Courtyard Creations RUS4265-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
RUS4265-WM
Do not discard any of the packaging until you have checked that you have all the parts
and pack of fittings.
Keep children away during assembly. This item contains small parts which can be
swallowed by children. Children should always be under direct adult supervision while
using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 7 COURTYARD CREATIONS INC.
!
!
!
!
STOP DON’T RETURN TO STORE!

PAGE 2 OF 7
STOP DON’T RETURN TO STORE!
A. Please read instructions thoroughly. Acquaint yourself with the inventory of
parts and the accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools
- Phillips Screwdriver(Not Included)
- Nut Wrench (See Part #31)
- Hex. Key Wrench (See Part #30)
C. Lay out all parts on a flat surface and identify them using the table below.
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
2
2
1
1
1
1
1
1
4
3
2
4
4
2
18
17
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
4
10
4
2
6
4
36
4
18
2
2
2
2
1
1
1
3
RUS4265-CS01
62RUS4265N102
62RUS4265N101
62RUS4265I102
RUS4265-CS02
RUS4265-CS03
RUS4265-CS04
62RUS416BH101
RUS484K-CS02
RUS484K-CS03
62RUS4265M101
RUS4265-CS05
62RUS4265H103
2800221038
180930201
17GC06042401
17C01A0721091Y4
17C01A0716072Y4
17C01A0714003Y4
17C01A0826011Y4
17C02A0712003Y4
17C17A1306001Y4
17FA05050401-Y4
17FA08060601-Y4
1800C23001
17D03A040401-Y4
1806616151401
1802612002
RTS423E-CS06
17KAA0201----Y4
17KAB1101----Y4
61R4265D00001BA
61R4265C00001BA
REAR UPRIGHT SUPPORT
FRONT UPRIGHT SUPPORT
LATERAL CROSS BRACE
REAR CROSS BRACE
RIGHT SEATARM
LEFT SEATARM
SEAT FRONT SUPPORT
SEAT REAR SUPPORT
SEATASSEMBLY
SWING ARM TUBE
FRONT/REAR CANOPY BRACE
SIDE CANOPY BRACE
LEG CAP
PLASTIC JOINT COVER
SUSPENSION SPRING
BOLT M6*60
BOLT M6*45
BOLT M6*40
BOLT M8*80
BOLT M6*35
SCREW ST4.2*16
WASHER d6.5*D16*1.2
WASHER d8.5*D17*1.6
PLASTIC NUT M6*P1.0
JAM NUT M8*1.25
PLASTIC WASHER
CANOPY/FRAME CONNECTOR
HEX.KEY WRENCH 6MM
NUT WRENCH 10&13MM
CANOPY
CUSHION
TOP CROSS BEAM
W/ADJUSTABLE TEETH
PLASTIC SCREW

STOP DON’T RETURN TO STORE!
PAGE 3 OF 7
Step A - 1
Step A - 2
Step A - 3
Step A - 4
Fig. A
Do not tighten bolts/nuts
after Step 1. Fasten
all bolts/nuts after Fig A.
ASSEMBLY (Note: For all nuts and bolts
fastening, always use a washer (#23 or #24)
between the tube and bolt or the tube and
nut.)
Step A - 1:
Insert the top cross beam w/adjustable teeth
(#1) into the upright supports (#2 and #3).
Fasten them by using bolts (#17), washers
(#23) and plastic nuts (#25). Repeat the
procedure for the other side. Do not tighten
bolts & plastic nuts yet.
Step A - 2:
Fasten the lateral cross braces (#4) to the
upright supports (#2 and #3) by using bolts
(#17), washers (#23) and plastic nuts (#25).
Repeat the procedure for the other side. Do
not tighten bolts & plastic nuts yet.
Step A - 3:
Fasten the rear cross brace (#5) to the rear
upright supports (#2) by using bolts (#17),
washers (#23) and plastic nuts (#25).
Tighten all of the bolts & plastic nuts now.
NOTE:
The label arrow mark on the rear cross
brace (#5) should be facing upwards.
Step A - 4:
Insert the leg caps (#14) to the rear and
front base feet.

