Big Bike Parts 52-562 User manual

INSTALLATION INSTRUCTIONS
PART NO. 52-562 LED LOWER AIR VENT
10/3/2011
HONDA GL1500 GOLDWING 1988 - 2000
TOOLS NEEDED: PHILLIPS SCREWDRIVER 10MM SOCKET WRENCH
PLEASE READ THROUGH AND UNDERSTAND THESE
INSTRUCTIONS BEFORE BEGINNING.
INSTALLATION
1. PARK THE BIKE ON A LEVEL SURFACE
2. REMOVE THE TWO SCREWS (2A) FASTENING THE
TRIM HOLDER (2B) TO THE BIKE AND REMOVE
THE TRIM HOLDER.
3. REMOVE THE TWO SCREWS HOLDING THE
LOWER VENT (3A) IN PLACE AND PULL THE VENT
FORWARD TO REMOVE FROM THE
MOTORC CLE.
4. REMOVE THE COVER (4A) FROM THE RIGHT
FAIRING POCKET. REMOVE THE FOUR SCREWS
(4B) AND PULL THE FAIRING POCKET (4C) OUT
OF THE FAIRING.
5. USE THE 10MM SOCKET WRENCH TO REMOVE
THE FOUR BOLTS (5B) THAT HOLD THE
HEADLIGHT (5A) IN PLACE. THE LOWER BOLTS
WILL HAVE A THREADED HOLE IN THE HEAD.
WHEN THE BOLTS ARE REMOVED THE
HEADLIGHT CAN BE PULLED OUT OF THE
FAIRING. THE HEADLIGHT DOES NOT HAVE TO
BE DISCONNECTED FROM THE HARNESS IF OU
CAN SAFEL REST IT ON THE BIKE WHERE IT IS
OUT OF THE WA .
2A
Copyright
©
2011 by Big Bike Parts, Inc. No part of
this instruction sheet may be reproduced
without the written permission of Big Bike Parts,
2A
2B
3A
4A
4B
4C
5B
5B
5A

6. WITH THE HEADLIGHT REMOVED FROM THE BIKE
LOCATE THE OPENING (6A) IN THE LEFT REAR OF
THE HEADLIGHT RECESS. FEED THE LED AIR VENT
HARNESS THROUGH THIS HOLE AND BACK TO
THE OPENING WHERE THE RIGHT FAIRING
POCKET FITS.
7. FIND THE GREEN TWO POLE CONNECTORS (7A)
THAT ARE LOCATED IN THE AREA UNDERNEATH
THE RIGHT FAIRING POCKET OPENING. ON
SOME MOTORC CLES THERE WILL ONL BE ONE
CONNECTOR. THE INSTALLATION WILL BE THE
SAME AS FOR BIKES WITH TWO CONNECTORS,
BUT ONL ONE CONNECTOR ON THE LED
LOWER AIR VENT WILL BE USED.
8. DISCONNECT THE FEMALE CONNECTOR (8A)
FROM THE MALE CONNECTOR (8B) B
DEPRESSING THE TAB ON THE FEMALE
CONNECTOR WHILE PULLING THE TWO
CONNECTORS APART.
9. CONNECT THE LED LOWER AIR VENT HARNESS
FEMALE CONNECTOR (9B) TO THE FACTOR
HARNESS MALE CONNECTOR (9A). CONNECT
THE LED LOWER AIR VENT HARNESS MALE
CONNETOR (9C) TO THE FACTOR HARNESS
FEMALE CONNECTOR (9D). MAKE CERTAIN
THAT THE CONNECTORS ARE FULL INSERTED
AND LOCKED IN POSITION.
10. TEST THE LED LOWER AIR VENT B TURNING THE
KE TO THE ACCESSOR POSITION. THE LED AIR
VENT FUNCTIONS AS A RUNNING LIGHT AND
WILL ILLUMINATE WITH THE HEADLIGHT. IF THE
LED LOWER AIR VENT DOES NOT ILLUMINATE
CHECK THE CONNECTIONS AND REPEAT THE
TEST PROCEDURE.
11. INSTALL THE HEADLIGHT. MAKE CERTAIN THAT
THE BOLTS WITH THE THREADED HOLES IN THE
HEAD ARE IN THE LOWER MOUNTING HOLES.
ROUTE THE HARNESS FOR THE LED LOWER AIR
VENT TO THE LOWER LEFT SIDE OF THE
HEADLIGHT
12. INSTALL THE LED LOWER AIR VENT USING THE
TWO SCREWS FROM THE FACTOR LOWER AIR
VENT.
13. INSTALL THE TRIM HOLDER
14. INSTALL THE RIGHT FAIRING POCKET.
RIGHT
TURN
SIGNAL
6A
OPENING IN BACK
OF HEADLIGHT
7A
FACTOR CONNECTOR
(GREEN)
8A
8B
9A
9B
A
9C 9D
TO LED
LOWER
AIR VENT