Steelcase Turnstone Elan TS52071 User manual

Page 1 of 4
939503209 Rev B
Élan™Table Desk R
©2001 Steelcase Inc.
Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
TS52071, TS52072, TS52073, TS52074 and TS52075
Please save these instructions for use with assembly
of 1/4 Round Bridge, Corner Bridge and Return.
24” X 48” Table Desk
TS52071
30” X 60” Table Desk
TS52074
30” X 30” Table Desk
TS52072
30” X 48” Table Desk
TS52073 30” X 72” Table Desk
TS52075

Page 2 of 4
939503209 Rev B
1. unpack the components
Unpack the parts and lay them out on a carpeted surface
(to avoid scratches). Make sure you have all the items
shown below.
2. lay worksurface down
Lay the desk worksurface upside down with the holes facing
up. Insert four (4) screws into the pilot holes on the ends of
the worksurface and screw half-way in.
modesty panel
end legs
table top
wire covers
END legs (legs with 28” foot
and 1 outside and 1 inside wire
cover) are used for all outside
leg positions on 30” deep
worksurfaces.
MID legs (legs with 23” foot
and 2 inside wire covers) are
used for all internal leg positions,
example: desks with bridges
attached. (Note: stand alone
desks do not need a mid leg).
RETURN legs (legs with 23”
foot and 1 outside and 1 inside
wire cover) are used for all
outside leg positions on 24”
worksurfaces.
ATTACHMENT SLOT
3. attach legs to desk worksurface
Position legs over top of screws and slide leg toward
front of desk to engage screws into slots.
end leg - 28”
mid leg - 23”
return leg - 23”

Page 3 of 4
939503209 Rev B
4. secure legs to worksurface.
Place screwdriver into access
hole over scr ews and drive
scr ews until tight. Leave one
of the legs loose until modesty
panel is attached. This will be
tightened later .
5. attach modesty panel to legs
Slide the hooks on the ends of
the modesty panel into the slots
on both legs (they fit tightly in
the slots) and push the modesty
panel down until it touches the
worksurface.
6. attach modesty panel to
worksur face. Attach the modesty
panel to the underside of the
worksurface using the scr ews as
shown. Return to step 5 to
tighten the two scr ews in the leg
that were left loose.
7. attach wire covers to legs
Snap the wir e covers into the leg
frames (if not alr eady attached),
by placing the edge of the wir e
covers into the groove in the legs
and gently pr essing the covers
until they snap into place.
8. flip the desk over. Use two
people to flip the desk over.
Adjust the glides to compensate
for uneven floors.
That’s it!
4 5
67

Page 4 of 4
939503209 Rev B
Maintenance
Furniture Protection
Desk pads and coasters should be used to help
protect the surface against dents, scratches,
moisture and hot or cold liquids. Objects should be
lifted, not pulled or pushed across the surface, to
avoid scratching the furniture. Felt or leather pads
should be used on the bottom of office equipment or
accessories.
Cleaning Melamine Surfaces
For all laminate tops, painted and plated metals, and
plastics: Wiping with a damp cloth will remove
general soiling and water-borne stains. If needed,
use a hard-surface, all purpose cleaner. Some oil-
borne stains may require the use of a dry-cleaning
fluid or naphtha. To fill scratches in wood grain
laminate tops, use an oak, walnut, or mahogany
putty stick (available at paint supply and hardware
stores).
Cleaning Hardware
Metal finishes should be cleaned with water and/or a
non-abrasive cleaner. Household cleaners for wood
may be used, but usually warm water is sufficient.
Wipe the hardware with a damp, soft cloth, or a cloth
to which you have sparingly applied the cleaner.
Wipe dry with a clean cloth.
Moving Furniture
When moving desks short distances, make sure that
the legs are secured to the body of the unit. Move
the unit by picking it up and carefully placing it into
the new position. The desk should not be dragged
on the floor. When moving long distances, legs
should be detached from the desk body.