Better Bathrooms BeBa 26360 User manual

Dual Function Shower Head
BeBa_26360
Please note: Image is for illustrative purposes only and may differ slightly to the
actual product
•Single-person assembly
•Tools required
•We always recommend using professional
tradespeople to install your product V2_10.9.20

2
Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern
to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So,
you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The Sunday Times Fast Track 100.
We hope your new product exceeds your highest expectations. However, if you
experience any problems, please:
•call our friendly UK call centre on 0871 244 0935 (9am-7pm Monday to Friday, or
10am-4pm Saturday and Sunday), or
•send us a message via [email protected]
Important information
•Please read these instructions thoroughly and retain for future reference.
•Manufactured to BS EN1112 Shower outlets for sanitary tapware.
•Power Rating 3.2V via a Hydro powered motor
Parts
1. Shower head
2. 1/2" Threaded Connector
3. Rubber Seal
4. Pipe Fitting - 1/2" female (Not supplied)
5. Allen key
Tools required
PTFE tape

3
Installation
Please note: The pipework and connection method should be prepared within the wall
and hole created to accept the 1/2" threaded connector
Recommended method is to secure the arm to a wall elbow (both not supplied) which has
been fixed rigidly within the wall the proceed as below.
1. Remove the screw from the top of the shower head using the Allen key provided,
and keep in a safe place for later.
2. Apply PTFE tape to the threaded connector which will go into the wall, then connect
the threaded connector to the pipe fitting and turn until a seal is created.

4
3. Fit the rubber seal to the end of the threaded connector into the rear of the shower
head. Once fully fitted, re-fit the screw and tighten using the Allen key provided,
ensuring that the head is level. Silicone can be applied between the shower and the
wall to prevent water from passing behind the head.
Please note: Once installation is completed, turn on the water supply and check for any
leaks
Operation
To change the water flow from the shower head, place your finger over the sensor on the
underside of the shower head (indicated by a green light) for 2-3 seconds, to change back
,carry out the same process.

5
Troubleshooting
Poor flow from shower head
1. This can be caused by poor water flow to the shower head, check the flow to the
shower head.
2. There may be a blockage in the rain section of the shower head, clean the shower
head.
Maintenance
•Remove the shower head and turn on the mixer. Check the flow of water, and if this
is poor, it is not an issue with the shower head, and further investigation is required.
Example: insufficient pressure in the system or blockage in the mixer or pipework.
•Rub the rubber nozzles on the rain section with your finger to remove any blockage
then turn on the shower, but do not shower immediately after cleaning, allow the
shower to run for 20 seconds to clear away ant debris.
•Replace the shower head if the issue is not a pressure issue, blockage in the mixer
and the shower head has been cleaned.
Cleaning
To maintain the surface finish of your product, wipe clean after every use, using a clean
damp cloth, a mild detergent mixture can be used. Do not use abrasive cleaning agents or
materials on the product surface.
If any harsh chemicals come into contact with the surface of the product during bathroom
cleaning, rinse off immediately, wipe clean and dry.
Recycling facilities are now available for all customers at which you can deposit your old electrical products.
Customers will be able to take any old electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the recycling process, so please be
considerate when depositing your equipment. Please contact the local council for details of your local
household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the Reach Regulations
(EC) 1907/2006. In accordance with Article 59 of the same regulation the following substances are
contained within the product at permitted levels: Lead & Cadmium.
As a responsible manufacturer the regulations are monitored to ensure continued compliance. Further
information can be provided upon request.