PAGE 4 OF 7
STOP DON’T RETURN TO STORE!
Step B - 1
Step B - 2
Step B - 3
Step B - 4
Step B - 5
support brace
Fig. B
Step B - 1:
Insert the seat arms (#6 and #7) into the
seat supports (#8 and #9) and fasten them
by using plastic joint covers (#15), bolts
(#19), washers (#23), and plastic nuts (#25).
NOTE:
(1) The label marked “back” on the left seat
arm (#7) should coincide with the label
marked “back” on the seat rear support
(#9) to ensure proper assembly.
(2) The clip holders attached to the seat rear
support (#9) should be positioned on the
inside of the swing. The open side of the
clip holder should be facing upwards.
Step B - 2:
Open the seat assembly (#10) and attach
its back to the seat arms (#6 and #7) by
using bolt (#20), washers (#24), plastic
washer (#27), and jam nut (#26). Do the
same procedure for both sides.
Step B - 3:
Make sure that the support brace on the
back of the seat assembly (#10) is fully
inserted into the clip holders on the seat
rear support (#9).
Step B - 4:
Attach the swing arm tubes (#11) to the
right and left seat arms (#6 and #7) by
using bolts (#18), washers (#23), and
plastic nuts (#25). Do the same procedure
for both sides.
Step B - 5:
Hook the suspension spring (#16) into
the top of both swing arm tubes (#11). Do
the same procedure for both sides.

PAGE 5 OF 7
STOP DON’T RETURN TO STORE!
Fig. C
Fig. D
Step D - 1
Step D - 3
Step D - 4
Step D - 5
Step D - 2
Step C :
Hang the opposite ends of the suspension spring
(#16) into the holes located on the top cross beam
w/adjustable teeth (#1). Do the same procedure
for both sides.
WARNING:
Make sure that the ends of the suspension springs
(#16) go completely through the holes on the top
cross beam w/adjustable teeth (#1) and the swing
arm tubes (#11).
Step D - 1 & Step D - 2 :
Slide the canopy/frame connectors (#28) into
the side canopy braces (#13). Fasten them
together by using screws (#22) in the pre-drilled
holes. Ensure that the teeth on the canopy/frame
connectors are facing toward the inside of the
frame.
Step D - 3:
Insert the front/rear canopy braces (#12) into the
sleeves of the canopy (#32) on both sides.
Step D - 4:
Fasten the side canopy braces (#13) to the front/
rear canopy braces (#12) by using bolts (#21) on
both sides.
Step D - 5:
Velcro the canopy (#32) to the side canopy braces
(#13).

PAGE 6 OF 7
STOP DON’T RETURN TO STORE!
Fig. E
Fig. F
Fig. G G-1(seat) G-2(bed)
Step E :
Fasten the canopy/frame connectors (#28) to
the adjustable teeth on the top cross beam
w/adjustable teeth (#1) by using a plastic
screw (#29). Do this procedure for both sides.
Step F :
Place the cushions (#33) onto the seat
assembly (#10).
Double check to ensure that all of the bolts
have been completely tightened to assure
stability.
Step G :
Please make sure that the safety locks on
the seat rear support (#9) are fully locked
whenever the seat assembly is in a
swinging position. See Fig. G - 1 (seat).
To flatten the seat assembly, lift up the
safety lock and remove the support brace.
See Fig. G - 2 (bed) and Fig. H2.
Then, insert the support brace into the rear
cross brace (#5). Your seat assembly
should now be in a secured position and
not moving at all. See Fig. H3, Fig. H4,
and Fig. H5.

Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANYSMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULDYOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THEITEM TO THESTORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
PAGE 7 OF 7
STOP DON’T RETURN TO STORE!
Fig. H
Fig. H5
Fig. H1 Fig. H2 Fig. H3 Fig. H4
Step H :
The locking mechanism can also be used to
convert the seat assembly into a bed.
Note:
To avoid danger of suffocation, please keep
plastic bags or small parts away from babies
and children.
Cleaning and Maintenance
• Wash frame parts and fabric with mild soap and water, rinse thoroughly. Dry frame completely and allow the
fabric to drip dry.
• Do not use bleach, acid, or other solvents on the fabric or frame parts.
• In order to prolong the life and beauty of your swing, we recommend that the swing be stored in a dry area
when not in use. (For example, overnight or on rainy days)
• Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety
of your swing.
Special Warnings:
The user of this swing should always inspect it before each use.
1. It is essential to place the swing on level ground and not less than 6 feet from any obstruction such as
fences, garages, the house, overhanging branches, laundry lines, or electrical wires.
2. Check all bolts and nuts for tightness on a regular basis.
3. Make sure the suspension springs are always properly hooked before each use.
4. Oil all metallic moving parts during usage season.
5. Always remove the canopy in heavy wind conditions, otherwise the canopy may tip over and may cause
damage to its parts.
6. The manufacturer will not accept responsibly for unauthorized repair or modifications to the swing.
7. Weight limit 750 lbs.