Biostar BIH11-IHP User manual

FCC Informaon and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. There is no guarantee that interference
will not occur in a parcular installaon.
The vendor makes no representaons or warranes with respect to the contents here and
specially disclaims any implied warranes of merchantability or tness for any purpose. Further
the vendor reserves the right to revise this publicaon and to make changes to the contents here
without obligaon to nofy any party beforehand.
Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the
vendor’s approval in wring.
The content of this user’s manual is subject to be changed without noce and we will not be
responsible for any mistakes found in this user’s manual. All the brand and product names are
trademarks of their respecve companies.
Dichiarazione di conformità sinteca
Ai sensi dell’art. 2 comma 3 del D.M. 275 del
30/10/2002
Si dichiara che questo prodoo è conforme
alle normave vigen e soddisfa i requisi
essenziali richies dalle direve
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaraon of conformity
We declare this product is complying with the
laws in force and meeng all the essenal
requirements as specied by the direcves
2004/108/CE, 2006/95/CE and 1999/05/CE
whenever these laws may be applied

2 | Table Of Contents
BIH11-IHP User’s Manual
Table Of Contents
FCC Informaon and Copyright ������������������������������������������������������������������������������� 1
Chapter 1: Introducon������������������������������������������������������������������������������������������� 3
1.1 Before You Start.................................................................................................................. 3
1.2 Specicaons...................................................................................................................... 4
1.3 Rear Panel Connectors........................................................................................................ 6
1.4 Motherboard Layout........................................................................................................... 7
Chapter 2: Hardware installaon����������������������������������������������������������������������������� 8
2.1 Central Processing Unit (CPU)............................................................................................. 8
2.2 Install a Heatsink............................................................................................................... 10
2.3 Connect Cooling Fans ....................................................................................................... 11
2.4 Installing System Memory ................................................................................................ 11
2.5 Expansion Slots ................................................................................................................. 13
2.6 Jumper & Switch Seng................................................................................................... 14
2.7 Headers & Connectors...................................................................................................... 14

Chapter 1: Introducon | 3
BIH11-IHP User’s Manual
Chapter 1: Introducon
1�1 Before You Start
Thank you for choosing our product. Before you start installing the motherboard, please make
sure you follow the instrucons below:
• Prepare a dry and stable working environment with sucient lighng.
• Always disconnect the computer from power outlet before operaon.
• Before you take the motherboard out from an-stac bag, ground yourself properly
by touching any safely grounded appliance, or use grounded wrist strap to remove the
stac charge.
• Avoid touching the components on motherboard or the rear side of the board unless
necessary. Hold the board on the edge, do not try to bend or ex the board.
• Do not leave any unfastened small parts inside the case aer installaon. Loose parts
will cause short circuits which may damage the equipment.
• Keep the computer from dangerous area, such as heat source, humid air and water.
• The operang temperatures of the computer should be 0 to 45 degrees Celsius.
• To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
Note
»
»The package contents may be dierent due to the sales region or models in which it was sold. For
more informaon about the standard package in your region, please contact your dealer or sales
representave.

4 | Chapter 1: Introducon
BIH11-IHP User’s Manual
1.2 Specifications
Specicaons
CPU Socket 1151 for 6th & 7th Gen Intel® Core™ i7/i5/i3 / Penum / Celeron processor
Maximum CPU TDP (Thermal Design Power): 65Wa
Chipset Intel® H110
Graphic
LAN Controller: 2x RTL8111H
Audio Codec: ALC662
Audio Amplier: ALC105
DDI to VGA transmier: RTD2168-CG
EDP to LVDS: RTD2136R
Super IO: IT8786 (ITE)
Main Memory 2x 260 pins socket support DDR4 2133 SO-DIMM , up to 32GB
SATA 3x SATAIII 6Gb/s connector
1x Full Size MiniPCIE, Support mSATA
Ethernet 2x Realtek RTL8111H
10 / 100 / 1000 Mb/s auto negoaon, Half / Full duplex capability
Sound Codec Realtek ALC662+ALC105
Expansion Slots 1x PCI-E x16 Slot
1x mini PCI-E slot half size, support PCIe + USB interface
Graphic Intel® Integrated Graphics
Rear I/O
1x PS/2 - Keyboard Port
1x PS/2 - Mouse Port
1x DB9 connector
1x HDMI connector (4096 x 2160@24Hz)
1x VGA connector
1x DVI connector (1920 x 1200 @60Hz max)
2x LAN Port
2x USB3.1(Gen1) connector
2x USB2.0 connector
3x Audio jacks, support Line In/Line out/Mic
On Board Connectors
& Headers
Expansion slots:
2x 260 pins socket support DDR4 2133 SO-DIMM
3x 1* 7 pins SATA connector
1x Half size miniPCIE slot for PCIE+USB
1x Full size connector, support mSATA
Display:
1x 2* 20 pins(1.0) - header for LVDS colay with eDP
1x 1* 3 pins - header for backlight mode select (18/24bits)
1x 1* 3 pins(2.0) header for LCD panel power (3.3/5V)
1x 1* 3 pins(2.0) header for LCD backlight power (5V/12V)
1x 1* 6 pins header for LED driver
1x 2* 8 pins VGA header
Speaker:
2x 1* 2 pins(2.0) pitch wafer box pin-header for Speaker
1x Buzzer
Serial Ports:
5x 2* 3 pins header for 5V/12V/RI, default RI
5x 2* 5 pins 2.0 pitch pin header for RS232
1x 2* 3 pins 2.0 pitch pin header for COM1 RS232/422/485 change mode Jumper
1x 2* 6 pins 2.0 pitch pin header for COM1 RS232/422/485 change single Jumper
USB:
1x 2* 5 pins(2.0) USB2.0 header
1x 2* 10 pins USB3.0 header
1x 1* 4 pins USB2.0 header for Touch
Power:
1x 2* 10 pins ATX power connector
1x 2* 2 pins ATX power connector
2x 1* 4 pins(2.0) header for 5V/12V output (HDD Power) for open frame PSU
1x 1* 3 pins header for AT/ATX power select jumper
»
»Connued on Next Page

