Billion BiPAC VGL User manual

BiPAC 7402VL/VGL/VGP
VoIP/(802.11g) ADSL2+ Router
Quick Start Guide

Billion VoIP/(802.11g) ADSL2+ Router
For more detailed instructions on configuring and usin
g
the Billion VoIP/(802.11g) ADSL2+ Router, please refer to
the on-line manual.
Package Contents
VoIP/(802.11g) ADSL2+ Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console (PS2-RS232) Cable
AC-DC power adapter (12VDC, 1.2A)
This Quick Start Guide
Warning
 Do not use this router in high humidity or high
temperatures.
 Do not use the same power source for this router as othe
r
equipment.
 Do not open or repair the case yourself. If this router is too
hot, turn off the power immediately and have it repaired at a
qualified service center.
 Avoid using this product and all accessories outdoors.
A
ttention
 Place this router on a stable surface.
 Only use the power adapter that comes with the package.
Using a different voltage rating power adaptor may damage
this router.
1

Quick Start Guide
The Front LEDs
LED Meaning
1 PWR Lit when power is ON.
2 SYS Lit when the system is ready.
3 - 5 LAN Port
1X — 3X
(RJ-45 connector)
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
7 WLAN
(BiPAC 7402VGL/VGP only) Lit green when the wireless connection is established.
Flashes when sending/receiving data.
8 – 9 Phone 1X — 2X
(RJ-11 connector) Lit green when the phone is off-hook.
10 LINE
(BiPAC 7402VGP only) Lit when the inbound and outbound calls transmitted
through PSTN.
11 VoIP Lit when SIP registration is OK.
12 PPP / MAIL
Lit steady when there is a PPPoA / PPPoE connection.
Lit and flashed periodically when there is email in the Inbox.
13 ADSL Lit when successfully connected to an ADSL DSLAM
(“linesync”).
2

Billion VoIP/(802.11g) ADSL2+ Router
The Rear Ports
BiPAC 7402VL
3
BiPAC 7402VGL
BiPAC 7402VGP
1
3
2
4
3
5
6
3
5
6
7
1
2
4
1
2
4
5
6
78
9
7
8

Quick Start Guide
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 RESET
After the device is powered on, press it to reset the
device or restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this
is used when you can not login to the router, e.g. forgot
the password)
4 LAN 1X — 3X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one
of the four LAN ports when connecting to a PC or an
office/home network of 10Mbps or 100Mbps.
5 CONSOLE Connect a PS2/RS-232 cable to this port when
connecting to a PC’s RS-232 port (9-pin serial port).
6
Phone
1X ─2X
(RJ-11 connector)
Connect RJ-11 cable to this port when connecting to an
analog phone set.
7 ADSL Connect the supplied RJ-11 (“telephone”) cable to this
port when connecting to the ADSL/telephone network.
8
Antenna
(BiPAC 7402VGL/VGP only)
Connect the detachable antenna to this port.
9
LINE
(BiPAC 7402VGP only)
Connect RJ-11 cable to this port when connecting to the
telephone wall jack.
4

Billion VoIP/(802.11g) ADSL2+ Router
Connecting Your ADSL Router
1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone (ADSL) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit.
4. Connect an RJ11 cable to VoIP port when connecting to an analog phone set.
5. Connect RJ-11 cable to LINE Port when connecting to the telephone wall jack (BiPAC
7402VGP only).
BiPAC 7402VL/VGL
(802.11g is not supported in BiPAC 7402VL)
Connect more
computers
Switching/
HUB
Analog Phone
BiPAC 7402VGP
Analog Phone
ADSL
Splitte
r
ADSL Phone
Line
Connect more
computers
Switching/
HUB
5

Quick Start Guide
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6

Billion VoIP/(802.11g) ADSL2+ Router
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
7

Quick Start Guide
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
8