Big Lots SW-RK922 User manual

3PC ALL WEATHER WICKER ROCKER SET
ASSEMBLY INSTRUCTION
ITEM# SW-RK922
SKU# 810502967
DO NOT RETURN THIS PRODUCT TO THE STORE. FOR MISSING PARTS OR QUESTIONS TO THIS PRODUCT PLEASE CALL US AT 1-888-733-8169
OR EMAIL US AT customerservice_0[email protected] OR custo[email protected]et OR customerservice_0[email protected]
IMPORTANT:
Please read all the instructions and warnings before assembling. In order to make the whole product adjust to the best, please install all the screws on the product
before fully tighten, and note to put the washer to the screw before putting the screw into the screw hole.
WARNING:
Use the correct screws as indicated. All screws should be hand tighten until the complete piece is assembled ( This will make the
assembly process much easier ). Once the piece is fully assembled, then go back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product construction.
Keep assembly area at leat 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and use.
The rocker is for sitting purpose only, is not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The rocker is not a toy. Rocker tested for use at weight of 250 lb (113.6kg). Improper use of this product or failure to use as directed may
result in injury. Not intended for commercial use.
CARE & MAINTENANCE
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE IN RAINING DAYS.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushion to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
ALL WEAHTER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and
water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Screws can be loosen over a peirod of usage, please check the screws
occasionally and re-tighten if necessary.

PARTS LIST FOR ROCKER
NO. Part Qty Image NO. Part Qty Image
ALeft Arm 1FRear Support 1
BRight Arm 1GLong Screw (M6x30MM) 8
CSeat Panel 1HSmall Screw(M6x20MM) 6
DBack Panel 1JWasher 12
EFront Support 1KWrench 1
STEP 1 STEP 2
Secure Seat panel (C) to Left Arm (A) and Right Arm (B) with 4 Long
Screw (G), 4 Washer (J) by using Wrench (K) . Secure Rear Support
(F) to Left Arm (A) and Right Arm (B) with 2 Screw (H) by using
Wrench (K) . Do not tighten all screws now.
Secure Front Support (E) to Left Arm (A) and Right Arm (B) with 4
Short Screw (H), 4 Washer (J) by using Wrench (K) . Do not tighten
all screws now.
STEP 3 STEP 4
Secure Back Panel (D) to Left Arm (A) and Right Arm (B) with 4
Long Screw (G), 4 Washer (J) by using Wrench (K) . Do not tighten
all screws now.
Verify the alignment and adjust, fully tighten all screws. Put cushions
on assembled chair.

PARTS LIST FOR TABLE
NO. Part Qty Image NO. Part Qty Image
ATable Top 1JWasher 8
BTable Leg 4KWrench 1
HScrew(M6x20MM) 8
STEP 1 STEP 2
Insert the 4 Table Leg (B) into the four leg hole that in the base of the
table. Do not tighten all screws now.
Secure 4 Table Leg (B) to Table Top (A) with 4 Screw (H) and 4
Washer (J) by using Wrench (K). Do not tighten all screws now.
STEP 3
Verify the alignment and adjust, fully tighten all screws.