Better Homes and Gardens BH15-084-899-07 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-10-23 Rev 0001-C
Oxford Square TV Console
Stock # BH15-084-899-07 / BH46-084-899-03
# BH46-084-899-04 / BH46-084-899-05
# BHW-10035 / BHW-10036
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Oxford Square TV Console
MODEL #: BH15-084-899-07/BH46-084-899-03/BH46-084-899-04/BH46-084-899-05 / BHW-10035/ BHW-10036
MADE IN VIETNAM
How to adjust the European adjustable hinges on doors
Shipping may cause doors to become out of alignment. If you find that the doors need to be
adjusted slightly, turn the appropriate screw as illustrated below.
1. TO ADJUST THE DOOR FORWARD OR
BACKWARD.
2. TO ADJUST THE DOOR TO RIGHT OR
TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 50 lb. (22.7 kg)
FITS UP TO MOST 55” DIAGONAL
FLAT PANEL TVs
MAXIMUM LOAD 1
3
5
lb.
(
61
.
2
kg)
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS
COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY. FOR USE WITH
TELEVISIONS WEIGHING 135 LBS (61.2 KG) OR LESS. USE WITH HEAVIER TELEVISIONS MAY RESULT
IN INSTABILITY CAUSING TIP OVER RESULTING IN DEATH OR SERIOUS INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Frame (Qty. 1) C- Right Side Frame (Qty. 1)
D- Bottom Panel (Qty. 1) E- Partition Panel (Qty. 1) F- Center Support with Leveler (Qty. 1)
G- Adjustable Shelf (Qty. 4) H- Left Door (Qty. 1) I- Right Door (Qty. 1)
J- Back Panel (Qty. 1) K- Cable Wheel (Qty. 2) L- Stop Rail (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 12+1 extra) (Qty. 12+1 extra) (Qty. 12+1 extra)
(4) 3/4” Bolt (5) 1-1/2” Screw (6) #5 x 5/8” Screw
(Qty. 4+1 extra) (Qty. 2+1 extra) (Qty. 4+1 extra)
(7) #3 x 5/8” Washer Head Screw (8) Shelf Support (9) Cam Lock Cover
(Qty. 32+1 extra) (Qty. 16+1 extra) (Qty. 18+1 extra)
(10) Magnetic Catch (Qty. 2) (11) Knob (Qty. 2) (12) Knob Bolt (Qty. 2)
Glue (Qty. 1) Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Not included for item (Included in plastic bag)
#BH46-084-899-03 and BHW-10035)
Tools required: Phillips screwdriver and hammer (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Locate the Top Panel (A) with the drilled holes facing up. Align two Magnetic Catches (10) with the
pilot holes on the Top Panel (A) making sure the magnetic plates face the closest edge, then attach the
Magnetic Catches (10) using two #5 x 5/8” Screws (6) per catch.
#5 x 5/8” Screw
(4 used in this step)
⑥
Magnetic Catch
(2 used in this step)
⑩
A

7
Assembly Instructions
3. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), Left and Right
Side Frames (B and C), as shown in the illustration.
Cam Bolt
(12 used in this step)
②
A
B
C
2
A/B/C

8
Assembly Instructions
4. Insert 2 Wood Dowels (3) into the inner holes on the bottom edge of Partition Panel (E). Tap in with a
rubber mallet, if necessary. Make sure that you use a small amount of glue with both ends of all dowels.
NOTE: It is very important to use a small amount of glue on both ends of dowels.
5. Align the inserted Wood Dowels (3) on the Partition Panel (E) with the drilled holes on the Bottom
Panel (D) and press them together. As shown. Make sure that the finished edge of the Partition Panel
(E) points towards the molding of the Bottom Panel (D). Insert two 1-1/2” Screws (5) through the drilled
holes on the Bottom Panel (D) and securely screw into the bottom holes on the Partition Panel (E).
D
E
Wood Dowel
(2 used in this step)
③
1-1/2” Screw
(2 used in this step)
⑤

9
Assembly Instructions
6. Glue four Wood Dowels (3) into the inner holes on both ends of the Bottom Panel (D). DO NOT insert
the Wood Dowels into the Cam Bolt holes.
7. Align the bottom holes on the Left Side Frame (B) with the inserted Wood Dowels (3) on the Bottom
Panel (D) and press them together. Fasten the Left Side Frame (B) in place by engaging 3 Cam Locks
(1) (Refer to page 3 on Cam Lock system operation supplement).
8. Repeat this procedure to attach the Right Side Frame (C) at the opposite end.
3
D
E
B
C
Cam Lock
(6 used in this step)
①
Wood Dowel
(4 used in this step)
③

10
Assembly Instructions
9. Glue six Wood Dowels (3) into the inner holes on the top edge of the Side Frames (B and C) and the
Partition Panel (E).
10. Ask for assistance to position the Top Panel (A) onto the inserted Wood Dowels (3) on the assembled
unit making sure the back edges are even with each other. Attach the Top Panel (A) in place by
engaging six Cam Locks (1).
Wood Dowel
(6 used in this step)
③
Cam Lock
(6 used in this step)
①
D
E
B
C
A
A
1
3
B/C/E

11
Assembly Instructions
11. Tightly screw the Center Support (F) into the threaded hole on the Bottom Panel (D) and set the
adjustable floor leveler to the correct height.
D
B
C
F

12
Assembly Instructions
12. Now, go back and securely tighten all the Cam Locks and Wood Screws. Make sure that all the parts
are tight and there are no gaps between the pieces. This will help keep the unit square.
13. Ask for help to flip the assemled unit around at its front edge.
14. Unfold the Back Panel (J) and lay it onto the back of the assembled unit. Make sure that the mounting
holes for the Cable Wheels (K) on the Back Panel (J) align with the threaded inserts on the back of
Partition Panel (E) properly and the overlaps on the panels are even all the way around. Secure the Back
Panle (J) in place by screwing the 5/8” Washer Head Screws (7) into the pilot holes on the Back Panel.
NOTE: We recommend attaching the back panel with the screws at the top edge first.
J
7
J
J
D
C
5/8” Washer Head Screw
(32 used in this step)
⑦

13
Assembly Instructions
15. Stand the assembled unit upright.
16. Attach 2 Cable Wheels (K) to the center of the Back Panel (J) using two 3/4” Bolts (4) per wheel. You
can use the Cable Wheels to organize your cables and cords.
3/4” Bolt
(4 used in this step)
④
A
J
K
K
4
K

14
Assembly Instructions
17. Attach one Knob (11) to the front side of each Door (H and I) with the provided Knob Bolt (12).
18. Extend the 2 Hinge Arms that are pre-attached on the Right Door (I) and attach them to the Hinge Bases
on the Right Side Frame (C). Loosen the bolt on the back of Hinge Base for an easy fit. Align and insert
the “U” slot on Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door
hinges engage and function properly. Tighten the bolt on the Hinge Base to lock the hinges in place.
19. Repeat the same procedure to attach the Left Door (H) to Left Side Frame (B).
20. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the
screws for a good fit.
Knob
(2 used in this step)
2
1
H/I
B/C
1
2
H/I
I
B/C
H/I
A
B
C
H
11
12
Knob Bolt
(2 used in this step)
⑫

15
Assembly Instructions
21. With the doors open, insert eight Shelf Supports (8) into the desired holes in the sides of each
compartment behind the glass door. Make sure you place the four Shelf Supports in the same level so
the shelf is not tilted. Tilt and rest the Adjustable Shelves (G) onto the Shelf Supports (8) with the
finished edge facing the front of the unit.
22. Plug the Cam Lock Covers (9) onto the visible Cams Locks to conceal the Cams.
Cam Lock Cover
(18 used in this step)
⑨
Shelf Support
(16 used in this step)
⑧
G
G
8
G
8
G
G
9
A

16
Assembly Instructions
NOTE: To prevent your TV from tipping, you must install the Strip Stopper if you place your flat panel
television directly on the console. Otherwise, skip to step 24.
23. Remove the paper backing from the Stop Rail (L), then properly align the Stop Rail with the top edge of
the stopper template on Top Panel (A). Press down on the Stop Rail to help adhesion.
24. Carefully remove the Stopper template from the Top Panel (A).
A
L
L
L

17
Assembly Instructions
Tools required (not provided): Phillips screwdriver, stud finder, power drill and 1/8” drill bit.
25. Ask for assistance to position the assembled unit at the desired location against a wall.
26. In case of uneven floors, the Floor Levelers are provided at the bottom of front legs for the necessary
adjustment. To adjust the unit, simply tilt the unit back and then adjust the floor levelers by hand to
correct tilting and/or level the doors.
27. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to
attach the tip-over restraints to the unit and the wall, as shown in the illustration.
NOTE: The tipping restraint hardware included is for wooden stud wall construction. It must be attached to a
wall stud. Depending upon your wall construction, different anchor hardware maybe required. Please contact
your local hardware store for assistance. Young children can be seriously injured by tipping furniture. You must
install the Tipping Restraint Hardware with the unit to prevent the unit from tipping, causing any accidents or
damage. The tipping restraints are intended only as a deterrent, they are not a substitute for proper adult
supervision. The tipping restraints are not earthquake restraints. If you wish to add the extra security of
earthquake restraints, they must be purchased and installed separately.
Children have died from furniture tip-over.
To reduce the risk of furniture tip-over:
 ALWAYS install tip-over restraint provided.
 NEVER exceed the maximum size and weight of the TV
shown in the instructions.
 NEVER allow children to stand, climb or hang on drawers,
doors, or shelves.
 NEVER open more than one drawer at a time.
 Place heaviest items in the lowest drawers.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
WARNING
B
C
A

18
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage your furniture’s finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 Stains or marks from crayons or ink markers will be difficult to remove.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to minimize the small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace
it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your
highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
Whalen Furniture Manufacturing
1578 Air Wing Road, San Diego, CA 92154, USA
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2019-10-23 Rev. 0001-C
Consola para TV Oxford Square
Serie # BH15-084-899-07 / BH46-084-899-03
# BH46-084-899-04 / BH46-084-899-05
# BHW-10035 / BHW-10036
ENSAMBLE REQUERIDO POR ADULTO
Si tiene alguna pregunta acerca del ensamble o si le hace falta alguna parte, no devuelva este
producto a la tienda. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., Lunes-Viernes
Visite nuestra página de internet 24 horas al dia, 7 días a la semana para asistencia en el producto
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: / /

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Consola para TV Oxford Square
MODELO #: BH15-084-899-07/BH46-084-899-03/BH46-084-899-04/BH46-084-899-05 / BHW-10035/ BHW-10036
HECHO EN VIETNAM
Como ajustar las Bisagras Europeas de las puertas
El embarque de productos puede causar que las puertas queden fuera de nivel. Si encuentra que
las puertas requieren algo de nivelación, gire el tornillo ilustrado adecuado.
1. PARA AJUSTAR HACIA ENFRENTE O HACIA EL
ATRAS.
2. PARA LA DERECHA O IZQUIERDA.
3. PARA AJUSTAR HACIA ARRIBA O HACIA ABAJO.
P ES OS M Á X IM O S R EC OM EN
D A D O S
CARGA MÁXIMA 50 lb. (22.7 kg)
PARA LA MAYORÍA DE TELEVISIONES
DE 55” PANTALLA PLANA
CARGA MÁXIMA 135 lb. (61.2 kg)
PONER LA TV DETRÁS DEL TOPE
ESTA UNIDAD NO DEBE UTILIZARSE CON TELEVISIONES CRT O DE TUBO.
UTILIZARSE ÚNICAMENTE CON TELEVISIONES DE PANTALLA PLANA Y EQUIPO DE
AUDIO/VIDEO QUE TENGAN LA MEDIDA/PESO RECOMENDADO. NUNCA UTILIZAR CON
TELEVISIONES MÁS GRANDES/PESADAS DE LAS RECOMENDADAS. PARA EVITAR
INESTABILIDAD COLOQUE EN EL CENTRO DE LA UNIDAD; LA BASE DE LA TELEVISIÓN
DEBE DE REPOSAR SOBRE LA SUPERFICIE DE SOPORTE DE LA UNIDAD SIN REBASAR LAS
ORILLAS. LAS TELEVISIONES DE PANTALLA PLANA COLOCADAS INAPROPIADAMENTE, O
LAS TELEVISIONES DE PANTALLA PLANA INCLUYENDO EQUIPO QUE SOBREPASA LAS
MEDIDAS Y PESOS RECOMENDADOS PUEDEN CAERSE Y/O ROMPER LA UNIDAD, CAUSANDO
POSIBLES DAÑOS O LESIONES. PARA USO DE TELEVISIONES DE HASTA 135 LBS (61.2 KG) O
MENOS. USO CON TELEVISIONES DE MAYOR PESO PUEDE RESULTAR EN INESTABILIDAD
CAUSANDO QUE LA UNIDAD CAIGA EN ALGUNOS CASOS PROVOCAR DAÑOS O MUERTE.