Better Homes and Gardens KENDARA BH18-021-199-01 User manual

PB 1
model# BH18-021-199-01
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
rich espresso
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
KENDARA CONSOLE TABLE

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BACK PANEL
SHELF
DRAWER FRONT
A
B
C
D
E
F
DRAWER LEFT SIDE
DRAWER RIGHT SIDE
DRAWER BACK
DRAWER BOTTOM
DRAWER SUPPORT
G
H
I
J
K
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Hammer Flat Head Screwdriver Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
3. Cam
x11
4. Cam Cover
x4
1. Wood Dowel
x16
2. Cam Bolt
x11
5. Flat Head Screw
x5
6. Allen Wrench
x1

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
8. Handle Bolt
x4
7. Handle
x2
12. Washer
x6
9. Small Bolt
x4
10. Large Bolt
x4
11. Lock Washer
x4

54
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
15. Truss Head Screw
x1
16. Wall Screw
x1
13. Wall Anchor
x1
14. Wall Strap
x1

6
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6 7
x2 x2
STEP 1
1. Screw-In cam bolts must be screwed down ush.
2. Refer to page 6 for instructions on how to use the cam lock system.
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x3 x2
x2
x2
x2
x1
x2
STEP 2
1. Wood
Dowel
2. Cam Bolt
10. Large
Bolt
3. Cam
11. Lock
Washer
6. Allen
Wrench
12. Washer
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
4. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x3 x2
x2
x2
x2
x1
x2
STEP 3
1. Wood
Dowel
2. Cam Bolt
10. Large
Bolt
3. Cam
11. Lock
Washer
6. Allen
Wrench
12. Washer
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
4. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x4x4 x1
STEP 4
9. Small Bolt6. Allen
Wrench
1. Wood
D o w e l
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x6 x5x5 x4
x5
STEP 5
1. Wood
Dowel
2. Cam Bolt 3. Cam 4. Cam Cover
5. Flat Head
Screw
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
4. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
x4 x2
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 6
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
8. Handle
Bolt
7. Handle

12 13
x1x1x1x1
x2
13
16
15
12
12
14
STEP 7
15. Truss
Head Screw
16. Wall
Screw
14. Wall
Strap
12. Washer
13. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

14
50 lbs. / 22.7 kg.
40 lbs. / 18.1 kg.
25 lbs. / 11.3 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH18-021-199-01
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
café
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
CONSOLA KENDARA
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
PANEL POSTERIOR
REPISA
CAJÓN FRONTAL
A
B
C
D
E
F
CAJÓN LATERAL IZQUIERDO
CAJÓN LATERAL DERECHO
CAJÓN POSTERIOR
CAJÓN INFERIOR
SOPORTE DE CAJÓN
G
H
I
J
K
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza PlanaMartillo Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
3. Leva
x11
4. Cubierta del
Tornillo
x4
2. Tornillo de leva
x11
1. Clavija de Madera
x16
5. Tornillo de Cabeza
Plana
x5
6. Llave Allen
x1

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
8. Perno de Agarradera
x4
7. Agarradera
x2
12. Arandela
x6
9. Perno Pequeño
x4
10. Perno Largo
x4
11. Arandela Fijadora
x4

54
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
15. Tornillo de Cabeza
Redonda
x1
16. Tornillo de Pared
x1
14. Cincha de Pared
x1
13. Taquete de Pared
x1

6
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA