Billion VoIP/(802.11g) ADSL2+ Router BiPAC 7300VGP User manual

BiPAC 7300VP/ 7300VGP
VoIP/(802.11g) ADSL2+ Router
Quick Start Guide

Billion BiPAC 7300VGP Series ADSL2+ Router
For more detailed instructions on configuring and using
the VoIP/802.11g ADSL2+ Router, please refer to the
on-line manual.
Package Contents
VoIP/(802.11g) ADSL2+ Router
CD-ROM containing the on-line manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1.2A)
This Quick Start Guide
Warning
 Do not use the BiPAC 7300VGP Series in high humidity or high
temperatures.
 Do not use the same power source for the BiPAC 7300VGP
Series as other equipment.
 Do not open or repair the case yourself. If the BiPAC 7300VGP
Series are too hot, turn off the power immediately and have it
repaired at a qualified service center.
 Avoid using this product and all accessories outdoors.
A
ttention
 Place the BiPAC 7300VGP Series on a stable surface.
 Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
1

Quick Start Guide
The Front LEDs
LED Description
1 PWR：Lights when the power is ON.
2 SYS：Lights when the system is ready.
3-6 LAN Port
1-4：
Steady glow when connected to an Ethernet device.
Glows green for 100Mbps; Orange for 10Mbps.
Blinking light when data is Transmitted / Received.
7 WLAN：
(7300VGP
only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
8-9 Phone：Lit green when the phone is off-hook.
10 LINE：Lit when the inbound and outbound calls transmitted
through PSTN.
11 VoIP：Lit when SIP registration is OK.
12 PPP：Steady glow when there is a PPPoA / PPPoE connection.
13 ADSL：Lights when successfully connected to an ADSL DSLAM
(linesync).
2

Billion BiPAC 7300VGP Series ADSL2+ Router
The Rear Ports
3
8 67 5 43 1 2
Port Description
1 Power
Switch Power ON/OFF switch.
2 PWR Connect the supplied power adapter to this jack.
3 RESET
After the router is powered on, press this recessed button using
the end of paper clip or other small pointed object to reset the
router or to restore it to factory default settings.
1. Recovery procedures for non-working routers (e.g. after a
failed firmware upgrade flash):
2. Recovery procedures for a lost web interface password:
4 LAN Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the
four LAN ports when connecting to a PC or an office/home
network of 10Mbps or 100Mbps.
5 Phone Connect RJ-11 cable to this port when connecting to an analog phone
set.
6 LINE Connect RJ-11 cable to this port when connecting to the telephone
wall jack
7 ADSL Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
8 Antenna
(7300VGP
only) Connect the detachable antenna to this port.

Quick Start Guide
Connecting BiPAC 7300VGP series
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
4. Connect an RJ11 cable to VoIP port when connecting to an analog phone set.
5. Connect an RJ11 cable to LINE port when connecting to the telephone wall jack
4

Billion BiPAC 7300VGP Series ADSL2+ Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
5

Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6

Billion BiPAC 7300VGP Series ADSL2+ Router
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
7

Quick Start Guide
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Protocols tab.
2. Select TCP/IP Protocol and click
Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
8