Big Lots SW-RK997 User manual

4PK STEEL CUSHIONED DINING CHAIR
ASSEMBLY INSTRUCTIONS
ITEM# SW-RK997
SKU# 810502963
DO NOT RETURN THIS PRODUCT TO THE STORE. FOR MISSING PARTS OR QUESTIONS TO THIS PRODUCT PLEASE CALL US AT 1-888-733-8169
OR EMAIL US AT customerservice [e-mail] OR customerservice [e-mail] OR customerservice [e-mail]
IMPORTANT :
Please read all the instructions and warnings before assembling . In order to make the whole product adjust to the best, please install all the screws on the product
before fully tighten, and note to put the washer to the screw before putting the screw into the screw hole.
WARNING :
Use the correct screws as indicated. All screws should be hand tighten until the complete piece is assembled ( This will make the
assembly process much easier ). Once the piece is fully assembled, then go back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product construction .
Keep assembly area at leat 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and use.
The chair is not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The chair is not a toy. Chair tested for use at weight of 250 lb (113.6kg). Improper use of this product or failure to use as directed may
result in injury. Not intended for commercial use.
CARE & MAINTENANCE
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE IN RAINING DAY.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushion to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and
water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Screws can be loosen over a peirod of usage, please check the screws
occasionally and re-tighten if necessary.

PARTS LIST FOR 1 CHAIR
NO. Part Qty Image NO. Part Qty Image
A1 Left Armrest 1D1 Cushion 1
A2 Right Armrest 1AA Screw (M6×20mm) Unit 10
B1 Chair Seat 1XX Wrench 1
C1 Chair Back 1
STEP 1 STEP 2
Insert 2 Screw (M6×20mm) Unit (AA) through each of the back-corners
of Chair Seat (B1) and into the screw-threading found on the legs of
Chair Back (C1). Do not tighten screws all the way until assembly is
completed.
Place Left Armrest (A1) on the left side of previously assembled
parts and Right Armrest (A2) on the right. Insert 2 Screw
(M6×20mm) Unit through each of the front-corners of Chair Seat
(B1) and into the screw-threading found on the legs of Armrests
(A1&A2). Do not tighten screws all the way until assembly is
completed.
STEP 3 STEP 4
Insert 2 Screw (M6×20mm) Unit through holes found underneath
Armrests (A1&A2) and into the screw-threading found on the sides of
Chair Back (C1). Tighten all screws left loose throughout assembly
process using Wrench (XX). Follow these steps to assemble the
remaining chairs for this set.
Place Cushion (D1) on chair seat once finished with assembly of
chairs.