Better Bathrooms BeBa 25980 User manual

Product
BeBa_25980 - Empire Freestanding Bath Mixer
•Single-person assembly
•Tools required
•We always recommend using professional
tradespeople to install your product V1_09/9/2021

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern
to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So,
you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The Sunday Times Fast Track 100.
We hope your new product goes above and beyond your expectations. However, should
any problems occur, please:
•log in to your account and contact our customer services team via your self-serve
portal –betterbathrooms.com/CustomerAccount/Login
•contact us via betterbathrooms.com/content/contact-us
Important information
•Please read these instructions thoroughly and retain for future reference
•Installation must be carried out in compliance with The Water Fittings Regulations
and Scottish Water Byelaws.
•The system must be flushed prior to installation
•Minimum and Maximum working pressure : 1 - 5 bar
•Pressures must be equal for optimum performance
•Please do not connect hot and cold water supply lines in reverse. This could result
in hot water flowing from cold line and cause scalding.
•The feed-water temperature of water shall not exceed 85°C.
Exceeding 85°may cause scalding, the service life of faucets might be shortened,
or the faucet might be damaged.
•After installation, please make sure the faucet is securely mounted and checked for
leaks.

Parts / Diagrams
No
Part
Description
No
Part Description
1
Lever
14
Standing pipe
2
Screw
15
O-ring
3
Handle
16
Inlet pipe
4
Screw
17
O-ring
5
Cap
18
O-ring
6
Dome
19
Base
7
Locknut
20
Screw
8
Cartridge
21
Steel gasket
9
Screw
22
Fixed seat
10
O-ring
23
Cover template
11
Spout
24
Plug
12
Aerator
25
Floor screw set
13
Body
26
Body
27
Aerator key
Dimensions

Tools required
•Spanner
•Drill and bit
•Hammer
Installation
Mark out the fixing positions on the flooring
basing on the body and drill four holes. Fix the
floor screws into the holes.
Fix the G3/4 connectors to inlets of the body.
Push the body over floor screws and fasten with
steel gasket and nut. Connect the body with hot
(Left) and cold (right)water pipes using thread
seal tape.

Remove the screws on the cover template with
allen key, and take out the cover template and
plug.
Fasten the fixed seat with the body by fixing
screws.
Slide down the base until it reaches the floor.
Waterproof adhesive is recommended to be
applied.
Turn on water supply and check for leaks.

Operation
Troubleshooting
Issues
Inspection Item
Poor water flow
•Is there blockage within the filter mesh on
aerator
•Was the system flushed prior to installation
•Is the mixer cartridge free from debris
Water leak
•Is there damage or dirt within the O-rings of the
cartridge
•Is there damage or dirt with the rubber washers
in the of aerator
•Is the locknut on top of cartridge fully tightened
Handle loose
•Is the screw inside the handle fully tightened
•Is the locknut on top of cartridge fully tightened
Body loose
•Is the floor-mounting kit underneath fully
tightened

Maintenance
Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do
not use any abrasive cleaning agents or materials. If any harsh chemicals come into
contact with the surface of the product, rinse and wipe clean immediately.