Big Lots SW-RK939 User manual

TWO SEATER CUSHONED SWING
ASSEMBLY INSTRUCTIONS
ITEM# SW-RK939
SKU# 810502906
DO NOT RETURN THIS PRODUCT TO THE STORE. FOR MISSING PARTS OR QUESTIONS TO THIS PRODUCT PLEASE CALL US AT 1-888-733-8169
OR EMAIL US AT customerservice [e-mail] OR customerservice [e-mail] OR customerservice [e-mail]
IMPORTANT :
Please read all the instructions and warnings before assembling . In order to make the whole product adjust to the best, please install all the screws on the product
before fully tighten, and note to put the washer to the screw before putting the screw into the screw hole.
WARNING :
Use the correct screws as indicated. All screws should be hand tighten until the complete piece is assembled ( This will make the
assembly process much easier ). Once the piece is fully assembled, then go back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product construction .
Keep assembly area at leat 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and use.
The swing is for sitting purpose only, is not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The swing is not a toy. This three seater swing tested for use at weight of 350 lb (158.7kg). Improper use of this product or failure to use
as directed may result in injury. Not intended for commercial use.
CARE & MAINTENANCE
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE IN RAINING DAYS.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushion to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.

PARTS LIST FOR SWING
NO. Part Qty Image NO. Part Qty Image
ALeg Tube 4
66.9"
MPlastic Washer 4
BStanding Support 2
27.2"
NScrew (M6X55MM) Unit 2
CTop Hanging Pole 1
56.5"
OScrew (M6X35MM) Unit- 3PC 8
DArmrest 2PScrew (M6X35MM) Unit - 4PC 4
EShort Hanging Pole 2
31.7"
RScrew (M6X70MM) Unit 2
FLong Hanging Pole 2
33.5"
SS Screw (M6X38MM) Unit 4
G1 Right Seat Back 1TScrew (M6X82MM) Unit 4
G2 Right Seat Back 1UScrew (M6X60MM) Unit 4
HSeat Panel 1VScrew (M6X40MM) Unit 1
ISupport Connecter 2WScrew (M6X25MM) Unit 2
JFabric Cover 1X1 Wrench 1
KAjustable Handle 2X2 Allen Wrench 1
LSpring 2
Warranty
One-year limited warrantly.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer 's responsibility for freight and packing charges to and from the service center.

STEP 1 STEP 2
Secure Top Hanging Pole (C) to 4 Leg Tube (A) with 4 Screw Unit (T) by using
Wrench (X1) and Allen Wrench (X2) . Do not tighten all screws now.
1. Secure 2 Support Connecter (I) to Top Hanging Pole (C) with 2 Screw Unit (SS) by using
Wrench (X1) and Allen Wrench (X2) .
2. Secure 2 Standing Support (B) to 4 Leg Tube (A) with 8 Screw Unit (O) by using Allen
Wrench (X2) .
3. Secure 2 Support Connecter (I) to 4 Leg Tube (A) with 4 Screw Unit (P) by using Wrench
(X1) and Allen Wrench (X2) .
STEP 3
1. Secure Right Seat Back (G1) to the upper 2 holes for Left Seat Back (G2) with 2 Screw Unit (SS) by using Wrench (X1) and Allen Wrench (X2) .
2. Secure Right Seat Back (G1) to the bottom 1 hole for Left Seat Back (G2) with 1 Screw Unit (V) by using Wrench (X1) and Allen Wrench (X2) .
3. Secure 2 Armrest(D) to 2 Long Hanging Pole (F) with 2 Screw Unit (R) by using Wrench (X1) and Allen Wrench (X2) .
4. Secure 2 Armrest(D) to 2 Short Hanging Pole (E) with 2 Screw Unit (N) by using Wrench (X1) and Allen Wrench (X2) .
5. Secure 2 Armrest(D) to Seat Panel (H) with 4 Screw Unit (U) and 4 Plastic Washer (M) by using Wrench (X1) and Allen Wrench (X2) .
6. Secure 2 Armrest(D) to Right Seat Back (G1) and Left Seat Back (G2) with 2 Screw Unit (W) by using Wrench (X1) and Allen Wrench (X2) .
7. Adjust the Short Hanging Pole (E) and Long Hanging Pole (F) close to connect the Spring (L).

STEP 4 STEP 5
Hanging the assembled swing to connect the Top Hanging Pole (C) by Spring (L).
Verify the alignment and adjust, fully tighten all screws.
Secure Fabric Cover (J) to Top Hanging Pole (C) with 2 Ajustable Handle (K) by
hand.
STEP 6
Finished!