Better Homes and Gardens WILLOW BH17-084-699-01 User manual

PB 1
model# BH17-084-699-01
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
WILLOW 2 TONE BUFFET

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
ADJUSTABLE SHELF [X2]
PARTITION PANEL
REAR RAIL
FRONT RAIL
A
B
C
D
E
F
G
CENTER FOOT
FOOT [X4]
BOTTOM PANEL
BACK PANEL
LEFT DOOR
RIGHT DOOR
H
I
J
K
L
M
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Hammer Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Shelf Pin
x8
3. 38mm Flat Head
Screw
x7
4. Pan Head Screw
x22
1. Wood Dowel
x20
2. 25mm Flat Head
Screw
x12
6. Wall Anchor
x1

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
9. Washer
x2
7. Truss Head Screw
x1
8. Wall Strap
x1

4 5
x4 x4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 1
1. Wood
Dowel
2. 25mm
Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6
STEP 2

6 7
x2 x2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 3
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
Dowel
2. 25mm
Flat Head
Screw

8
x8 x6
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 4
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
Dowel
3. 38mm
Flat Head
Screw
front

8 9
x6 x6
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 5
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
Dowel
2. 25mm
Flat Head
Screw

10
x22
STEP 6
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
4. Pan Head
Screw
hole for anti-tip strap
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.

10 11
x8
STEP 7
1. Insert shelf supports into desired holes. Dierent holes accommodate dierent shelf heights.
2. Angle shelves to t between the rails and set on top of shelf supports.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
5. Shelf Pin

12
STEP 8

12 13
STEP 9

14
STEP 10

14 15
STEP 11

16
x1x1x1x1
x2
6
3
9
78
9
STEP 12
7. Truss
Head Screw
3. 38mm Flat
Head Screw
8. Wall Strap
9. Washer
6. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

16 17
For use with televisions weighing
50 pounds (22.7 kg) or less. Use with
heavier televisions may result in
instability causing tip over resulting
in death or serious injury.
Use of anti-tip restraints may only
reduce, but not eliminate, the risk
of tip-over.
! WARNING
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
100 lbs. general use /
50 lbs. television use
35 lbs. per shelf
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH17-084-699-01
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
BUFFET DE 2 TONOS
WILLOW
Instrucciones de Ensamble

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Martillo Destornillador Phillips
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
REPISA AJUSTABLE [X2]
DIVISOR
RIEL TRASERO
RIEL FRONTAL
A
B
C
D
E
F
G
PATA CENTRAL
PATA [X4]
PANEL INFERIOR
PANEL POSTERIOR
PUERTA IZQUIERDO
PUERTA DERECHO
H
I
J
K
L
M

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Pasador Para Repisa
x8
3. 38mm Tornillo De
Cabeza de Plana
x7
4. Tornillo de Cabeza de
Noria
x22
1. Clavija de Madera
x20
2. 25mm Tornillo De
Cabeza de Plana
x12
6. Taquette de Pared
x1