Better Homes and Gardens FLYNN BH47-084-199-03 User manual

PB 1
model# BH47-084-199-03
model# BH47-084-199-04
model# BH47-084-199-05
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
pecan
smoke gray
white
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
FLYNN BOOKCASE

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
SHELF A [x3]
SHELF B
DRAWER FRONT
BOTTOM ASSEMBLY
BACK PANEL
FOOT [x4]
A
B
C
D
E
F
G
H
I
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

32
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Magnet Catch
x2
3.Cam
x28
4. Hardware Cover
x16
1. Wooden Dowel
x32
2. Cam Bolt
x28
6. Pan Head Screw
x4
7. Flat Head Screw
x14

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
12. Washer
x2
10. Wall Anchor
x1
11. Wall Screw
x1
8. Left Hinge
x1
9. Right Hinge
x1
13. Truss Head Screw
x1
14. Wall Strap
x1

5
1 2
3 4 5
180º
4
HOW TO USE THE CAM LOCK SYSTEM

6
x4 x1 x1
STEP 1
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
7. Flat Head
Screw
8. Left Hinge 9. Right
Hinge

6 7
x12 x10 x10
x2
x2
x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wooden
Dowel
2. Cam Bolt 3. Cam
5. Magnet
Catch
4. Hardware
Cover
6. Pan Head
Screw

8
x10 x10 x10 x2
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wooden
Dowel
2. Cam Bolt 3. Cam 4. Hardware
Cover

8 9
x4 x4 x4 x4
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wooden
Dowel
2. Cam Bolt 3. Cam 4. Hardware
Cover

10
x6 x4 x4 x4
STEP 5
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wooden
Dowel
2. Cam Bolt 3. Cam 4. Hardware
Cover

10 11
STEP 6

12
x4 x4
STEP 7
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
4. Hardware
Cover

12 13
x6
STEP 8
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

14
x1x1x1x1
x2
10
11
12
13
12
14
STEP 9
13. Truss
Head Screw
11. Wall
Screw
14. Wall
Strap
12. Washer
10. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

14 15
40 lbs. / 18.1 kg.
40 lbs. / 18.1 kg.
40 lbs. / 18.1 kg.
40 lbs. / 18.1 kg.
40 lbs. / 18.1 kg.
40 lbs. / 18.1 kg.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

PB 1
model# BH47-084-199-03
model# BH47-084-199-04
model# BH47-084-199-05
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
nuez
gris humo
blanco
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
LIBRERO FLYNN
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
PANEL DE REPISA A [x3]
PANEL DE REPISA B
CAJÓN FRONTAL
ENSAMBLE INFERIOR
PANEL POSTERIOR
PATA [x4]
A
B
C
D
E
F
G
H
I
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

32
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. I m á n
x2
3. L e v a
x28
4. Cubierta del Tornillo
x16
6. Tornillo de Cabeza de
Noria
x4
7. Tornillo de Cabeza
Plana
x14
2. Tornillo de Leva
x28
1. Clavija de Madera
x32

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
12. Arandela
x2
10. Taquete de Pared
x1
11. Tornillo de Pared
x1
13. Tornillo de Cabeza
Redonda
x1
14. Cincha de Pared
x1
9. Bisagra Derecha
x1
8. Bisagra Izquierda
x1

5
1 2
3 4 5
180º
4
COMO USAR EL SISTEMA FIJADOR DE LEVA