Bionaire BCH4267 User manual

CERAMIC HEATER
WITH COLOUR
CHANGING GRILL
BCH4267
INSTRUCTION MANUAL
GUARANTEE
PLEASE KEEP YOUR RECEIPT AS THIS WILL
BE REQUIRED FOR ANY CLAIMS UNDER THIS
GUARANTEE.
•This product is guaranteed for 2 years.
•In the unlikely event of breakdown, please take
it back to the place of purchase, with your till
receipt and a copy of this guarantee.
•The rights and benefits under this guarantee
are additional to your statutory rights which
are not affected by this guarantee.
• Holmes Products (Europe) Ltd. undertakes
within the specific period, to repair or replace
free of charge, any part of the appliance
found to be defective provided that:
•We are promptly informed of the defect.
•The appliance has not been altered in any
way or subjected to misuse or repair by a
person other than a person authorised by
Holmes Products (Europe) Ltd.
• No rights are given under this guarantee to a
person acquiring the appliance second hand
or for commercial or communal uses.
• Any repaired or replaced appliance will be
guaranteed on these terms for the remaining
portion of the guarantee.
THIS PRODUCT IS MANUFACTURED TO
COMPLY WITH THE E.E.C. DIRECTIVES
2006/95/EC, 2004/108/EC AND 2006/42/EC.
Waste electrical products should
not be disposed of with
Household waste. Please
recycle where facilities exist.
Check on the following website
for further recycling and WEEE
information: www.bionaire.com
or e-mail
[email protected].
Holmes Products (Europe) Ltd
1 Francis Grove
London SW19 4DT
England
Fax: [phone]
Email: [email protected]
Website address: www.bionaire.com
UK - Free phone Customer Service Helpline – 0800 052 3615
© 2007 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
9100020008710
BCH4267IUK07EM1
BCH4267IUK07EM1.qxd 10/9/07 22:25 Page 1

DESCRIPTION
A. Thermostat Control
B. Selector Control/ Mode
HI (II) LO (I) OFF (O)
C. Power Indicator Light
OPERATING INSTRUCTIONS
Setting the Power Level
1. For heater operation, turn Thermostat Control
(A) to HI ( ) (See Figure 2).
2. Turn Selector Control (B) to II or I.
NOTE: Power Indicator Light (C) will illuminate
when heater is plugged into the mains.
Setting the Thermostat
The thermostat maintains the desired
temperature level by switching on and off.
1. Turn the Thermostat Control all the way to
the right (clockwise) to the maximum
temperature level HI ( ).
2. When the desired temperature is reached,
slowly turn the Temperature Control back
(counter-clockwise) until the heater switches off.
3. The control will now automatically maintain
the pre-set temperature level by turning the
heater ON and OFF.
4. The Power Indicator Light will remain lit to
indicate the heater in on.
NOTE: It is normal for the heater to cycle ON
and OFF as it maintains the preset temperature.
To prevent the unit from cycling, you need to
change the thermostat setting.
FROST-GUARD SETTING
This special setting will automatically turn on the
heater if the room’s temperature reaches freezing.
To set, turn the Thermostat Control all the way
to LO ( ), and turn the Selector Control to either
HI (II) or LO (I).
COLOUR CHANGING DISPLAY
Your heater features the revolutionary
technology and safety of Colour Changing
Display. As your heater warms up, parts of, the
front grill will change colour – a visual reminder
that the grill is warm and the heater is on. The
exact timing of the colour change may vary.
When the heater is turned off, the grill will return
to its original colour , thus indicating the grill is
cool to the touch. This may take up to an hour
depending on the environment surrounding the
heater and the cooling down time of the
element.
NOTE: If left in extreme cold temperatures
(-22° F/-30°C) the Colour Changing Display may
not perform. The heater itself will function
normally. Store heater in a cool and dry location.
NOTE: The colour changing effect may wear off
after continuous, heavy use of the heater or in
time. The heater will continue to operate
normally.
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-
advanced, safety system that requires the user
to reset the heater if there is a potential overheat
situation. When a potential overheat temperature
is reached, the system will automatically shut
the heater off. It can only resume operation
when the user resets the unit.
To Reset the Heater:
1. Turn MODE to (O) and Thermostat to HI ( ).
2. Unplug unit, wait 30 minutes.
3. Plug in and turn ON.
Safety Back-Up Fuse
In the unlikely case the heater does not respond to
an overheat situation, the safety back-up fuse will
engage. In this case, the heater will not reset.
Please contact your local service number on the
back of the manual for advice.
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating, do
not cover the heater ( ).
3. DO NOT position the heater directly under a
power socket.
4. Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its
service agent or similarly qualified person in
order to avoid hazard. The heater contains
no user serviceable parts. Should the product
suffer damage or breakdown, it must be returned
to the manufacturer or their service agent.
ENGLISH
BCH4267
Fig. 1
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. Do not use this heater with a programmer,
timer or any other device that switches the
heater on automatically, since a fire risk exists if
the heater is covered or positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT position where it can be touched by
children, especially the very young.
10.DO NOT use this heater outdoors.
11. Allow a safe area around the heater away
from furniture or other objects; at least 50 cm
from the top and sides and 200 cm at the front.
12.Do not use this heater when it is lying on its side.
13.DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when gluing
or varnishing parquet floors, PVC etc.).
14.DO NOT insert any objects into the heater.
15.Keep the mains cord at a safe distance from
the main body of the heater.
16.If overheating should occur, the built-in
overheating safety device will switch off the
heater.
17.Do not place the cord under a rug.
18.The heater is to be installed so that switches
and other controls cannot be touched by a
person in the bath.
19.Avoid the use of an extension cord because
it may cause the heater to overheat.
20.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with
the appliance.
For U.K. and Ireland only:
If the plug is not suitable for the socket outlets in
your home, it can be removed and replaced by
a plug of the correct type. Please refer to
"Installation of a plug" below.
Installation of a plug Applicable to
U.K. and Ireland
This product is fitted with a 13A plug complying to
BS1363. If this plug is unsuitable or needs to be
replaced, please note the following:
The wires in the mains lead are coloured as
such:
BROWN - LIVE
BLUE - NEUTRAL
Please note that the colour of these mains wires
may not correspond with the colour markings
that identify the terminals in your plug. Please
proceed as follows:
The BROWN coloured wire must be connected
to the terminal, which is marked with the letter
"L" or is coloured RED.
The BLUE coloured wire must be connected to
the terminal, which is marked with the letter "N"
or is coloured BLACK.
DO NOT CONNECT either of these wires to the
earth terminal in the plug. The earth terminal plug
is marked with the letter "E", or with the earth
symbol or coloured GREEN and YELLOW.
NOTE: If the terminals in the plug are not
marked or if you are unsure or in doubt about
the installation of the plug please contact a
qualified electrician. If a 13A 3-pin plug is fitted,
it must be an ASTA approved plug, conforming
to BS1363 standard. Replacement 13A fuses
must be BSI or ASTA BS1362 approved.
Fig. 2
B
C
A
BC
A
BCH4267IUK07EM1.qxd 10/9/07 22:25 Page 4