
actual product

2
Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern
to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So,
you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The Sunday Times Fast Track 100.
We hope your new product exceeds your highest expectations. However, if you
experience any problems, please:
call our friendly UK call centre on 0330 390 3062 (9am-7pm Monday to Friday, or
10am-4pm Saturday and Sunday), or
send us a message via [email protected].uk
Important information
Please read these instructions thoroughly and retain for future reference
Manufactured to BS EN 442-1 Radiators and convectors
Please ensure that the product is checked for damage prior to installation, any
damage reported after installation will not be covered.
The pipework must be flushed out to remove any debris which can affect the
function of this product.
A corrosion inhibitor should be used in your installation.
BTU & Wattage info-
Product Code BTU Wattage
BeBa_27962 747 219
BeBa_27963 904 265
BeBa_27964 914 268
BeBa_27965 1102 323
BeBa_27966 1697 497
BeBa_27967 1041 305
BeBa_27968 1199 351
BeBa_27969 1356 397
BeBa_27970 1508 442

3
Parts
A. 1 x Radiator
B. 1 x Air Vent (Bleed Valve)
C. 1 x Blanking Cap
D. 4 x Wall plug
E. 4 x Wall Bracket
F. 4 x Washer
G. 4 x Wall screw
H. 4 x Rail Bracket
I. 4 x Bracket Screw
J. 4 x Connecting Screw
Please note that Parts are for illustrative purposes only and may differ slightly to
the actual product
Tools required
Spanner
Flathead screwdriver
Philips screwdriver
Tape measure
Drill and 8mm drill bit
Spirit Level
Pencil
Sealing tape

4
Installation
Please note: Before starting any installation, turn off the water supply.
Please note: Before commencing any installation, the desired location should be checked
before drilling, that no pipes or wires can be damaged.
First, prepare the water supply pipes to match up with the towel radiator and valve
dimensions being used. Fit the radiator valve tail and nut into the towel rail (not supplied)
(at both sides) and using sealing tape, tighten into position, then follow the installation
below.
1. Fit the blanking cap and air vent in the top of the rail, (add a little sealer tape to
secure) and tighten using the spanner, be sure not to overtighten.
2. The rear of the towel rail has four location holes to fix the brackets. Measure the
distance between all the location holes and mark these on the wall in the required
location, use a spirit level to ensure these are horizontally and vertically aligned.

5
3. Using the drill and 8mm drill bit, drill into the marked positions then insert the wall
plugs and tap flush to the finished wall surface.
Please note: If drilling into a tile, it is recommended to tape the wall to prevent the drill
from slipping.
4. Position the wall brackets and screw into place using the screws provided (securing
each with a washer) with the Philips screwdriver.
5. Next, proceed to fix the rail brackets to the rear of the radiator and screw into place
using the screws provided with the Philips screwdriver.

7
6. Align and push the rail brackets on the radiator onto the wall brackets secured to
the wall. Secure the two together with the connecting screws provided (insert
through the slot in the bracket) and tighten using the Philips screwdriver, be sure
not to overtighten.
Please note: You may need two people to connect the radiator, depending on the
model purchased.
7. Finally, fit the radiator valves to the pipework and connect to the radiator valve tail
and tighten all connections.
IMPORTANT! The product is supplied un-filled.
The rail should be filled with a water (80%) and glycol (20%) mixture if NOT being
connected to the central heating system, also allow 5% air gap.
After installation
After the above installation, turn on the water supply and using the flathead
screwdriver, open the air vent via the central screw, open the inlet valve and let the
water rush into the radiator. Check all connections for leaks.
Once water overflows from the air vent, this means that there will be no air bubbles
present.
Use a screwdriver to close the air vent and then the radiator is ready to use.
Cleaning
This radiator is made from steel with a painted finish. To maintain the surface of your
product (especially when subjected to steam or splashes), wipe with a clean damp cloth
and wipe dry.
Do not use abrasive cleaning agents or materials which can strip and scratch the surface;
the use of these agents or materials can invalidate your guarantee.
It is recommended to wipe and dry on a regular basis.