Better Homes and Gardens Canton Dresser BHS336158813014 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-03-10 Rev. 0001-A
Canton Dresser
Stock # BHS336158813014
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Canton Dresser
MODEL # BHS336158813014
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D W E I G H T
L O
A D S
MAXIMUM LOAD 9.1 kg / 20 lb.
MAXIMUM LOAD 45.4 kg / 100 lb.
MAXIMUM LOAD 4.5 kg / 10 lb.
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 4, 5 and 6 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the dowel at least halfway by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
You are now ready to assemble the KD unit.
GLUE
FINAL
1 2 43
13
123

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel B- Fixed Panel
(Qty. 1) (Qty. 1)
C- Bottom Panel D- Bottom Front Skirting
(Qty. 1) (Qty. 1)
E- Bottom Back Skirting F- Left Side Panel
(Qty. 1) (Qty. 1)
G- Right Side Panel H- Lower Partition Panel I- Upper Partition Panel
(Qty. 1) (Qty. 1) (Qty. 2)
J- Left Crossbar K- Right Crossbar L- Back Panel
(Qty. 2) (Qty. 2) (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
M- Small Drawer Front Panel N- Small Drawer Back Panel
(Qty. 3) (Qty. 3)
O- Small Drawer Left Side Panel P- Small Drawer Right Side Panel
(Qty. 3) (Qty. 3)
Q- Small Drawer Bottom Panel R- Large Drawer Front Panel
(Qty. 3) (Qty. 6)
S- Large Drawer Back Panel T- Large Drawer Left Side Panel
(Qty. 6) (Qty. 6)
U- Large Drawer Right Side Panel V- Large Drawer Bottom Panel W- Drawer Bottom Support
(Qty. 6) (Qty. 6) (Qty. 9)

6
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 54+2 extra) (Qty. 35+1 extra) (Qty. 89+4 extra)
(4) M8 x 30 mm Large Wood Dowel (5) M5 x 30 mm Small Wood Dowel (6) M3.5 x 15 mm Screw
(Qty. 38+1 extra) (Qty. 36+1 extra) (Qty. 4+1 extra)
(7) M3.5 x 38 mm Screw (8) M4 x 50 mm Screw (9) M3.5 x 15 mm Washer Head Screw
(Qty. 54+2 extra) (Qty. 6+1 extra) (Qty. 30+1 extra)
(10) M3.5 x 15 mm Pan Head Screw (11) Triangle Metal Plate (12) Floor Leveler
(Qty. 8+1 extra) (Qty. 2) (Qty. 2)
(13) L-shaped Bracket (14) Knob (15) 5/32” x 22 mm Bolt
(Qty. 2) (Qty. 9) (Qty. 9)
Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty.2)
(Qty. 2) (Qty. 1) (Included in plastic bag)
Tools required (not provided): Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill
bit.

7
Assembly Instructions
NOTE: Please do not fully tighten all cam locks and screws until you finish assembling all parts. Once
assembled, go back and fully tighten all cam locks and screws. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (3) into the designated small holes on the Drawer Front Panels (M and R)
using a Phillips Screwdriver.
Small Drawer
x
3
Large Drawer
x
6
③ x 54
M
3
R

8
Assembly Instructions
3. Glue the Small Wood Dowels (5) into the inner holes on the Drawer Back Panels (N and S) and Drawer
Side Panels (O, P, T and U).
NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the
excess glue immediately.
5
5
Small Drawer
x
3
⑤ x 36
Large Drawer
x
6
5
5
5
5
O
N
P
S
T
U
5
5
5
5

9
S
T
U
7
7
Assembly Instructions
4. Attach each Small Drawer Back Panel (N) between the Small Drawer Side Panels (O and P) with four
38 mm Screws (7).
5. Repeat the same procedure to attach each Large Drawer Back Panel (S) between the Large Drawer Side
Panels (T and U).
Grooves line up with each
other and face inward
⑦ x 36
Grooves line up with each
other and face inward
Small Drawer
x
3
Large Drawer
x
6
N
O
P
7
7

10
Assembly Instructions
6. Slide each Small Drawer Bottom Panel (Q) into the grooves on both Small Drawer Side Panels (O and
P) until fully inserted into the Small Drawer Back Panel (N).
7. Repeat the same procedure for the Large Drawer Bottom Panels (V).
Small Drawer
x
3
Large Drawer
x
6
T
U
V
S
O
P
Q
N

11
Assembly Instructions
8. Fasten one Drawer Bottom Support (W) to each Drawer Back Panel (N and S) with two 38mm Screws
(7).
⑦ x 18
The cam mounting holes face outward.
The cam mounting holes face outward.
Small Drawer
x
3
Large Drawer
x
6
W
N
7
Q
W
S7
V

12
Assembly Instructions
9. Position the Drawer Front Panels (M and R) onto the inserted Wood Dowels and fasten it in place by
engaging 6 Small Cam Locks (1). (Refer to page 3 on Cam Lock system operation supplement). Make
sure that the Drawer Bottom Panels (Q and V) fits securely into the groove of the Drawer Front Panels
(M and R).
①
x
5
4
Small Drawer
x
3
Large Drawer
x
6
W
O
P
M
1
1
1
Q
T
U
W
R
1
1
1
V

13
Assembly Instructions
10. Install one Knob (14) to the front of each Drawer Front Panel (M and R) with one 22 mm Bolt (15).
x 9
x 9
Small Drawer
x
3
Large Drawer
x
6
M14
15
R14
15

14
Assembly Instructions
11. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A) and Side Panels
(F and G) using a Phillips Screwdriver.
③ x 22
3
A
GF

15
Assembly Instructions
12. Securely screw the Cam Bolts (3) into the designated small holes on the Fixed Panel (B) and Bottom
Panel (C) using a Phillips Screwdriver.
③ x 9
3
B
C

16
Assembly Instructions
13. Securely screw four Cam Bolts (3) into the designated small holes on both sides of Lower Partition
Panel (H) using a Phillips Screwdriver.
③ x 4
3
HH

17
Assembly Instructions
14. Glue the Large Wood Dowels (4) into the inner holes on the Fixed Panel (B) and Partition Panels (H
and I) as shown.
④ x 16
4
4
B
H
4
4
4
4
4
4
I
I

18
Assembly Instructions
15. Orient and attach the Upper Partition Panels (I) to the Fixed Panel (B) with four 50mm Screws (8).
⑧ x 4
T
h
e roller
s
and
c
u
touts
are or
iented at
the
front side
.
B
I
I
8
8

19
Assembly Instructions
16. Align and attach the Lower Partition Panel (H) to the Fixed Panel (B) by engaging 2 Large Cam Locks
(2).
② x 2
B
H2
2

20
Assembly Instructions
17. Glue the Large Wood Dowels (4) into the inner holes on the Bottom Panel (C) and Bottom Skirtings (D
and E).
④ x 10
4
4
C
E
D
4
4
4
4
4