OAKWORKS Mattes Chair User manual

Phone: [phone] www.oakworks.com
Mattes Chair
by OAKWORKS®
USA
ASSEMBLED BY
HAND IN THE
OPERATION INSTRUCTIONS

1. Unfasten leg strap. (Figure 2)
2. Unlock 2 leg safety clamps. (Figure 3)
3. Lift legs and put horizontal leg tube into the safety
clamp nest. (Figure 4) Note that the height is adjustable
depending on nest chosen. Feet should easily touch the
ground and thighs at 90º or sloping slightly downward.
Choose the middle height for the average. (Figure 5)
4. Securely lock both safety clamps making sure lock is fully
seated. (Figure 6) CAUTION: Leg safety clamps must
always be locked when in use.
5. Turn chair over and stand it on the floor. (Figure 7)
6. Raise backrest into position and adjust backrest height
using knob on the rear of the backrest. Note: there is a
handle for moving the chair around the room. (Figure 8)
7. The optional pad can be installed on the rear of the backrest
by placing the pad pocket over the backrest. (Figure 9)
1. Remove the optional pad from the box (if ordered).
2. Remove the carry strap from the box.
3. Remove the chair from the box & place it on a protected
floor or table with the legs up. (Figure 1)
UNPACKING
page 1
OPERATION INSTRUCTIONS
Mattes Chair by OAKWORKS®
CAUTION
MAXIMUM WORKING LOAD RATING
300 LBS. (136 KG)
Figure 1
CHAIR SET UP
Figure 2 Figure 3
Figure 4 Figure 5
Figure 6 Figure 7
Figure 9
Figure 8

page 2
1. Folding the chair is basically the reverse of the set up.
2. Remove pad (if necessary), fold down backrest, turn chair over
Be sure the Velcro®straps are inside of the legs (Figure 14)
Unlock leg safety clamps, lift tube out of nest and fold
legs with two legs pointing one way and two legs pointing the
opposite way. Re-lock leg safety clamps. Wrap Velcro®
leg strap around legs first then around the chair to
secure using Velcro®attachment. (Figure 15, 16 & 17)
CHAIR FOLDING
1. Attach chair carry shoulder strap to the two chair hooks
at the rear of the seat. (Figure 18)
2. Lift chair and place strap for most comfortable length.
(Figure 19)
CHAIR TRANSPORTATION
Figure 19
Figure 18
CLEANING & MAINTENANCE
8. The seat belt strap is used to stabilize the person in the chair
during side-bending motions. A Velcro®system allows you to
adjust the fit for each client. (Figure 10)
9. Finger grips located under the seat are used to help the client
stabilize their trunk, or aid in rotation during various stretches
and movements. (Figure 11 & 12)
10. The horizontal bar is grasped by the client to help them stretch
forward. (Figure 13)
Figure 10 Figure 11
Figure 12 Figure 13
Figure 14 Figure 15
Figure 16 Figure 17
CLEAN your upholstered items when needed using a mild
solution of 4:1 diluted non-alcohol cleaner such as Formula
409®, Fantastik®, or Green Windex®
DISINFECT your fabric with Protex, MadaCide,
MadaWipe, Accell TB, Virox®(Canada), or a diluted 1/10
bleach solution. Dry immediately after cleaning to remove
excess cleaning solution.
DO NOT use citrus based cleaners or other strong cleaners,
such as alcohol, acetone, higher concentrations of bleach
or other products that contain high concentrations of these
substances.
DO NOT expose the fabric to temperatures below 32°F/0°C
or above 95°F/35°C.
DO NOT expose the fabric to direct sunlight, adhesives,
liquids, or abrasive materials.
FAILURE TO FOLLOW RECOMMENDATIONS WILL
VOID THE WARRANTY ON THE FABRIC.

Manual Part Number MMMNML0001
Revision date: 10.17.12
Edition 1 May, 2010
Printed in English
Printed in USA
CONTACT INFORMATION:
Oakworks®Inc.
923 East Wellspring Road
New Freedom, PA 17349
Toll Free (USA only): 800-916-4613
Phone: [phone]
FAX: [phone]
www.oakworks.com
Mattes Chair
by OAKWORKS®
OPERATION INSTRUCTIONS
USA
ASSEMBLED BY
HAND IN THE