Better Homes and Gardens BH17-021-399-04 User manual

PB 1
model# BH17-021-399-04
model# BH17-021-399-03
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
gray
ivory
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
BEDFORD COFFEE TABLE

2
TOP PANEL
SIDE ASSEMBLY [X2]
BOTTOM PANEL
BOTTOM RAIL [X2]
TOP RAIL [X2]
A
B
C
D
E
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Flat Head Screwdriver Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Lock Washer
x4
3. Cam
x16
4. M6x32mm Bolt
x4
1. Wood Dowel
x28
2. Cam Bolt
x16
6. Washer
x4

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
9. 15mm Pan Head
Screw
x12
7. Allen Wrench
x1
8. Angle Iron
x4

5
1 2
3 4 5
180º
4
HOW TO USE THE CAM LOCK SYSTEM

6
x6 x4 x4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4 x2 x2
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x2 x2 x2
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

8 9
x6 x4 x4
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

10
x10 x4
x4
x1
x4
x4
x4
STEP 5
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
4. M6x32mm
Bolt
7. Allen
Wrench
6. Washer5. Lock
Washer
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

10 11
x12 x4
STEP 6
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
9. 15mm Pan
Head Screw
8. Angle Iron
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
70 lbs. / 31.5 kg.
50 lbs. / 22.7 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

PB 1
model# BH17-021-399-04
model# BH17-021-399-03
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
gris
marl
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
MESA PARA CAFÉ
BEDFORD
Instrucciones de Ensamble

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
PANEL SUPERIOR
ENSAMBLE DEL LADO [X2]
PANEL INFERIOR
RIEL INFERIOR [X2]
RIEL SUPERIOR [X2]
A
B
C
D
E
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza Plana Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Arandela Fijodora
x4
3. Leva
x16
4. M6x32mm Perno
x4
1. Clavija de Madera
x28
2. Tornillo de Leva
x16
6. Arandela
x4

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
9. 15mm Tornillo de
Cabeza de Noria
x12
7. Llava Allen
x1
8. Soporte
x4

5
1 2
3 4 5
180º
4
COMO USAR EL SISTEMA FIJADOR DE LEVA

6
x6 x4 x4
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x4 x2 x2
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8
x2 x2 x2
PASO 3
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva