Beurer IPL PureSkin Pro 5500 User manual

IPL PureSkin Pro 5500
EN IPL PureSkin Pro long-lasting hairreduction
Instruction manual

READ THIS MANUAL COMPLETELY AND CAREFULLY BEFORE USING THIS PRODUCT
Keep this manual in a safe location for future reference

3
1. IMPORTANT SAFETY NOTES
The following signs appear in different pages in this manual.
READ THIS ENTIRE MANUAL, THE SAFETY SECTION
AND ALL INSTRUCTIONS AND WARNINGS COMPLETELY
AND CAREFULLY BEFORE USING THIS PRODUCT.
FOLLOW ALL SAFETY INSTRUCTIONS AND WARNINGS.
ENGLISH
WARNING WARNING indicates a hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION CAUTION indicates a hazardous situa-
tion which, if not avoided, may result
in minor or moderate injury.
NOTICE NOTICE addresses practices not
related to personal injury, such as
product and/or property damage.
Contents
1. IMPORTANT SAFETY NOTES..................................... 3
2. Important information................................................. 8
3. Introduction.................................................................. 9
4. Parts and Controls .................................................... 11
5. Starting the application ............................................ 12
6. Who Can Use The Device? ....................................... 12
7. Who Should Not Use The Device............................. 13
8. Possible Side Effects ................................................ 14
9. Use of the IPL Pure Skin Pro .................................... 15
10. Care and Maintenance.............................................. 20
11. Troubleshooting......................................................... 20
12. Technical Specifications........................................... 24
13. Storage ....................................................................... 24
14. Warranty/service ....................................................... 25

4
Intended Use
The IPL PureSkin Pro device is an over the counter device
intended for the removal of unwanted body and/ or facial
hair in adults. The IPL PureSkin Pro device is also intended
for permanent reduction in unwanted hair. Permanent hair
reduction is defined as a long-term, stable reduction in the
number of hairs regrowing when measured at 6, 9, and 12
months after the completion of treatment regimen. The ideal
body areas on which to use the IPL PureSkin Pro are the
legs, armpits, bikini zone, chest and stomach. The device is
not intended for removing hair on the anus, genitals, nipples
or near the eyes. Only use it in accordance with the instruc-
tions for use. The device is intended for personal use only.
The device is intended for home use only.
CONTRAINDICATIONS
To prevent the possibility of serious personal injury,
do not use this device in the following instances,
since the safety of this device in these cases has not
been fully established.
• If you are under the age of 18.
• If you are pregnant, nursing or might be pregnant.
• If you have skin cancer, on areas at risk of malignancy, or
if you have received radiation therapy or chemotherapy
within the past three months.
• If you have epilepsy.
• On damaged or broken skin or if you have a history of
herpes or psoriasis outbreaks in the treatment area.
• If you suffer from keloid scar formation (growth of
extrascar tissue where the skin has healed after an injury).
• If you have been taking tetracycline antibiotics and
medication with the following active ingredients within
the last two weeks: Retinoid acid, Retin-A, or drugs
containing Vitamin A such as Accutane.
• If you are photosensitive or have other diseases related
to light sensitivity.
• If you suffer from severe or decompensated metabolic
conditions such as diabetes since it may delay healing
and infection in the case of an adverse effect.
• If you have had a skin peel or other skin resurfacing
procedure within the last eight weeks.
• Men must not use the device.
Note
If you have undergone any aesthetic procedures or
have any uncertainty regarding potential side effects,
consult your physician before use.

5
WARNING
To reduce the risk of fire, electric shock, or serious
personal injury:
Before using the device, read the safety notes carefully
and follow the instructions exactly whenever using the
device. Non-observance of the following instructions
can result in injury or material damage. Store the
instructions for use for future reference and make
them accessible to other users.
• Do not use the device when pregnant or breastfeeding.
• Do not allow children to play with the device.
• If you discover extreme reddening, blistering or burns on
the skin, stop using the device immediately!
• Never look directly into the light emitted from the IPL
lamp.
• Never attempt to release a light pulse into the air!
• On the basis of the “Hair and skin color chart” on the
back page of these instructions for use, determine which
light intensities are best suited to the color of your skin
and your body hair and whether this method is suitable
for you to use at all (if not, this is marked by an ’x’ in
the chart).
• Do not use the device on naturally dark skin.
• Do not use the device on tanned skin or after sun
exposure. Avoid exposure to the sun for four weeks
before using this device.
• Do not attempt to open or repair the device. If the
device is opened, you could come into contact with
dangerous electrical components or with pulsed light
energy, which could result in serious injury and/or
permanent damage to the eyes.
• Do not use the device with a contact gel – this may
damage the device.
• Keep the device and adapter away from water! The IPL
PureSkin Pro is an electrical device. Do not place it in
water or allow it to fall into water or any other liquid.
• Do not use the device when taking a bath.
• Do not use the device when it is damp or wet.
• Do not reach for the device if it has fallen into water.
• Immediately unplug the mains adapter if it has fallen
into water.
• Never touch the power adapter or the device with wet
hands.
• Do not use the device under any circumstances if you
suffer from one of the following ailments:
- If you suffer from skin cancer or have done in the past,
or if you have had potential malignancies on the skin
areas to be treated.

6
- If you suffer from epilepsy with flash sensitivity.
- If you suffer from collagen disorders, including the
formation of keloids or poor tissue repair.
- If you suffer from herpes or psoriasis in the treatment
area, unless you have consulted a doctor and
received preventative treatment.
- If you are photosensitive or suffer from another form
of light sensitivity, such as porphyria, polymorphic
photodermatosis, solar urticaria, lupus, etc.
- If you suffer from a metabolic disorder, such as
diabetes.
- If you suffer from a blood clotting disorder.
• Do not use the device under any circumstances:
- If you are taking medication that makes the skin
more sensitive to light, including non-steroidal anti-
inflammatory drugs (for example, aspirin, ibuprofen,
paracetamol), tetracyclines, phenothiazines, thiazide
diuretics, sulphonylurea, sulfonamide, DTIC,
fluorouracil, vinblastine, griseofulvin, alpha hydroxy
acids (AHAs), beta hydroxy acids (BHAs), Retin-A®,
Accutane® and/or topical retinoids.
- If you are undergoing or recently underwent treatment
with azelaic acid.
- If you have been on a course of steroids in the past
three months.
- If you have had a skin exfoliation treatment or other
skin smoothing procedure in the last six to eight
weeks.
- If you have undergone radiation or chemotherapy in
the past three months.
• Do not use the device under any circumstances in the
following areas:
- On mucous membranes in the nose or throat area.
- On or next to an active implant, such as a pace maker
or a device for incontinence, insulin pump, etc.
- On the face above the cheekbones, around the eyes,
eyebrows or eyelashes, as this could result in severe
damage to the eyes.
- On nipples, areolae, inner labia, vagina, anus, nose
and ears.
- Men must never use the device on the scrotum or face.
- On piercings or other metal objects, such as ear rings
or jewelry.
- On tattoos or permanent make-up in the area to be
treated.
- On dark brown or black patches, such as large
freckles, birthmarks, moles, blisters or warts.
- On eczema, psoriasis, lesions, open wounds or acute
infections. Wait until the affected area has healed
before using the device.

7
- On damaged or cracked skin or in areas at risk of
malignancy.
- On an area of your body where you may like to have
hair in the future.
CAUTION
To reduce the risk of personal injury or product/
property damage:
• Use the IPL PureSkin Pro only according to the
instructions for use.
• Hair removal by lasers or intense pulse light sources
can cause increased hair growth in some individuals.
Based upon currently available data, the highest risk
group for this response is females of Mediterranean,
Middle Eastern, and South Asian heritage treated on
the face and neck.
• This appliance is not intended for use by persons with
reduced physical, sensory or mental capabilities.
• Do not use the device if:
- The device is not working properly, appears damaged
or broken (UV and IR emitted from this device)
- The cord or plug are damaged
- You see or smell smoke
- The outer shell is damaged or loose
- Lamp or Treatment Window is damaged/missing
- Optical skin tone sensor is cracked, or broken
- Becomes damp or wet.
• Avoid more than 15 minutes of sun exposure for at least
2 weeks post treatment. If during these two weeks your
treated skin area is exposed to sunlight, make sure to
apply SPF 30 or higher sunscreens.
• Do not treat the same area of skin more than once per
treatment as it may cause skin irritation.
• This device is intended for one individual’s use only. To
help prevent transmitting diseases between users, do
not let others use the IPL PureSkin Pro.
• Do not attempt to open or repair your device. Attempting
to open the device may damage it and invalidates your
warranty.
• The device should never be left unattended when it is
plugged into a socket.
• Do not operate the device if the device itself, a cable
or a plug is damaged and keep the mains cable away
from hot surfaces.
• Always unplug the device from the mains immediately
after use.
• Do not use the device with attachments or accessories
that are not recommended by Beurer.
• During use, do not expose the device to temperatures
below 10 °C or above 35 °C.
• Do not use the device if you see or smell smoke during
use.

