Better Homes and Gardens Upholstered Side Wing Chair User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 17137
Date 2015-06-12 Rev. 1 Factory: FUKIFU
Upholstered Side Wing Chair
Stock # BH15-084-399-01
# BH15-084-399-02
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 17137
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will
repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture
product is designed to meet your highest expectations. We guarantee that you will immediately
see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary
from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
1. Maximum load weight on chair is 136 kg / 300 lb.
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM RECOMMENDED W
EIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE
MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING
POSSIBLE INJURY.

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 17137
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A - Backrest (1)
B - Seat Frame with Cushion (1) C - Front Leg (2)
(1) Ø5/16” x 2-1/4” Bolt (6+1 extra) (2) Ø5/16” x 3-1/4” (4+1 extra)
(3) Lock Washer (10+1 extra) (4) Flat Washer (10+1 extra)
5 mm Allen Wrench (1) Touch-up Pen (1)
Tools required: Allen wrench (provided).

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 17137
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Lay the Backrest (A) on a smooth and protective surface with the threaded inserts facing up.
3. Take the Seat Frame (B) and unfold the bottom flap down. Position the Seat Frame (B) onto the middle
rail of the Backrest (A) with the end dowel fully inserted. Insert and screw four 3-1/4” Bolts (2) with the
Lock Washers (3) and Flat Washers (4) through the rear corner blocks and screw into the threaded inserts
on the Backrest.
4. Secure the Seat Frame (B) to the Backrest (A) by inserting two 2-1/4” Bolts (1) with the Washers (3 and 4)
through the pre-drilled holes on the rear rail of the Seat Frame.
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
B
A
4
1
3
B
4
2
3
A
2-1/4” Bolt
(2 used in this step)
①
3-1/4” Bolt
(4 used in this step)
②
Lock Washer
(6 used in this step)
③
Flat
Washer
(6 used in this step)
④

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 17137
Assembly Instructions
5. Fit the Front Legs (C) to the front corners of the Seat Frame (B). Insert four 2-1/4” Bolts (1) with the
Washers (3 and 4) through the drilled holes on the corner blocks and screw into the threaded inserts on
the Front Legs.
NOTE: DO NOT fully tighten all the bolts until the chair has been adjust and level all the legs so that
they do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
6. Stand the assembled unit upright on a flat surface. Press down the Seat Cushion (B) to even all legs. Now,
tightly fasten all bolts with the provided Allen wrench. To complete the assembly, fold the bottom flap up
and attach to the bottom side of the Seat Frame (B) using the Velcro straps.
3
4
1
B
C
B
C
C
A
2-1/4” Bolt
(4 used in this step)
①
Lock Washer
(4 used in this step)
③
Flat
Washer
(4 used in this step)
④

Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 6 Factory No. 17137
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 Stains or marks from crayons or ink markers will be difficult to remove.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!

IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
Upholstered Side Wing Chair (BH15-084-399-01)
*BH15-084-399-01-1-CB Chair Backrest *BH15-084-399-01-2-SFWC Seat Frame with Cushion *BH15-084-399-01-3-FL Front Leg *BH15-084-399-01-4-2 1/4B Ø5/16” x 2-1/4” Bolt *BH15-084-399-01-5-3 1/4B Ø5/16” x 3-1/4” Bolt *BH15-084-399-01-6-LW Lock Washer *BH15-084-399-01-7-FW Flat Washer *BH15-084-399-01-8-M5AW 5 mm Allen Wrench *BH15-084-399-01-9-TUP Touch-up Pen *BH15-084-399-01-CH Complete Hardwaere

IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
Upholstered Side Wing Chair (BH15-084-399-02)
*BH15-084-399-02-1-B Backrest *BH15-084-399-02-2-SFWC Seat Frame with Cushion *BH15-084-399-02-3-FL Front Leg *BH15-084-399-02-4-2 1/4B Ø5/16” x 2-1/4” Bolt *BH15-084-399-02-5-3 1/4B Ø5/16” x 3-1/4” Bolt *BH15-084-399-02-6-LW Lock Washer *BH15-084-399-02-7-FW Flat Washer *BH15-084-399-02-8-M5AW 5 mm Allen Wrench *BH15-084-399-02-9-TUP Touch-up Pen *BH15-084-399-02-CH Complete Hardwaere