Better Homes and Gardens Oxford Square Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 16086
Date 2015-04-24 Rev. 1 Factory: KONRIC
Oxford Square Accent Table
Stock # BH45-021-199-03
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED:
/
/

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 16086
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Oxford Square Accent Table (BH45-021-199-03)
MADE IN CHINA
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace
it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your
highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY
,
CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 10 lb. (4.53 kg)
MAXIMUM LOAD 50 lb. (22.6 kg)

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 16086
Important
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making sure
the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and
tighten the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XXFINAL
12 43

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 16086
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1) B- Bottom Panel (1) C- Left Front Leg (1)
D- Left Back Leg (1) E- Right Front Leg (1) F- Right Back Leg (1)
G- Left Side Panel (1) H- Right Side Panel (1) I- Back Panel (1)
J- Top Crossbar (1) K- Middle Crossbar (1) L- Drawer Front (1)
M- Drawer Back Panel (1) N- Drawer Left Side (1) O- Drawer Right Side (1) P- Drawer Bottom Panel (1)

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 16086
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 20 mm Wood Dowel
(24+1 extra) (24+1 extra) (2+1 extra)
(4) M8 x 30 mm Wood Dowel (5) M10 x 40 mm Wood Dowel (6) #8 x 1” Screw
(18+1 extra) (4+1 extra) (2+1 extra)
(7) #8 x 1-1/4” Screw (8) #3 x 5/8” Screw (9) Metal Bracket
(4+1 extra) (8+1 extra) (4)
(10) Drawer Knob (1) (11) 3/4” Knob Bolt (1) Glue (1)
Flat Tip Screwdriver (1) Touch-up Pen (1)
Tools required: Flat Tip screwdriver (provided), Phillips screwdriver and hammer (not provided).

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 6 Factory No. 16086
Utility Drawer Assembling
1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Place the Drawer Front (L) on a level and protective surface with the holes facing up. Securely screw
four Cam Bolts (2) into the designated small holes, as shown in the illustration.
3. Attach the Drawer Side Panels (N and O) to the Drawer Front (L) by engaging four Cam Locks (1)
(Refer to page 3 on Cam Lock system operation supplement). Make sure that the grooves face inward
and line up with each other.
L
2
N
O
1
2
L
Cam Bolt
(4 used in this step)
②
Cam Lock
(4 used in this step)
①

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 7 Factory No. 16086
Utility Drawer Assembling
4. Slide the Drawer Bottom Panel (P) into the grooves between the Drawer Side Panels (N and O) until
fully inserted into the Drawer Front (L). Make sure the finished surface will face up.
N
O
L

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 8 Factory No. 16086
Utility Drawer Assembling
5. Fasten the Drawer Back Panel (M) to the Drawer Side Panels (N and O) using four 1-1/4” Screws (7).
Make sure that the Drawer Bottom Panel (P) fits securely into the groove of the Drawer Back Panel (M).
Tighten all the screws with a Phillips screwdriver.
7
7
PN
O
PN
O
M
1-1/4” Screw
(4 used in this step)
⑦

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 9 Factory No. 16086
Utility Drawer Assembling
6. Attach the Drawer Knob (10) to the outside of the Drawer Front (L) using the provide 3/4” Bolt (11).
11
10
N
O
L
Drawer Knob
(1 used in this step)
⑩
3/4” Knob Bolt
(1 used in this step)
⑪

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 10 Factory No. 16086
Assembly Instructions
7. Securely screw the Cam Bolts (2) into the designated small holes on the Table Top (A) and four Legs (C,
D, E and F), as shown in the illustration.
2
A/C/D/E/F
A
C
DF
E
Cam Bolt
(20 used in this step)
②

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 11 Factory No. 16086
C
D
G
4
1
4
1
E
F
H
4
1
4
1
Assembly Instructions
8. Insert two M8 x 30 mm Wood Dowels (4) into the middle holes of the Left Side Panel (G) at both ends.
Attach the Left Side Panel (G) between the Left Front and Back Legs (C and D) by engaging four Cam
Locks (1). As shown above. Make sure that the Cam Locks will face inward and the slides opening will
point towards the front of the unit.
9. Repeat last step to combine the Right Side Panel (H) and Right Legs (E and F) together.
Cam Lock
(8 used in this step)
①
M8 x 30 mm Wood Dowel
(4 used in this step)
④

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 12 Factory No. 16086
C
D
G
K
I
4
1
1
4
Assembly Instructions
10. Insert one M8 x 30 mm Wood Dowel (4) into the inner end hole of the Modesty Panel (I) and attach it
to the Left Back Leg (D) by using two Cam Locks (1). As shown above. Make sure that the Cam Locks
face inward and the cam bolt holes for Table Top (A) will point upward.
11. Fasten the Middle Crossbar (K) to the assembled left side frame using one M8 x 30 mm Wood Dowel (4)
and one Cam Lock (1), as shown. Ensure the Cam Lock will point towards the bottom of the unit.
M8 x 30 mm Wood Dowel
(2 used in this step)
④
Cam Lock
(3 used in this step)
①