8
• Do not use the device if the fan opening on the device
is cracked, is becoming detached or is missing entirely.
• Do not use the device if the skin color sensor on the
device or the light area is cracked or broken.
• Do not direct the light pulse at any other surfaces other
than the skin. Otherwise, this may result in serious
damage to the light emission window or the skin color
sensor. Damage may also be caused to the flashed
surface. Only activate the light pulse once the device is
in contact with the skin.
• After use, store the device in its original box.
• Do not expose the device to several hours of direct
sunlight or UV light in order to prevent damage.
Sunbathing before treatment
1. After sunbathing, wait at least 4 weeks before using
the device.
2. Before treatment, check the skin for signs of sunburn.
If you have sunburn that has not healed, wait until it
has completely healed to use the device.
3. Carry out a skin sensitivity test on the tanned skin (see
section 5.1) to determine which energy intensity is right
for you.
Sunbathing after treatment
1. Wait 2 weeks before sunbathing after treatment. If you
must be exposed to sun, use sunscreen.
2. For the first two weeks after the treatment, the treated
skin must be covered with clothing or sunblock (at
least SPF 30) when you are out in the sun.
Tanning with artificial light
The instructions for “Sunbathing before treatment” and
“Sunbathing after treatment” also apply to tanning using
an artificial light and tanning lotion. Do not use the device
24 hours before or after using a sauna/swimming pool, as
the chlorine may lead to skin irritation.
2. Important information
Signs and symbols
The following symbols are used in these instructions for
use, on the packaging and on the type plate for the device
and accessories:
Warning

9
Caution
Note
Note on important information
Follow instructions for use
Type BF applied part
Device in protection class 2
Keep away from rain
Device protected against foreign objects ≥
12.5 mm and against falling drops of water
14°F
(-10°C)
158°F
(70°C) 90%
0%
Storage
Permissible storage temperature and
humidity
Operating
50°F
(10°C)
104°F
(40°C) 70%
30%
Permissible operating temperature and
humidity
Keep away from eyes
Do not use the IPL PureSkin Pro device on
tanned skin or after sun exposure
Use device only with its original power supply.
For your safety, never use DC adapters which are not
approved by the manufacturer.
3. Introduction
What is the IPL PureSkin Pro?
The PureSkin Pro is a light-based device forlasting hair
removal for private use. The hair removal processbased
on light is a well-known and proven method. In 15 years of
clinical applications around the world, it has proven to be a
safe and effreduction.
Before using the
IPL PureSkin Pro
During a pulse from the
IPL PureSkin Pro
After using the
IPL PureSkin Pro
How does the light remove the hair?
Light-based hair removal is founded on the principle of
selective photothermolysis, whichses optical energy to
deactivate hair growth. To achieve such a thermal effect,

10
the hair root must selectively absorb the light energy and
convert it into heat.
This selectivity is achieved when the optical energy that is
released into the tissue is mainly absorbed by the melanin
pigment in the hair. The high-energy light is converted into
thermal energy (heat), which ultimately deactivates hair
growth. Therefore, the more melanin present in the hair (i.e.
the darker the hair), the more light can be absorbed and
the more effectively the light can work for the hair removal.
What eect does the hair growth cycle have on light-
based hair removal?
Every hair on our body goes through the three phases of the
hair growth cycle: anagen, catagen and telogen. Only hairs
that are in the anagen phase, or growth phase, respond to
treatment with IPL. Although the duration of a complete hair
growth cycle differs from person to person and depends on
the area of the body the hair is growing on, the cycle generally
lasts 18 to 24 months.
Please note that at least one complete hair growth cycle is
required in order to achieve permanent hair removal using
the Beurer IPL PureSkin Pro.
Anagen –
growth phase
Catagen –
transitional phase Telogen –
resting phase
18 – 24
months
Anagen
Telogen Catagen
Long-term hair reduction
Skin types are depicted on the Fitzpatrick scale below. Darker
skin contains more melanin, which competes with melanin
in the targeted hair for energy absorption. When more light
energy is absorbed into the skin, there is a greater risk of
adverse effects and epidermis damage. This device is only
recommended for use on skin types I through IV.

