Fisher-Price H4791 User manual

Instructions
Model Number: H4791
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires four LR14 ("C") alkaline batteries for operation (not included).
Weight Limit: 9 Kg (20 lbs).
Product features and decorations may vary from picture above.
www.fisher-price.com
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.

2 Base Tubes
Toy Bar
5 Toys
Parts
2 Swing Frames
Seat Pad
#6 x 1.9 cm Screw – 2
Shown Actual Size
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the pad.
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
Seat Frame
2
2
To prevent serious injury or death from falls and being strangled in the
restraint system:
-Always use the restraint system.
-Not recommended for children who sit up by themselves (6 months approxi-
mately, until 9 Kg, 20 lbs).
•Never leave child unattended.
•It is dangerous to use this product on an elevated surface.
WARNING
CAUTION
This package contains small parts in its unassembled state.
Adult assembly is required.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2004 Mattel, Inc. All Rights Reserved. PRINTED IN CHINA
®and ™ designate U.S. trademarks of Mattel, Inc. H4791pr-0726

3
3
Assembly
1
2
Swing Frame Front Leg
Swing Frame Back Leg
•Slide the front and back legs on the swing frame outward
until they “click” into place.
•Repeat this procedure to open the other swing frame.
Base Tube
Press Buttons
on Front Legs
•While pressing the buttons on the end of each front leg,
insert the front legs into the ends of one of the base tubes.
•Push the front legs down into the base tube until the
buttons “click” into place.
IMPORTANT! Before assembly, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
3Base Tube
PULL UP
•While standing on the base tube, pull the front legs up. The
front legs should remain secured to the base tube. If you can
remove the front legs, you have not assembled them correctly
to the base tube. Re-read and repeat assembly step 2.
4
Base Tube
Press Buttons
on Back Legs
•While pressing the buttons on the end of each back leg, insert
the back legs into the ends of the remaining base tube.
•Push the back legs down into the base tube until the buttons
“click” into place.

4
4
•Position the seat frame so that the tubes are upright,
as shown.
Hint: Note the location of the socket inside each seat hub. The ends of the
frame arms will be inserted into these sockets.
•Fit the end of each frame arm into the socket in each seat hub.
Base Tube
5
6
Assembly
•While standing on the base tube, pull the back legs up. The
back legs should remain secured to the base tube. If you can
remove the back legs, you have not assembled them correctly
to the base tube. Re-read and repeat assembly step 4.
PULL UP
Frame Arm
Frame Arm
Seat Frame
Seat Hub
Seat Hubs
Socket
Socket
7
Seat Hub
Seat Hub
•Insert a 1.9 cm screw through the outside of each seat hub
and into each frame arm. Tighten the screws.
#6 x 1.9 cm Screw – 2
8
•Fit the pad upper pocket over the seat back tube.
•From behind the assembly, insert the waist belts through the
slots in the pad.
•Press to fasten the waist belt assembly to the pad.
Seat Back Tube
Pad Upper Pocket
Waist Belts
Waist Belt
Fasteners
Slots

5
5
Assembly Battery Installation
Battery Safety Information
9
10
•Fit the pad lower pocket onto the seat bottom tube, as shown.
•Insert and “snap” the peg on the toybar into the socket on the
swing arm. Pull the toy bar up to be sure it is secure.
Assembly is now complete.
Pad Lower Pocket
Seat Bottom Tube
Toy Bar
Socket
Hint: We recommend using alkaline batteries for longer battery life.
Shown Actual Size
1,5V x 4
LR14 (“C”)
Note: Low battery power may cause product movement to slow
and sound volume to become faint or turn off all together. If this
should happen, please remove and discard all four batteries and
replace with four, new LR14 (“C”) alkaline batteries.
•Locate the battery compartment door on the frame.
•Loosen the screws in the battery compartment door.
•Remove the battery compartment door.
•Insert four "C" (LR14) alkaline batteries.
•Replace the battery compartment door and tighten the screws.
Battery Compartment Door
Batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of batteries in a fire. The
batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type as recom-
mended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the product
before charging.
•If removeable, rechargeable batteries are used, they are only to
be charged under adult supervision.

6
6
Securing Your Child
To prevent serious injury or death from falls and being strangled in the
restraint system:
-Always use the restraint system.
-Not recommended for children who sit up by themselves (6 months approxi-
mately, until 9 Kg, 20 lbs).
•Never leave child unattended.
•It is dangerous to use this product on an elevated surface.
WARNING
Waist Belt
Restraint Pad
Buckle
•Place your child in the seat. Position the restraint pad between
your child’s legs.
•Fasten both waist belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
•Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint should
remain attached.
Free End
TIGHTEN LOOSEN


Anchored End
Anchored End
To tighten the belts: Feed the anchored end of the belt up
through the buckle to form a loop . Pull the free end of the
belt . Repeat this procedure to tighten the other belt.
To loosen the belts: Feed the free end of the belt up through the
buckle to form a loop . Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the belt
to shorten the free end of the belt . Repeat this procedure to
loosen the other belt.
Please Note: After adjusting the belts to fit your child, make sure
you pull on them to be sure they are securely fastened.
Free End


7
7
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Power Switch
Music Switch
•Slide the power switch to any of five speed settings.
•Give the seat a light push to start the swinging motion.
Adjust the power switch to the desired swing motion setting.
Hint: As with most battery-powered swings, a heavier child will reduce
the amount of swinging motion on all settings. In most cases, the low
setting works best for a smaller child while the high setting works best for
a larger child.
•If swinging stops while using a lower setting, try a higher
setting. Give the seat a light push to start the swinging
motion again.
•Be sure to turn this product off when not in use. Slide the
power switch to the off setting .
•Slide the music switch to on with low volume ; on with
high volume or off .
•Attach the toys to any of the links on the swing arms or
the toybar.
Attach Toys to These Links
Starting the Swing Room-to-Room Portability
•To prevent serious injury or death from
falls and being strangled in the
restraint system, always use the
restraint system.
•It is dangerous to use this product on
an elevated surface.
WARNING
•Make sure your child is properly secured in the swing seat.
•Grasp both handles, as shown, and lift.
•Carefully carry the swing to another room. Be sure to set the
swing down on a non-elevated, flat surface.

8
8
•Lift the seat bottom.
LIFT
PRESS
•Press the frame release buttons on the inside of the frames
and push the front legs inward.
•Press the frame release buttons on the inside of the frames
and push the back legs inward.
The pad and soft toys are machine washable. Place the soft toys
in a pillow case. Wash the pad and toys separately in cold water
on the gentle cycle. Do not use bleach. Line dry. The frame can be
wiped clean using a mild cleaning solution and a damp cloth. Do
not immerse the frame.
To remove the pad:
•Lift the footrest and remove the pad lower pocket.
•Push the waist belts back through the pad.
•Slide the pad upper pocket off the seat back tube.
To re-assemble the pad:
•Refer to assembly steps 8 and 9.
Storage
Consumer Information
Care
Great Britain: Mattel UK Ltd. Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500302.
Australia
Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand
16-18 William Pickering Drive, Albany 1331, Auckland.
Asia
Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.