Billion BiPAC 7560G User manual

BIPAC-7560G
Powerline/11g ADSL VPN Firewall Router
Quick Start Guide

Billion BIPAC-7560G Powerline/11g ADSL VPN Firewall Router
For more detailed instructions on configuring and usin
g
the Powerline/11g ADSL VPN Firewall Router, pleas
e
refer to the on-line manual.
Package Contents
BIPAC-7560G Powerline/11g ADSL VPN Firewall Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console (PS2-RS232) Cable
Power Adapter
This Quick Start Guide
Warning
 Do not use the BIPAC-7560G ADSL VPN Firewall Router in high
humidity or high temperatures.
 Do not use the same power source for the BIPAC-7560G ADSL
VPN Firewall Router as other equipment.
 Do not open or repair the case yourself. If the BIPAC-7560G ADSL
VPN Firewall Router is too hot, turn off the power immediately and
have it repaired at a qualified service center.
 Avoid using this product and all accessories outdoors.
A
ttention
 Place the BIPAC-7560G ADSL VPN Firewall Router on a stable
surface.
 Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
1

Quick Start Guide
The Front LEDs
LED Meaning
1 PWR Lit when power is ON.
2 SYS Lit when the system is ready.
3 LAN port 1 Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps
Blinking when data is transmitted/received.
4 LAN port 2 Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps
Blinking when data is transmitted/received.
5 LAN port 3 Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps
Blinking when data is transmitted/received.
6 LAN port 4 Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps
Blinking when data is transmitted/received.
7 WLAN Lit green when the wireless connection is established. Flashes
when sending/receiving data.
8 Powerline Lit when HomePlug interface ready.
Blinking when data is transmitted/received.
10 MAIL Flash when there is Email in your configured Email account.
11 PPP Lit when there is a PPPoA / PPPoE connection.
13 ADSL Lit when successfully connected to an ADSL DSLAM (“linesync”).
2

Billion BIPAC-7560G Powerline/11g ADSL VPN Firewall Router
The Rear Ports
6
5
4
32
1
Port Meaning
1 LINE Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
2 CONSOLE Connect a PS2/RS-232 cable to this port when connecting to a
PC’s RS-232 port (9-pin serial port).
3 LAN
1X — 4X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the
four LAN ports when connecting to a PC or an office/home
network of 10Mbps or 100Mbps.
4
RESET
After the device is powered on, press it to reset the device or
restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this is used
when you cannot login to the router. E.g. forgot the password)
5 PWR Connect the supplied power adapter to this jack.
6 Power Switch Power ON/OFF switch
3

Quick Start Guide
Connecting Your ADSL Router
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, WLAN LEDs are lit steadily and that the relevant LAN LED is lit.
4

Billion BIPAC-7560G Powerline/11g ADSL VPN Firewall Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
5

Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6

Billion BIPAC-7560G Powerline/11g ADSL VPN Firewall Router
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
7

Quick Start Guide
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and click
Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
8