11
III III IV V
X
VI
X
WARNING
Read this user guide completely before starting
treatment with the device.
4. Parts and Controls
1
8
7
2
3
6
5
4
1Treatment window/light area
2Skin Color Sensor/Contact Sensor
3Intensity Level Display
4Power Button
5Indicator Lamp
6Pulse Button
7AC Power Adapter
8AC Adapter Socket
The dierent indicator lights are as followed:
Indicator Mode Description
No light OFF Device not working
(not connected to the
power supply)
Blinking green
light Standby Device is in standby mode (when first
powering on or
when no buttons are
pressed for 3 minutes)
Green energy
level LEDs
(1 -3)
Energy
level 1-3 The three energy levels are indicated by
three green LEDs.

12
Steady green
light ON Pulse is ready
Short orange
light flash Activation (pulse)
blocked
The device does not
deliver a pulse due to
lack of full skin con-
tact.
Short red light
flash Activation (pulse)
blocked
The device does not
deliver a pulse due to
non-allowed skin tone.
Blinking or-
ange light Close to end of life Pulse light is near- ing the end of its ser-
vice life
“Steady” red
light End of life/ blocked Device has malfunctioned or
Pulse Light has
reached the end of its
service life
5. Starting the application
1. Insert the device plug into the device and insert the mains
plug into the main socket. The indicator lamp begins to
flash green (stand-by).
2. Press the Power Button. Pressing the button will turn
the device on at energy level 1. Each press will change
the energy level in a cyclic manner, from the lower level
to the higher, and then back to the lowest, for a total of
3 different energy levels. The selected energy level is
indicated in the ‘Intensity level display’.
3. If you wish to carry out an application at a higher intensity
level, increase the intensity by repeatedly pressing the
Power Button until you have reached the desired intensity.
4. Position the light area on the skin and press the trigger
button in order to release a light pulse. Ensure that the
light area and skin contact sensor come into full contact
with the skin. A light pulse can only be released once the
skin contact sensoris in full contact with the skin. You will
see a bright flash, hear a cracking noise and may feel
a slight burning sensation and/or warmth. The device
fan switches on after the first flash. Within 1-3 seconds
(depending ont he intensity level), the device is ready for
the next pulse and the indicator lamp on the device is
continuously illuminated green.
6. Who Can Use The Device?
The device is intended for women who desire to remove
unwanted hair.
This device can be used on skin tone types 1 to 4 as
pictured in the Fitzpatrick skin chart below and on the back
cover. Do not use on dark skin such as types 5 and 6.

13
IPL PureSkin Pro works best on dark hair, which contains
more melanin. Lighter hair will respond, but typically will
require more treatment sessions. White, gray or blond
hair shows a more limited response, but some users have
noted hair reduction after multiple treatment sessions.
III III IV V
X
VI
X
Benefits:
This device features a built-in skin color sensor that
continually evaluates your skin tone and allows treatment
only on suitable areas. This safety feature also disables
treatment if the skin in the treatment area is too dark or
tanned, even if your general skin type is lighter. As an extra
precaution, this device only emits a light pulse when it is in
contact with your skin.
Notes:
Response to the device hair reduction differs between
individuals depending on biological factors and how
treatment instructions are followed. Hair removal by lasers
or intense pulse light sources can cause increased hair
growth in some individuals. Based upon currently available
data, the highest risk groups for this response are females
of Mediterranean, Middle Eastern, and South Asian heritage
treated on the face and neck.
7. Who Should Not Use The Device
WARNING:
To prevent the possibility of serious personal injury,
do not use this device in the following instances,
since the safety of this device in these cases has not
been fully established.
• If you are under the age of 18.
• If you are pregnant, nursing or might be pregnant.
• If you have skin cancer, on areas at risk of malignancy, or
if you have received radiation therapy or chemotherapy
within the past three months.
• If you have epilepsy.
• On damaged or broken skin or if you have a history of
herpes or psoriasis outbreaks in the treatment area.
• If you suffer from keloid scar formation (growth of
extrascar tissue where the skin has healed after an injury).
• If you have been taking tetracycline antibiotics and
medication with the following active ingredients within

14
the last two weeks: Retinoid acid, Retin-A, or drugs
containing Vitamin A such as Accutane.
• If you are photosensitive or have other diseases related
to light sensitivity.
• If you suffer from severe or decompensated metabolic
conditions such as diabetes since it may delay healing
and infection in the case of an adverse effect.
• If you have had a skin peel or other skin resurfacing
procedure within the last eight weeks.
• Men must not use the device.
Note
If you have undergone any aesthetic procedures or
have any uncertainty regarding potential side effects,
consult your physician before use.
8. Possible Side Effects
If used according to these instructions, side effects from
this device are rare. Any aesthetic procedure can cause
some degree of side effects, however. It is important to
understand the risks and complications that could occur
with a pulsed light hair removal system.
Please consult your physician if necessary.
Degree of Side Effects Side Effects
Minor Skin Irritation
Skin Redness
Skin Sensitivity
Rare Skin Burns
Scarring
Pigment Changes
Excessive Redness and
Swelling
Extremely Rare Infection
Bruising
• S kin Redness - Redness on the treated area may appear
after treatment or within 24 hours. Consult your physician
in case the redness does not disappear after 2 to 3 days.
• S kin Sensitivity - You may feel that skin in the treated
area is more sensitive or you may encounter dryness or
flaking of the skin.
• S kin Burns - Rarely, burns on the treated area can occur
following the use of the hair removal reduction system.
The burns can require a few weeks to heal and, extremely
rarely, may leave a visible scar.

15
• S carring - In rare cases, long-lasting scarring may occur.
Usually when scarring occurs it is in the form of a flat and
white lesion on the skin (hypotrophic). However, it can be
large and red (hypertrophic) or large and extend beyond
the margins of the injury itself (keloid). Subsequent
aesthetic treatments may be required to improve the
appearance of the scar.
• P igment Changes - Use of the device may cause
temporary skin hyperpigmentation (increased pigment
or brown discoloration) or hypopigmentation (whitening)
to the surrounding skin. The risk is higher for people
with darker skin tones. Usually discoloration or changes
to skin pigment are temporary and long-lasting
hyperpigmentation or hypopigmentation rarely occur.
• Excessive Redness and Swelling - Very rarely, the treated
area skin may become red and swollen. This side effect is
most common in sensitive areas of the body. Redness and
swelling should decrease after 2 to 7 days and you should
treat the area by apply ing ice. Avoid exposure to sun.
• I nfection - In rare cases, infection of the skin could occur
after a burn caused by the treatment.
• B ruising - Blue-purple bruising is exceedingly rare and
could last 5 to 10 days. As bruising fades, there could
be a long-lasting rusty brown discoloration of the skin
(hyperpigmentation).
9. Use of the IPL Pure Skin Pro
1. Remove all components from the box (handheld device
and power supply).
2. Before beginning the treatment, make sure the device is
clean, dry, and intact.
3. Plug the power supply end into an electrical outlet and
the round cord end into the AC Adapter Socket.
Preparing Skin for Treatment
1. Before treatment, make sure your skin is shaved, clean,
and dry (free of any residue such as powders, creams,
makeup, antiperspirants, or deodorants).
2. Between treatments, you can shave but do not wax or
pluck treated hair.
3. Never use flammable liquids such as alcohol (including
perfumes, sanitizers, or other applications containing
alcohol) or acetone to clean the skin for at least one hour
before treatment.
4. Ensure device is clean and then perform a prelimin-
ary test on a small patch of skin in the intended treat-
ment area 48 hours prior to first full use. This test will
help determine the proper energy level setting for your
skin type (see the “Preliminary Test” section below).

16
Skin Sensitivity Test
A preliminary test will determine your skin‘s reaction to the
IPL PureSkin Pro treatment and help you set the optimal
energy level for each treatment area. Perform a preliminary
test on each area you intend to treat 48 hours prior to the
full treatment.
CAUTION:
Do not treat full areas with energy levels that you have
not tested before! Do not treat the tested area for at
least 48 hours after the skin sesitivity test is completed.
1. Select an area of skin to test and place the treatment
window in full contact with the skin. Press the Power
Switch once to select Energy Level 1 and then press and
hold the Pulse Button once to emit a single pulse.
2. If you feel comfortable with the energy level, press the
Power Switch again to increase to Energy Level 2, move
the treatment window of the device to another test area
of skin and press the Pulse Button again.
3. If you still feel comfortable, you increase the Energy Level
to 3.
4. Stop the test if you do not feel comfortable, as increasing
the energy level increases the risk of adverse effects.
5. If you see adverse effects such as severe redness or
blistering, stop the test immediately.
6. Wait 48 hours and examine the tested area. If the skin in
the test area seems normal (no response or mild redness
observed), you can proceed with a full treatment in the
highest comfortable energy level. If you see excess
redness, swelling, or blistering even in the low-energy
level settings, do not treat that area.
Treating the Skin
CAUTION:
Conduct a preliminary test before performing a full
treatment. See the “Preliminary Test” section above.
1. Plug the power cord into the device; the green power
LED will flash indicating the device is in standby mode.
Press the Power Switch to turn on the device; one
green Level LED will illuminate indicating the device
is set to Energy Level 1. To increase the Energy Level,
press the Power Switch repeatedly to select Energy
Level 2 or 3.

17
2. Position the treatment window onto the desired area of
skin, making sure it makes full contact. If the treatment
window is not properly positioned, the Power LED will
briefly change to orange. If your skin tone is too dark/
tanned, the Power LED will briefly change to red. In
either case, the device will not operate.
3. Press the Pulse Button for a single pulse or press and
hold for continuous operation. After the first pulse, the
internal fan in the device may switch on.
4. When pressing the Pulse Button you will see a bright
flash, hear a popping noise, and may feel a mild
heating sensation.
5. Keep the Pulse Button pressed and move the device
to a different area after each pulse while keeping
it in contact with the skin. Continue until the entire
treatment area has been covered.
6. After treatment, shut the device off by pressing and
holding the Power Switch for three seconds; the orange
LED will illuminate while the device is in shutdown
mode, followed by blinking green which indicates the
device is in standby mode. Unplug the device after
each treatment session.
CAUTION:
• Do not overlap pulses in the same spot. Repeated pulses
on the same spot may cause burns.
• Do not treat the same area of skin more than once per
treatment as it may cause skin irritation.
Application methods
Treat the skin in rows, which enables you to keep track of
the areas of skin that have already been treated and helps
you to avoid overlapping the same area. The light emitter
is designed to leave a temporary impression on the treated
area of skin that you can use for precise placement of the
next pulse.
Application method 1 “Auto Flash” mode:
Hold down the Pulse Button with the skin contact sensor
in full contact with the skin. After the third light pulse, the
device will switch to “Auto Flash” mode and will emit light
pulses at regular intervals with no need to hold the Pulse
Button. Auto Flash mode is suitable for treating large areas
such as the legs.
Application method 2 “Single Flash” mode:
Press the Pulse Button and release immediately after each
pulse. Reposition the device over the next area to be treated

18
and press the Pulse Button again. Ensure that the light area
and skin contact sensor come into full contact with the
skin. This mode guarantees precise treatment, such as for
knees and ankles.
NOTE: Allow the device to cool for a few minutes if it feels
too hot for you. Continue your treatment after a short cooling
period.
Facial Treatment Method:
WARNING:
If you have undergone any other aesthetic procedures
• Men must not use this device on the face.
• Do not use energy level 3 on the face. Do not use the
device on the face above the cheekbones or on the eyes,
eyebrows or eyelashes, as this could result in severe
damage to the eyes. Do not use the device on mucous
membranes in the nose or throat area.
The skin on your face is very sensitive and requires special
care. Observe all warning and safety notes in these instruc-
tions for use to prevent adverse consequences. We recom-
mend first performing a treatment on your body and get to
know the device before performing facial treatment. The de-
vice can be used to treat all areas of the face below the cheek-
bones, such as the upper lip, cheeks, jaw, chin, and neck.
1. You must carry out a skin sensitivity test 48 hours befo-
re treatment. Perform the skin sensitivity test on an area
without hair, such as below the ear or on the side of the
neck, to determine the suitable energy level. Do not treat
the tested facial area for at least one week after perfor-
ming the skin sensitivity test.
2. Mark the treated area with a white eyeliner pencil. Use
the marking as an orientation line for treatment areas.
This way you can prevent overlapping treatment areas or
treating other areas of the face by mistake.
3. Use a mirror to position the device correctly on the treat
ment area.
Treating the upper lip
Position the light emitter as shown in the gray
areas in the figure at right. Trigger a pulse
in every marked zone. Avoid applying the
treatment to the nostrils and lips, as these
areas are more sensitive.
You can “fold in” your lips or press them together to make
the treatment area flatter or apply a thick layer of white
eyeliner to the lips and around the edge of the lips. The
white line ensures that the energy of the flash is reflected
and does not reach your lips, should you accidentally apply
a pulse to your lip.

19
Treating the cheeks and jaw
Position the light area of the device as shown in the figure.
At each point, trigger a pulse and move from one side of
the cheek or jaw to the other.
Treating the neck and chin
Position the light area of the device as shown in the figure.
At each point, trigger a pulse and move from one side of
the neck or chin to the other.
Facial Treatment Method:
• Apply a soothing lotion such as aloe vera.
• Do not use exfoliators, whitening lotions or similar
products for at least 24 hours, as this could irritate the
treated skin.
• For at least 48 hours after the treatment, avoid more than
15 minutes of direct exposure to the sun. If the treated skin
is exposed to sunlight during this period, sun protection
with SPF 30 or higher must be applied.
• Do not remove hair on the treated areas using wax or
tweezers.
Remember that it may take a complete hair growth cycle
for hair removal to be complete.
Treatment Frequency
Body Hair Color Light Brown
to Brown
Brown to Black
Fitzpatrick Skin
Level
1-4 (inclusive) 1-4 (inclusive)
Energy Levels 1-3 1-3
Treatment Area Legs Legs
Arms Arms
Underarms Underarms
Bikini line Bikini line
Average Number
of Treatments
10-12 8-10
Treatment
Interval
The first four treatments will be ap-
proximately two weeks apart, fol-
lowed by four-week time intervals.
After Treatment
1. When you have completed each treatment session, press
and hold the Power Button for three seconds to enter

20
Standby Mode, which is indicated by the green indicator
light flashing.
2. Unplug the power adapter from the electrical outlet.
3. Clean the device, in particular the light area as instructed
in the “Care and Maintenance” section.
4. Store the device in its original box and keep it away from
water.
5. After treatment, do not use any antiperspirants/
deodorants as these may cause skin irritation. Do not use
peeling and bleaching creams or products for at least 24
hours. Avoid direct sun exposure for at least two weeks.
If recently-treated skin is exposed to sunlight in this time
period, make sure to apply SPF 30 or higher sunscreen.
Do not wax or pluck hairs from treated areas.
What to expect when using the
IPL PureSkin Pro
During treatment it is normal to experience:
• Aflash of light on each press of the Pulse Button. The
light will not harm the eyes when the device is applied
with full contact to the skin.
• Apopping noise with each pulse.
• A sensation of heat radiating from the treated area after
each pulse.
• S ome mild red or pink coloration during and just after
treatment.
After Treatment:
• A pply a soothing lotion such as aloe.
Remember that hair may take up to two weeks to fall out if
the hair follicle is still active.
10. Care and Maintenance
• Shut off and unplug the device before cleaning.
• Clean the light emitter area and skin contact sensor after
every session by using a slightly damp, lint-free cloth.
• Keep the device dry. Never place, store or use this device
near bathtubs, showers, basins or other containers of
water as this may cause electric shock.
• If you do not plan on using the device for a long period
of time, clean it and store it away.
11. Troubleshooting
• If the device does not turn on:
a. Ensure the power cord is connected properly into
the device and the electrical outlet.