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 13 Factory No. 16086
C
D
B
4
4
Assembly Instructions
12. Attach the Bottom Panel (B) to the Left Legs (C and D) using two M8 x 30 mm Wood Dowels (4), as
shown. Make sure that the pilot holes will point towards the bottom of the unit.
M8 x 30 mm Wood Dowel
(2 used in this step)
④

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 14 Factory No. 16086
Assembly Instructions
13. Repeat the same procedure to attach the assembled right side frame at the opposite end.
B
K
I
4
4
4
4
1
1
E
F
H
M8 x 30 mm Wood Dowel
(4 used in this step)
④
Cam Lock
(3 used in this step)
①

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 15 Factory No. 16086
Assembly Instructions
14. Fasten the Bottom Panel (B) to four Legs (C, D, E and F) by attaching four Metal Brackets (9) over the
pilot holes at the joints, using two 5/8” Screws (1) per metal bracket. As shown.
B
C
D
E
F
B
C/D
E/F
8
8
9
Metal Bracket
(4 used in this step)
⑨
#3 x 5/8” Screw
(8 used in this step)
⑧

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 16 Factory No. 16086
A
J
3
6
Assembly Instructions
15. Fasten the Top Crossbar (J) to the Table Top (A) using two 20 mm Wood Dowels (3) and two 1”
Screws (6). As shown. Make sure the finished edge on the Top Crossbar (J) points towards the front of
the unit.
1” Screw
(2 used in this step)
⑥
M8 x 20 mm Wood Dowel
(2 used in this step)
③

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 17 Factory No. 16086
Assembly Instructions
16. Stand the assembled unit upright.
17. Insert one M10 x 40 mm Wood Dowel (5) into the top hole of each Leg and insert two M8 x 30 mm
Wood Dowels (4) into the top inner holes of each Side Panel (G and H) and the Back Panel (I). As
shown. DO NOT insert the wood dowels into the cam bolt holes.
18. Position the Table Top (A) onto the inserted Wood Dowels (4 and 5). Fasten the Table Top (A) in place
by engaging six Cam Locks (1). As shown.
A
C
DG
E
H
I
A
C/D
E/F
G/H/I
5
4
1
M8 x 30 mm Wood Dowel
(6 used in this step)
④
M10 x 40 mm Wood Dowel
(4 used in this step)
⑤
Cam Lock
(3 used in this step)
①

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 18 Factory No. 16086
Assembly Instructions
19. Insert the assembled drawer into frame to finish the assembly. Simply push the ball bearing cart all the
way to the end of the slides (on both sides), and then align the slide runners on the drawer with the slide
tracks on the unit. Push it carefully inside until it stops.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step.
A
NO
L

Stock # BH45-021-199-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 19 Factory No. 16086
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an
inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may
create spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that
you call a professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and
helpful tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!

IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
Oxford Square Accent Table (BH45-021-199-03)
*BH45-021-199-03-1-TT Table Top *BH45-021-199-03-17-DBP Drawer Bottom Panel *BH45-021-199-03-2-BP Bottom Panel *BH45-021-199-03-18-CL Cam Lock *BH45-021-199-03-3-LFL Left Front Leg *BH45-021-199-03-19-CB Cam Bolt *BH45-021-199-03-4-LBL Left Back Leg *BH45-021-199-03-20-M8x20WD M8 x 20 mm Wood Dowel *BH45-021-199-03-5-RFL Right Front Leg *BH45-021-199-03-21-M8x30WD M8 x 30 mm Wood Dowel *BH45-021-199-03-6-RBL Right Back Leg *BH45-021-199-03-22-M10x40WD M10 x 40 mm Wood Dowel *BH45-021-199-03-7-LSP Left Side Panel *BH45-021-199-03-23-1S #8 x 1” Screw *BH45-021-199-03-8-RSP Right Side Panel *BH45-021-199-03-24-1 1/4S #8 x 1-1/4” Screw *BH45-021-199-03-9-DS Drawer Slides *BH45-021-199-03-25-5/8S #3 x 5/8” Screw *BH45-021-199-03-10-BP Back Panel *BH45-021-199-03-26-MB Metal Bracket *BH45-021-199-03-11-TC Top Crossbar *BH45-021-199-03-27-DK Drawer Knob *BH45-021-199-03-12-MC Middle Crossbar *BH45-021-199-03-28-3/4KB 3/4” Knob Bolt *BH45-021-199-03-13-DF Drawer Front *BH45-021-199-03-29-FTS Flat Tip Screwdriver *BH45-021-199-03-14-DBP Drawer Back Panel *BH45-021-199-03-30-G Glue *BH45-021-199-03-15-DLS Drawer Left Side *BH45-021-199-03-31-TUP Touch-up Pen *BH45-021-199-03-16-DRS Drawer Right Side *BH45-021-199-03-CH Complete Hardware