Better Homes and Gardens FLYNN CREDENZA BH16-084-699-01 User manual

PB 1
model# BH16-084-699-01
model# BH47-021-199-12
model# BH47-021-199-13
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
FLYNN CREDENZA
pecan
smoke gray
white

2
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BOTTOM PANEL
BACK PANEL
PARTITION PANEL
FOOT [X4]
FIXED SHELF
DRAWER FRONT [X2]
LEFT DRAWER SIDE [X2]
RIGHT DRAWER SIDE [X2]
DRAWER BACK [X2]
DRAWER BOTTOM [X2]
DOOR
A
B
C
D
E
F
G
H
I
J
K
L
M
N
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. 15mm Pan Head
Screw
x21
6. 19mm Pan Head
Screw
x1
3. C a m
x16
4. Flat Head Screw
x16
1. Wood Dowel
x16
2. Cam Bolt
x16

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
9. Wall Anchor
x1
10. Wall Screw
x1
11. C a m C o v e r
x1
7. Wall Strap
x1
8. Washer
x2

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x2 x2 x2
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
nished edge

6 7
x2 x2 x2
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
nished edge

8
x6 x6 x1x6
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
4. Place cover over visible hole
1. Wo o d
D o w e l
2. Cam Bolt 11. C a m
Cover
3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
nished edge

8 9
x6 x6 x6
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wo o d
D o w e l
2. Cam Bolt 3. C a m
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x21
STEP 5
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
5. 15mm Pa n
Head Screw
hole for anti-tip strap
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.

10 11
STEP 6
1. Install door as shown.

12
STEP 7
1. Fix door in place as shown.

12 13
x16
x2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 8
4. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

14
STEP 9

14 15
x1x1x1x1x2
6
7
8
9
8
10
STEP 10
7. Wall Strap6. 19mm Pan
Head Screw
10. Wa l l
Screw
9. Wa l l
Anchor
8. Washer
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

16
100 lbs. / 45.4 kg.
45 lbs. / 20.4 kg.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

PB 1
model# BH16-084-699-01
model# BH47-021-199-12
model# BH47-021-199-13
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
TRINCHADOR FLYNN
Instrucciones de Ensamble
nuez
gris humo
blanco

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
PANEL INFERIOR
PANEL POSTERIOR
DIVISOR
PATA [X4]
REPISA FIJA
CAJÓN FRONTAL [X2]
CAJÓN LATERAL IZQUIERDO [X2]
CAJÓN DERECHO [X2]
CAJÓN POSTERIOR [X2]
CAJÓN INFERIOR [X2]
PUERTA
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Tornillo Corto de
Cabeza de Noria
x21
6. Tornillo Largo de
Cabeza de Noria
x1
3. L e v a
x16
4. Tornillo de Cabeza
Plana
x16
2. Tornillo de Leva
x16
1. Clavija de Madera
x16

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
9. Taquete de Pared
x1
10. Tornillo de Pared
x1
11. Cubierta del Tornillo
x1
8. Arandele
x2
7. Cincha de Pared
x1