Bionaire BCH4821 User manual

person acquiring the appliance second hand
or for commercial or communal uses.
•Any repaired or replaced appliance will be
guaranteed on these terms for the remaining
portion of the guarantee.
THIS PRODUCT IS MANUFACTURED TO
COMPLY WITH THE E.E.C. DIRECTIVES
73/23/EEC, 89/336/EEC AND 98/37/EEC.
Waste electrical products should not
be disposed of with Household
waste.
Please recycle where facilities
exist.Check on the following website
for further recycling and WEEE infor-
mation: www.bionaire.com/europe or
e-mail [e-mail]
CERAMIC Heater
with ViziHeatTM
BCH4821
®
Holmes Products (Europe) Ltd
1 Francis Grove
London SW19 4DT
England
Fax: [phone]
Email: [email protected]
Website address: www.bionaire.com/europe
UK - Free phone Customer Service Helpline – 0800 052 3615
9100020007251
BCH4821IUK06EM2
®
INSTRUCTION MANUAL
© 2006 JCS/THG, LLC
Bionaire® , the Bionaire logoTM and ViziHeatTM are trademarks of JCS/THG, LLC.
BCH4821IUK06EM2 V.qxd 7/5/06 11:15 Page 1

Fig. 1
BCH4821 3. DO NOT position the heater directly under a
power socket.
4. Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its serv-
ice agent or similarly qualified person in order
to avoid hazard. The heater contains no user
serviceable parts. Should the product suffer
damage or breakdown, it must be returned to
the manufacturer or their service agent.
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. Do not use this heater with a programmer,
timer or any other device that switches the
heater on automatically, since a fire risk
exists if the heater is covered or positioned
incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT position where it can be touched by
children, especially the very young.
10. DO NOT use this heater outdoors.
11. Allow a safe area around the heater away
from furniture or other objects; at least 50 cm
from the top and sides and 200 cm at the
front.
12. Do not use this heater when it is lying on its
side.
13. DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when gluing
or varnishing parquet floors, PVC etc).
14. DO NOT insert any objects into the heater.
15. Keep the mains cord at a safe distance from
the main body of the heater.
16. If overheating should occur, the built-in
overheating safety device will switch off the
heater.
17. Do not place the cord under a rug.
18. The heater is to be installed so that switches
and other controls cannot be touched by a
person in the bath.
19. Avoid the use of an extension cord because it
may cause the heater to overheat.
For U.K. and Ireland only:
If the plug is not suitable for the socket outlets in
your home, it can be removed and replaced by a
plug of the correct type. Please refer to
"Installation of a plug" below.
Installation of a plug
Applicable to U.K. and Ireland
The wires in the mains lead are coloured as such:
BROWN - LIVE
BLUE - NEUTRAL
Please note that the colour of these mains wires
may not correspond with the colour markings
that identify the terminals in your plug.
Please proceed as follows:
The BROWN coloured wire must be connected
to the terminal, which is marked with the letter
"L" or is coloured RED.
The BLUE coloured wire must be connected to
the terminal, which is marked with the letter "N"
or is coloured BLACK.
DO NOT CONNECT either of these wires to the
earth terminal in the plug. The earth terminal
plug is marked with the letter "E", or with the
earth symbol or coloured GREEN, or
GREEN and YELLOW.
NOTE: If the terminals in the plug are not
marked or if you are unsure or in doubt about the
installation of the plug please contact a qualified
electrician. If a 13A 3-pin plug is fitted, it must be
an ASTA approved plug, conforming to BS1363
standard. Replacement 13 A fuses must be BSI
or ASTA BS1362 approved.
GUARANTEE
PLEASE KEEP YOUR RECEIPT AS THIS WILL
BE REQUIRED FOR ANY CLAIMS UNDER
THIS GUARANTEE
•Your heater is guaranteed for 2 years.
•In the unlikely event of breakdown, please
take your heater back to the place of purchase,
with your till receipt and a copy of this guarantee.
•The rights and benefits under this guarantee
are additional to your statutory rights which
are not affected by this guarantee.
•Holmes Products Europe undertakes within
the specific period, to repair or replace free of
charge, any part of the appliance found to be
defective provided that:
•We are promptly informed of the defect.
•The appliance has not been altered in any
way or subjected to misuse or repair by a
person other than a person authorised by
Holmes Products Europe.
•No rights are given under this guarantee to a
DESCRIPTIONS
A. Mode Control
B. Thermostat Control
C.Front Grill
D.Power Light
E. Integrated Carry Handle
F. Oscillation Button
G.Front Panel
OPERATING INSTRUCTIONS
Setting the Mode
1. For heater operation, turn the Mode Control (A)
to the desired setting:
I- Low setting (1000 Watts)
II - High setting (2000 Watts)
2. For fan-only operation, without any heat output,
turn the Mode Control (A) to the FAN ( ) set-
ting. If the fan does not turn on, turn the
Thermostat Control to the maximum position.
3. The Power Light (D) will remain lit during
operation.
Setting the Thermostat
The thermostat maintains the desired tempera-
ture level by switching on and off.
1. Turn the Thermostat Control all the way to the
right (clockwise) to the maximum temperature
level.
2. When the desired temperature is reached,
slowly turn the Temperature Control back
(counter-clockwise) until the heater switches off.
3. The control will now automatically maintain the
pre-set temperature level by turning the heater
ON and OFF.
NOTE: It is normal for the heater to cycle ON
and OFF as it maintains the preset tempera-
ture. To prevent the unit from cycling, you
need to change the thermostat setting.
Oscillation Instructions
Press Oscillation Button (F) ( ) to start oscilla-
tion and press Button (F) again to stop the oscil-
lation.
VIZIHEATTM COLOUR CHANGING DISPLAY
Your heater features the revolutionary technology
and safety of ViziHeat™ Colour Changing
Display. As your heater warms up, parts of the
front grill will change colour - a visual reminder
that the grill is warm and the heater is on. The
exact timing of the colour change may vary.
When the heater is turned off, the grill will return
to its original colour, thus indicating the grill is
cool to the touch. This may take up to an hour
depending on the environment surrounding the
heater and the cooling down time of the
element.
NOTE: If left in extreme cold temperatures
(- 22° F/-30°C) the ViziHeat™ color changing
display may not perform. The heater itself will
function normally. Store heater in a cool and dry
location.
NOTE: The ViziHeat™ colour changing effect
may wear off after continuous, heavy use of the
heater or in time. The heater will continue to
operate normally.
FROST-GUARD SETTING
This special setting will automatically turn on the
heater if the room’s temperature reaches
freezing. To set, turn the Thermostat Control all
the way to minimum temperature level, and turn
the Mode Control to either HI (II) or LO (I).
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically
advanced, safety system that requires the user
to reset the heater if there is a potential overheat
situation. When a potential overheat temperature
is reached, the system will automatically shut the
heater off. It can only resume operation when the
user resets the unit.
To reset the heater
1. Turn MODE to OFF ( ) and THERMOSTAT
to MAX ( ).
2. Unplug unit, wait 30 minutes.
3. Plug in and turn ON.
Tip-Over Protection
When the unit is accidentally knocked over, it will
instantly shut off. To reset, simply place the
heater in an upright position.
Safety Back-Up Fuse
In the unlikely case the heater does not respond
to an overheat situation, the safety back-up fuse
will engage. In this case, the heater will not
reset. Please contact your local service number
on the back of the manual for advice.
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including the
following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating, do
not cover the heater .
ENGLISH
D
AB
C
E
13 amp
F
B
A
G
BCH4821IUK06EM2 V.qxd 7/5/06 11:15 Page 4