Better Homes and Gardens Maddox Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-07-05 Rev. 0001-A
Maddox Crossing Dresser
Stock # BH16-084-099-70
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
1. This product is for indoor domestic use only.
2. Please read the Assembly Instructions prior to assembling this product.
3. To avoid damage, assemble the product on a non-abrasive surface such as a carpet surface.
4. Refer to your assembly manual for maximum weight capacities. Load drawers from the bottom to the top.
Place heavier items in lower drawers. Unload the drawers from the top to the bottom before moving the
furniture.
5. Do not push furniture, especially on carpeted floor. Have someone help you lift the item and place it in its
new location.
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Maddox Crossing Dresser
MODEL # BH16-084-099-70
MADE IN MALAYSIA
Please make sure you have all parts before beginning assembly. Please wait until all steps are completed
before tightening bolts. We recommend using two people for assembly.
G E N E R A L I N F O R M A T I O N & T I P S
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 30 lb. (13.6 kg)
MAXIMUM LOAD 100 lb. (45.3 kg)

3
FURNITURE TIPPING RESTRAINT
YOUNG CHILDREN CAN BE SERIOUSLY INJURED BY TIPPING FURNITURE.
YOU MUST INSTALL THE TIPPING RESTRAINT HARDWARE WITH THE UNIT
TO PREVENT THE UNIT FROM TIPPING, CAUSING ANY ACCIDENTS OR
DAMAGE.
THIS HARDWARE, MUST BE PROPERLY INSTALLED (FOLLOW ALL
DIRECTIONS IN ORDER ON THE PLASTIC BAG), TO PROVIDE PROTECTION
AGAINST THE UNEXPECTED TIPPING OF FURNITURE DUE TO IMPROPER
USE.
THE TIPPING RESTRAINTS ARE INTENDED ONLY AS A DETERRENT, THEY
ARE NOT A SUBSTITUTE FOR PROPER ADULT SUPERVISION. THE TIPPING
RESTRAINTS ARE NOT EARTHQUAKE RESTRAINTS. IF YOU WISH TO ADD
THE EXTRA SECURITY OF EARTHQUAKE RESTRAINTS, THEY MUST BE
PURCHASED AND INSTALLED SEPARATELY.
WARNING
Serious or fatal crushing injuries can occur from
furniture tip-over. To help prevent tip-over:
 Install tip-over restraint provided.
 Place heaviest items in the lower drawers.
 Unless specifically designed to accommodate, do not set TVs
or other heavy objects on top of this product.
 Never allow children to climb or hang on drawers, doors, or
shelves.
 Never open more than one drawer at a time.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are
present before beginning assembly.
A- Dresser (Qty. 1)
Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Phillips screwdriver (not provided).

5
DRAWER INSTALLATION
If you need to remove the drawers with ball bearing slides from the unit, please follow the
steps below to prevent any damage to the slides or the drawers.
1. If you need to remove the drawer, please pull the drawer all the way out, then simultaneously
push the plastic release lever of the ball bearing slide up on one side and down on the other side,
and then pull the drawer completely out. See detail A.
2. To place the drawer back, simply push the ball bearing cart all the way to the end of the slides
(in both sides), and align the slide runners on the drawer with the slide tracks on the unit and
push it carefully inside until it stops. See Detail B.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step.