Better Homes and Gardens MAYA CREDENZA BH47-021-199-16 User manual

PB 1
model# BH47-021-199-16
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
MAYA CREDENZA

2
TOP PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
UPPER PARTITION
FIXED SHELF
LOWER PARTITION
ADJUSTABLE SHELF [X2]
BOTTOM PANEL
A
B
C
D
E
F
G
H
FOOT
LEFT DOOR
RIGHT DOOR
BACK PANEL
I
J
K
L
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Pan Head Screw
x23
3. Cam
x10
4. Flat head screw
x2
1. Wood Dowel
x20
2. Cam Bolt
x10
6. Allen Wrench
x1

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. Wall Anchor
x1
9. Bolt
x8
10. Lock Washer
x8
7. Shelf Pin
x8
8. Cam Cover
x6
12. Wall Screw
x1

54 5
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
15. Washer
x10
13. Truss Head Screw
x1
14. Wall Strap
x1
HARDWARE LIST

1 2
3 4 5
180º
6
HOW TO USE THE CAM LOCK SYSTEM

7
x4 x2 x2 x2
x2
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam 4. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
8. Cam Cover

8
x4 x4 x4 x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam 8. Cam Cover
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

9
x6 x2
x4
x2
x4
x1
x4
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt
9. Bolt
3. Cam
10. Lock
Washer
6. Allen
Wrench
15. Washer

10
x6 x2
x4
x2
x4
x1
x4
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt
9. Bolt
3. Cam
10. Lock
Washer
6. Allen
Wrench
15. Washer

11
x23
STEP 5
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
5. Pan Head
Screw
hole for anti-tip strap
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.

12
x8
STEP 6
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
7. Shelf Pin
1. Insert shelf supports into desired holes. Dierent holes accommodate dierent shelf heights.
2. Angle shelves to t between the rails and set on top of shelf supports.

13
STEP 7

14
STEP 8

15
STEP 9

16
STEP 10

17
x1x1x1x1
x2
11
12
13
15
15
14
STEP 11
13. Truss
Head Screw
12. Wall
Screw
14. Wall
Strap
15. Washer
11. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

18
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
For use with televisions weighing
50 pounds (22.7 kg) or less. Use with
heavier televisions may result in
instability causing tip over resulting
in death or serious injury.
Use of anti-tip restraints may only
reduce, but not eliminate, the risk
of tip-over.
! WARNING
25 lbs. per shelf
90 lbs. general use /
50 lbs. television use
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH47-021-199-16
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
TRINCHADOR MAYA
Instrucciones de Ensamble

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
PANEL SUPERIOR
PANEL DEL LADO IZQUIERDO
PANEL DEL LADO DERECHO
DIVISOR SUPERIOR
REPISA FIJA
DIVISOR INFERIOR
REPISA AJUSTABLE [X2]
PANEL INFERIOR
A
B
C
D
E
F
G
H
PATA
PUERTA IZQUIERDA
PUERTA DERECHA
PANEL POSTERIOR
I
J
K
L