Better Homes and Gardens BH46-084-099-54 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-09-24 Rev. 0001-A Factory: HESLTD
Steele Organizer with Drawers
Stock # BH46-084-099-54
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOGUE: Steele Organizer with Drawers (BH46-084-099-54)
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 30 lb. (13.6 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 200 lb. (90.7 kg)

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the fireplace.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) C- Right Side Panel (Qty. 1)
D- Bottom Panel (Qty. 1) E- Upper Fixed Shelf (Qty. 1) F- Lower Fixed Shelf (Qty. 1)
G- Upper Divider Panel (Qty. 2) H- Drawer Divider (Qty. 1) I- Middle Divider Panel (Qty. 2)
J- Bottom Long Support (Qty. 2) K- Bottom Short Support (Qty. 2) L- Back Panel (Qty. 1)
M- Drawer Left Side N- Drawer Right Side O- Drawer Back Panel
(Qty.2) (Qty. 2) (Qty. 2)
P- Drawer Bottom Panel Q- Drawer Bottom Support R- Drawer Front
(Qty.2) (Qty. 2) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 12+1 extra) (Qty. 22+1 extra) (Qty. 34+1 extra)
(4) M15 x 60 mm Large Wood Dowel (5) M8 x 60 mm Small Wood Dowel (6) M8 x 30 mm Wood Dowel
(Qty. 8+1 extra) (Qty. 16+1 extra) (Qty. 34+1 extra)
(7) M6 x 30 mm Wood Dowel (8) Ø5/16" x 2-1/4" Bolt (9) Lock Washer
(Qty. 4+1 extra) (Qty. 8+1 extra) (Qty. 8+1 extra)
(10) Flat Washer (11) M4 x 38 mm Screw (12) M4 x 50 mm Screw
(Qty. 8+1 extra) (Qty. 12+1 extra) (Qty. 18+1 extra)
(13) Handle (Qty. 2) (14) Handle Bolt (Qty. 4) (15) Cam Lock Cover (Qty. 4+1 extra)
(16) Plastic Cap (Qty. 4+1 extra) Allen Wrench (1) Glue (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Allen wrench (provided) and Phillips screwdriver and hammer (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw 6 Cam Bolts (3) into the designated small holes on one Drawer Front (R).
3. Connect Drawer Left and Right Side Panels (M and N) to the Drawer Front (R) by engaging two M6 x
30 mm Wood Dowels (7) and four Small Cam Locks (1) (Refer to page 3 on Cam Lock system
operation supplement).
4. Fasten the Drawer Bottom Support (Q) to the Drawer Front (R) with two Small Cam Lock (1).
3
3
3
3
3
17
R
R
M
QN
Small Cam Lock
(6 used in this step)
①
Cam Bolt
(6 used in this step)
③
M6 x 30 mm Wood Dowel
(2 used in this step)
⑦

7
Assembly Instructions
5. Slide the Utility Drawer Bottom Panel (P) into the grooves between the Drawer Side Panels (M and N)
until fully inserted into the Drawer Front (R).
R
M
N
Q
P

8
Assembly Instructions
6. Fasten one Drawer Back Panel (O) to the Drawer Side Panels (M and N) and Bottom Support (Q) with
six 38 mm Screws (11). Make sure that Drawer Bottom Panel (P) fits securely into the groove of the
Drawer Back Panel (O). Tighten all the screws with a Phillips screwdriver.
R
M
N
Q
P
O
11
11
O
R
M
N
11
M4 x 38 mm Screw
(6 used in this step)
⑪

9
Assembly Instructions
7. Turn the assembled drawer upright.
8. Attach the Handle (13) to the outside of the Drawer Front (R) with two Handle Bolts (14).
9. Repeat the same process to assemble the other drawer.
Handle Bolt
(2 used in this step)
⑭
Handle
(1 used in this step)
⑬
13
14
14 RR

10
Assembly Instructions
10. Attach the Bottom Short Supports (K) between the Bottom Long Supports (J) with four 30 mm Wood
Dowels (6).
11. Fasten the previous assembly to the Bottom Panel (D) with eight 30 mm Wood Dowels (6) and twelve
50 mm Screws (12).
6
6
6
6
K
KJ
J12
12
12
12 12
12
12
12 66
6
6
6
6
6
D
K
J
K
J
M8 x 30 mm Wood Dowel
(12 used in this step)
⑥
M4 x 50 mm Screw
(12 used in this step)
⑫

11
Assembly Instructions
12. Securely screw the Cam Bolts (3) into the designated small holes on the Side Panels (B and C), the
Bottom Panel (D) and the Lower Fixed Shelf (F) using a Phillips screwdriver.
Cam Bolt
(22 used in this step)
③
3
BC
F
D

