HiB 54500 User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
DIMENSION
Dimension 50: Art No 54500 / Dimension 60: Art No 54600
Dimension 80: Art No 54700
FI#02 023 R201113 Ver No. 1.0 Jan 2021

2
Electrical Safety Information
Warnings for Safe Use
HiB recommends that all electrical bathroom products must be installed
in accordance with current building and wiring regulations.
If in doubt please contact an electrician.
Before drilling ensure that there are no hidden cables or pipes in the wall.
• This product is intended for Domestic Use only.
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• If you give the product to another person, please give them this manual as
well.
• If any modification is made it will invalidate the warranty and may render the
product unsafe.
• This product is IP44 rated and suitable for installation in Zones 2 and Outside
Zones according to the IEEE regulations.
• It is not suitable for use in saunas, steam rooms and shower cubicles.
• Appropriate circuit protection should be available for the product.
• When drilling use appropriate eye protection.
• The use of a Residual Current Device (RCD) is advised for any power tools used
during the installation of this product.
• Take suitable precautions when handling glass.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Always switch off the electrical supply to the product at the mains during
installation and maintenance.
• It is recommended that this product is installed by a person who is able to
meet the level of competence required in order to comply with relevant
regulations. If in doubt consult a qualified tradesperson.
• Do not enter IP44 box unless competent and item is isolated from mains.
• Do not use if glass is broken or unsafe.
• Do not use if any electrical wires appear damaged or degraded.
• Do not overload shelves or unit.
• This product is designed for installation into a brick or masonry block wall,
if mounting onto other substrate ensure appropriate fixing and batons (if
required) are used and the load bearing of the wall is sufficient.
• It is recommended that this product is installed by two people.
• Dispose of packaging in accordance to local authority regulations.
• At end of life dispose of item according to local authority regulations.

3
hib.co.uk
Electrical Information
All installations must comply
with guidelines which are
based on a zonal concept
and must be followed to
ensure the safe installation of
electrical appliances in the
bathroom.
These regulations apply to
domestic installations only.
Installations must be made in
accordance with the current
IEE wiring regulations and
relevant building regulations.
This product is IP44 rated and is suitable for installation in zones: 2& Outside Zone
Wiring Diagram
Fig 1. - Zonal Diagram
What’s in the Box?
• Dimension Cabinet
• Glass shelves
• Mounting bracket
• Fittings pack
live
earth
neutral
MAINS SUPPLY
LUMINAIRE
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Earth is Green and Yellow
Neutral is Blue

4
Tools Required
Figures
Pencil Spirit Level Drill Drill bit Screwdriver
Fig 2. - Hanging Bracket
Fig 3. - Mounting Points Fig 4. - Shelf bracket

5
hib.co.uk
Adjustment
Door Adjustment
Door Removal
Move door(s) up/down
Move door away/towards
the cabinet
Move door(s) left/right

6
Installation
Before installation, ensure the domestic electrical mains supply to which the
cabinet is to be connected is turned off. Before drilling, ensure that there are
no hidden cables or pipes in the wall.
It is recommended that this product is installed by two people.
1. Position the cabinet in a suitable location, according to the zonal diagram Fig.
1, ensuring that the mains supply cable is within reach of the cable connection
point of the cabinet. Carefully mark the desired position of the cabinet using a so
pencil, ensuring it is level.
2. Remove the cabinet from the wall and using a spirit level, mark a horizontal line
below the pencil mark, taking into account the location of the mounting points,
Place brackets on the line and carefully mark the position of the holes using a so
pencil, see Fig. 2.
3. Before drilling, ensure there are no hidden cables or pipes behind the
mounting point. Using a suitable drill bit, drill holes in the marked positions to a
suitable depth.
4. Insert wall plugs level with the surface of the wall. If fitting to a tiled surface,
wall plugs should be inserted below the tile surface to avoid cracking. NB. For
plasterboard walls, specialist fixings should be purchased from any DIY or
hardware store.
5. Fix the brackets to the wall using the screws provided.
6. Temporarily hang the cabinet on the top bracket, see Fig. 3, to mark the
position of the internal fixing hole, then remove the cabinet. Using a suitable drill
bit, drill a hole and insert a wall plug as per stage 3.
7. Connect the cable at the rear of the cabinet to the mains supply cable using a
suitable terminal block (not supplied) according to the wiring diagram on page 3.
10. Rehang the cabinet in position and secure the base of the cabinet with the
supplied screw(s) and screw cap(s).
11. Adjust the shelf supports provided by loosening the securing screw and
slide up or down to the required position inside of the cabinet. Tighten bracket
securing screw when finished. Slide the glass shelf into the brackets when
finished and secure in place by tightening the securing screws, see Fig 4.
12. Switch the mains supply back on.

7
hib.co.uk
Operation
To turn illumination on or off, touch the button on the right side of the cabinet.
The heated pad is only on when the cabinet is illuminated.
Charging Socket(s) and USB
Charger socket(s) are suitable for charging and powering electric razors, trimmers
and toothbrushes. Some cabinets may contain multiple charging sockets. NB. On
first use of the charger socket, inserting the plug may prove to be stiff. Reasonable
force may be required to fully insert the plug. Aer a few uses, stiffness will ease
and the socket will function as normal.
Pairing Device To the Cabinet
• To activate the Bluetooth, turn on cabinet by the sensor located on the side of
the cabinet. The cabinet will give out a tone to confirm it is ready for pairing.
• Activate the Bluetooth on your device*. Refer to the device’s instructions for
details.
• Search for “DIMENSION” and select ‘Pair’ on your device. The cabinet will give
out a tone to confirm successful connection.
• You can now play audio through the Bluetooth cabinet.
• When the cabinet is turned off the connection to the Bluetooth will be lost.
When the cabinet is turned on again it will automatically reconnect to the last
connected device if it is still within range.
• Refer to your device manual for operating controls.
*Only compatible Smart Phones & Bluetooth Devices.

Care
Aftercare
In the unlikely event that this product should fail please contact the retailer
from which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you
regard the following care and cleaning recommendations:
• Avoid leaving excessive standing and surface water on the product for
prolonged periods of time.
• Clean the product with water and a so cloth, a mild detergent may be
used if required. Ensure any excess moisture is removed aer use.
• Do not use abrasive sponges or cleaning agents.
WEEE compliance
Must not be mixed with
general household waste
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN