BH FITNESS SPRINT BIKE TWO H918A-1 User manual

H918A-1
SPRINT BIKE TWO

2

3

4
Assembly Drawing

5
Assembly
Step one
Attach the front (16) and rear feet (12) to the frame using the nuts (8), washer (9) and bolts (10).
Step two
Attach the handlebar post (37) inserting into the head tube on the frame. Using knob (4) to
adjusts and tightens the height in proper position. Then attached handlebar slider (21) on the
handlebar post (37), use release lever (64) to adjust and tighten the handlebar in proper position.
Step three
Insert the seat post (41) into the frame’s seat tube. Attach the saddle (1) into seat slider (40),
and then tighten the screw of saddle. Insert the seat slider (40) into the seat post (41) and fix.
Using knob (4) adjusts and tightens the height in proper position.
Step four
Attach the pedals (11) into the crank arms (5)(7), each pedal is marked with the L (left) or R
(right) to denote the side of the spinning bike they are on, Note- the right hand crank is on the
same side as the belt guard (6). Be careful to align the threads correctly to avoid any damage.
A little grease on the threads should help the pedals to screw in easily and correctly, tighten using
a 15mm spanner; both pedals threads should tighten towards the front of the spinning bike.
Adjusting the resistance
To adjust the exercising resistance on the complete spinning bike by the brake knob (31) of brake
system, and then simply loosen (-) or tighten (+).
The flywheel should rotate freely without resistance when you loosen (-) the brake system
totally.
More experienced riders may wish to increase the overall resistance by tighten (+) the brake
system totally.

6
Exploded Drawing

7
Part list
No. Name Unit No. Name Unit
1 Saddle PC 34 Bottle PC
2 Alloy bind clip ( R) & ( L ) PC 35 Bolt & washer for spring plate PC
3 Knob spring PC 36 Belt PC
4 Knob w/washer PC 37 Handlebar post PC
5,7 Crank arm set SET 38 Rubber sleeves PC
6 Outer belt guard PC 39 End plug PC
8 Foot tube nut PC 40 Seat slider PC
9 Foot tube washer PC 41 Seat post PC
10 Foot tube bolt PC 42 Bolt for outer chain guard PC
11 Pedal PR 43 Flywheel SET
12 Rear foot tube (complete) SET 44 Flywheel adjuster bolt PC
13 Foot tube adjuster pad PC 45 Bolt for inner belt guard M6 PC
14 Foot tube end cap PC 45-1 Washer for inner chain guard PC
15 Moving wheel PC 46 Bolt for sensor support PC
15-1 Axle bolt for moving wheel PC 47 Cable clip PC
16 Front foot tube (complete) SET 48 Bolt for cable clip PC
17, Leather pad PC 49 Knob fixed bolt PC
17-1 Screw for leather pad PC 50 Knob plastic washer PC
18 Leather pad holder PC 51 Knob washer PC
19 Screw & nut PC 52 Belt pulley with screw PC
20 Spring plate PC 53 Flywheel security washer PC
21 Handlebar PC 54 Left axle cover PC
22 Crank bolt PC 55 Flywheel axle housing (L) PC
23 BB bearing PC 56 Flywheel security nut (T10.5) PC
24 BB Axle w/plate PC 57 rear fender bracket PC
25 Flywheel nut cap PC 58 fender bracket PC
26 Flywheel axle PC 59 Stainless screw PC
27 Flywheel bearing PC 60 Screw PC
28 Computer PC 61 Stainless washer PC
29 Bottle cage PC 62 Fender PC
30 Screw for bottle cage PC 63 Stainless nut PC
31 Brake system SET 64 Handlebar release lever w/washer PC
32 Bolt for front chain guard PC
33 Front belt guard PC 90 Sensor and cable

8
Instruction Use
1) The model H918A-1 is designed to be used as a “spin “ cycle in fitness studios and health clubs. It has a fixed
wheel driven flywheel and should only be used under professional supervision.
2) Installation – it is important that the H918A-1 is correctly assembled and we recommend that suitably qualified
personnel carry out installation and assembly
.
3) Handlebar and seat adjustment. It is important that the handlebar and seat are set at the correct height for your
body. Ask your instructor for assistance. Adjusting the handlebar height-Undo knob that is located where the
handlebar post fits into the frame. Slide the handlebar post up or down to the required height and retighten the
knob. Make sure it is securely tightened and that there is no lateral or vertical movement of the handlebar. The
handlebar position can also be adjusted forwards or backwards. Undo the Release lever located below the
handlebar slider. Slide the handlebar assembly forwards and backwards until you reach the required position.
Then securely re-tighten the Release lever.
Adjusting the seat height- undo the knob located where the seat post fits into the frame. Adjust the seat to the
required height. Then retighten the knob. Make sure it is tighten enough to prevent the seat from twisting side
to side. The seat position can be adjusted forwards and backwards. Undo the knob located directly side of the
seat slider. Loosen the knob then slide the seat to the required position. Then make sure the knob retighten.
4) Pedals and toe straps- your feet should be securely positioned in the toe clips during the exercise. Put your foot
as far forwards as you can into the toe-clip and then pull the strap tight.
5) The H918A-1 should operate on a level surface with no lateral movement. There is height adjuster pad located
on either side underneath of the foot tube. Turn these pads clockwise or anti-clockwise until the bike is totally
stable on the ground.
6) Emergency brake – Press down brake system (31) for stop.
7) Maintenance – It may be unsafe when loosen bolt on the parts or noise on the flywheel, please contact your
supplier. Like any other mechanical cycling device, the H918A-1 should be regularly maintained. Ask your
supplier for a detailed maintenance program.

9
Maintenance Chart
No DESCRIPTION Daily Weekly Monthly Quarterly Annually
1 Wipe machine down X
2 Spray with WD40 or similar X
3 Visual check X
4 Check security of handle bar post &
seat post X
5 Check security of saddle X
6 Remove handlebar post and clean
tube X
7 Remove seat and clean tube X
8 Check brake pads for wear-align X
9 Check brake adjustment X
10 Check security of all knobs & release
lever X
11 Check toe straps for signs of wear X
12 Check crank bolts and re-tighten X
13 Make sure pedals are screwed in X
14 Check belt tension X
15 Wipe the anti-rust oil on the
flywheel X
16 Check bottom bracket X
17 Check flywheel bearings X
18 Full service-frame inspection X

10
LimitedWarranty
This product carries the following guarantee against manufacturing defects:
* Frame is warranted for 2 years from the date of purchase.
* Components are warranted for 1 year.
* Warranty is only valid for the original purchaser.
* Labor and freight charges are not included.
* Normal wear, neglect, abuse, accidents, improper assembly or maintenance, or the
installation of parts or accessories not compatible with the original intended use
of the bike, as sold, are not covered by the warranty.
* Neither does it cover any corrosion caused by failure to clean the bikes on regular
basis.
* This warranty is limited to the repair or replacement of the defective part at no
cost. The supplier shall in no event be responsible for consequential, special
damages, and any parts failures, breakages or injuries resulting from misuse of
the machine or failure to follow the recommended maintenance procedures.
* Warranty claims must be through an authorized dealer, and replacement parts will
normally be dispatched to you. We recommend you held a small stock of basis
spare parts, as well as a tool kit to cover the regular maintenance routines.
* The Limited Warranty is the only express or implied warranty
applicable to original supplier. Any implied warranties, including warranties of
merchantability and fitness shall be limited in scope and duration in accordance
with this limited warranty.