12
Assembly Instructions
13. Attach the Back Panel (L) to the Lower Fixed Shelf (F) with two 30 mm Wood Dowels (6) and four
Large Cam Locks (2) (Refer to page 3 on Cam Lock system operation supplement).
2
2
2
26
6
F
L
Large Cam Lock
(4 used in this step)
②
M8 x 30 mm Wood Dowel
(2 used in this step)
⑥

13
Assembly Instructions
14. Attach the Drawer Divider (H) to the Lower Fixed Shelf (F) with two 30 mm Wood Dowels (6) and two
Large Cam Locks (2).
L
F
H
2
2
6
Large Cam Lock
(2 used in this step)
②
M8 x 30 mm Wood Dowel
(2 used in this step)
⑥

14
Assembly Instructions
15. Attach two Middle Divider Panels (I) to the Lower Fixed Shelf (F) with four 30 mm Wood Dowels (6)
and four 50 mm Screws (12).
M8 x 30 mm Wood Dowel
(4 used in this step)
⑥
6
6
H
L
F
I
12
12
12
I
M4 x 50 mm Screw
(4 used in this step)
⑫

15
Assembly Instructions
16. Attach two Upper Divider Panels (G) and Upper Fixed Shelf (E) to the assembled Middle Divider
Panels (I) with eight 60 mm Small Wood Dowels (5).
55
5
H
F
G
G
E
I
I
L
M8 x 60 mm Small Wood Dowel
(8 used in this step)
⑤

16
Assembly Instructions
17. Attach the Right Side Panel (C) to the Fixed Shelves (E and F) and the Back Panel (L) with five 30 mm
Wood Dowels (6) and six Large Cam Locks (2).
18. Repeat the same procedure to attach the Left Right Panel (B) at the opposite end.
2
2
2
2
2
2
2
2
6
6
6
6
6
H
L
F
E
B
C
6
6
2
Large Cam Lock
(12 used in this step)
②
M8 x 30 mm Wood Dowel
(10 used in this step)
⑥

17
Assembly Instructions
19. Insert four 60 mm Large Wood Dowels (4) into the bottom holes on the Side Panels (B and C) and
insert four 30 mm Wood Dowels (6) into the bottom holes on the Drawer Divider (H) and the Back
Panel (L). Position the Bottom Panel (D) onto the inserted wood dowels and attach to the Back Panel (L)
with four Large Cam Locks (2).
2
2
2
2
4
46
6
6
H
F
B
C
D
6
L
Large Cam Lock
(4 used in this step)
②
M8 x 30 mm Wood Dowel
(4 used in this step)
⑥
M15x 60 mm Large Wood Dowel
(4 used in this step)
④

18
Assembly Instructions
20. Secure the Bottom Panel (D) to the Side Panels (B and C) with four 2-1/4” Bolts (8) and four Washers (9
and 10).
21. Fasten the Bottom Panel (D) to the Drawer Divider (H) with two 50 mm Screws (12).
B
C
H
F
D12
8
9
10
M4 x 50 mm Screw
(2 used in this step)
⑫
2-1/4” Bolt
(4 used in this step)
⑧
Lock Washer
(4 used in this step)
⑨
Flat Washer
(4 used in this step)
⑩

19
Assembly Instructions
22. Insert eight 60 mm Small Wood Dowels (5) into the top holes of Upper Divider Panels (G) and insert four
60 mm Large Wood Dowels (4) into the top holes on the Side Panels (B and C).
23. Position the Top Panel (A) onto the inserted wood dowels and attach it into place with four 2-1/4” Bolts (8)
and four Washers (9 and 10).
24. Cover the countersunk holes on the Top Panel (A) by inserting four Plastic Caps (16). Gently tap the Plastic
Cap with a rubber mallet to ensure they are fully seated.
2-1/4” Bolt
(4 used in this step)
⑧
Lock Washer
(4 used in this step)
⑨
Flat Washer
(4 used in this step)
⑩
M15x 60 mm Large Wood Dowel
(4 used in this step)
④
M8 x 60 mm Small Wood Dowel
(8 used in this step)
⑤
A
B
G
G
C
8
9
10 16
5
4
Plastic Cap
(4 used in this step)
⑯

20
Assembly Instructions
25.
Ask for assistance to stand the unit upright.
26.
Insert the assembled drawers into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (B
and C) all the way forward (including ball bearing cart). Then align the Slide Runners on the assembled
drawer with the Slide Tracks and push the drawer carefully inside until it stops.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step. If you need to
remove the drawer, please pull the drawer all the way out, then simultaneously push the plastic release
lever of the ball bearing slides up on one side and down on the other side, and then pull it completely
out.
27. Insert the Cam Lock Covers (15) to conceal the cam locks underneath the Upper Fixed Shelf (E).
B
C
E
M
N
N
15