Better Homes and Gardens BH46-084-899-02 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-05-05 Rev. 0001-A Factory: KONRIC
Steele TV Stand
Stock # BH46-084-899-02
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Steele TV Stand (BH46-084-899-02)
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted slightly,
turn the appropriate screw as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
FITS UP TO MOST 80” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM LOAD 30 lb. (13.6 kg)
2
3

3
Important
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw Cam Bolt into the pre-drilled small holes on panel. Connect both panels together; making
sure Cam Bolt goes into pre-drilled hole on the end of panel with Cam Lock.
2. Insert Cam Lock into pre-drilled large hole on panel. Make sure arrow on Cam Lock is pointed toward
Cam Bolt.
3. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten Cam Lock clockwise.
4. Plug Cam Cap into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the TV console.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Bottom Panel (Qty. 1) C- Base Front Stretcher (Qty. 1)
D- Base Back Stretcher (Qty. 1) E- Base Side Stretcher (Qty. 2) F- Left Side Panel (Qty. 1)
G- Partition Panel H- Right Side Panel I- Left Door
(Qty. 1) (Qty. 1) (Qty. 1)
J- Right Door ( Qty. 1) K- Adjustable Shelf ( Qty. 1) L- Back Panel ( Qty. 2 )
M- Drawer Front ( Qty. 2) N- Drawer Back Panel ( Qty. 2) O- Drawer Left Side ( Qty. 2)
P- Drawer Right Side Q- Drawer Bottom Support R- Drawer Bottom Panel
( Qty. 2) ( Qty. 2) ( Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 10+1 extra) (Qty. 12+1 extra) (Qty. 22+1 extra)
(4) M6 x 30 mm Wood Dowel (5) M8 x 30 mm Wood Dowel (6) M3.5 x 15 mm Washer Head Screw
(Qty. 22+1 extra) (Qty. 18+1 extra) (Qty. 48+2 extra)
(7) M4 x 38 mm Screw (8) M4 x 50 mm Screw (9) M3 x 15 mm Pan Head Screw
(Qty. 12+1 extra) (Qty. 12+1 extra) (Qty. 4+1 extra)
(10) Magnetic Catch (11) Corner Connector (12) Shelf Pin
(Qty. 2) (Qty. 4) (Qty. 4+1 extra)
(13) Cam Lock Cover (14) Handle (15) 22 mm Handle Bolt
(Qty. 4+1 extra) (Qty. 4) (Qty. 8)
(16) M3.5 x 12 mm Screw (17) Triangle Metal Plate (18) Floor Leveler (19) M10 x 40 mm Wood Dowel
(Qty. 8+1 extra) (Qty. 2) (Qty. 2) (Qty. 12+1 extra)
Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 1) (Qty. 1) (Included in plastic bag)
Tools required: Phillips screwdriver and hammer (not provided).