Chapter 1: Introducon | 5
BIH11-IHP User’s Manual
Specicaons
On Board Connectors
& Headers
Fan:
2x 1* 4pins(2.54) header for CPU/System fan (Smart Fan)
Others:
1x 2* 7pins header for TPM module
1x 2* 5pins (2.0) DIO header (by BIOS seng)
1x 1* 3pins(2.0) header clear CMOS
1x 2* 5pins header for power buon, Reset buon, HDD Led, power LED, Reset LED
Dimensions Mini-ITX From Factor, 170 mm (W) x 170 mm (L)
Operaon Temperature 0°C ~ 60°C
Storage Temperature -10°C ~ 70°C
Relave Humidity 5% ~ 90% (non-condensing)
ESD Contact with 4Kv, Air with 8Kv, Class A
Watchdog Timer Yes (65536 segments),
Reset; 1 sec.~255 min. and 1 sec. or 1 min. /step
RoHS Compliant Yes
OS Support Windows 7, Windows 8.1, Windows 10
We reserve the right to add or remove support for any OS with or without noce.

6 | Chapter 1: Introducon
BIH11-IHP User’s Manual
1�3 Rear Panel Connectors
COM1: Serial port Connectors (RS-232/RS422/RS485)
15
69
RS-232 (Default) RS-422* RS-485*
Pin Assignment
1 Carrier detect (DCD) 422 TXD- 485 DATA-
2 Received data (RXD) 422 TXD+ 485 DATA+
3Transmied data (TXD) 422 RXD+ NC
4 Data terminal ready (DTR) 422 RXD- NC
5 Signal ground (GND) GND GND
6 Data set ready (DSR) NC NC
7 Request to send (RTS) NC NC
8 Clear to send (CTS) NC NC
9*RI, 5V, 12V selected by
(selected by JP1 seng) NC NC
Note
»
»COM1 (RS-232/422/485) & COM2 (RS-232) selecon is controlled by JSEL1/ JSEL2.

Chapter 1: Introducon | 7
BIH11-IHP User’s Manual
1.4 Motherboard Layout
Note
»
» represents the 1st pin.

8 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
Chapter 2: Hardware installaon
2.1 Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard
Note
»
»Remove Pin Cap before installaon, and make good preservaon for future use. When the CPU is
removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged.
»
»The motherboard might equip with two dierent types of pin cap. Please refer below instrucon to
remove the pin cap.
Step 2: Pull the socket locking lever out from the socket and then raise the lever up.
Step 3: Remove the Pin Cap.

Chapter 2: Hardware installaon | 9
BIH11-IHP User’s Manual
Step 4: Hold processor with your thumb and index ngers, oriented as shown. Align the
notches with the socket. Lower the processor straight down without lng or sliding the
processor in the socket.
Note
»
»Ensure that you install the correct CPU designed for LGA1151 socket.
»
»The CPU ts only in one correct orientaon. Do not force the CPU into the socket to prevent
damaging the CPU.
Step 5: Hold the CPU down rmly, and then lower the lever to locked posion to complete the
installaon.

10 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
2.2 Install a Heatsink
Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four
fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest
to the CPU fan connector.
Step 2: Press down two fasteners at one me in a diagonal sequence to secure the CPU fan
assembly in place. Ensure that all four fasteners are secured.
Note
»
»Do not forget to connect the CPU fan connector.
»
»For proper installaon, please kindly refer to the installaon manual of your CPU heatsink.

Chapter 2: Hardware installaon | 11
BIH11-IHP User’s Manual
2.3 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and connector
may be dierent according to the fan manufacturer. Connect the fan cable to the connector
while matching the black wire to pin#1.
CPU_FAN1: CPU fan header
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)
SYS_FAN1: System fan header
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)
Note
»
»System Fan Headers support 4-pin head connectors. When connecng with wires onto connectors,
please note that the red wire is the posive and should be connected to pin#2, and the black wire is
Ground and should be connected to GND.
2.4 Installing System Memory
DDR4 Modules

12 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot
such that the notch on the DIMM matches the break on the slot.
Step 2: Insert the DIMM vercally and rmly into the slot unl the retaining clips snap back in
place and the DIMM is properly seated.
Note
»» If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
Memory Capacity
DIMM Socket Locaon DDR4 Module Total Memory Size
DIMMA1 4GB/8GB/16GB Max is 32GB.
DIMMA2 4GB/8GB/16GB
Note
»
»When installing more than one memory module, we recommend to use the same brand and
capacity memory on this motherboard.

Chapter 2: Hardware installaon | 13
BIH11-IHP User’s Manual
2.5 Expansion Slots
PEX16_1: PCI-Express x16 Slot (x16 speed)
• PCI-Express 3.0 compliant.
• Theorecal maximum bandwidth using two slots simultaneously is 16GB/s for each slot,
a total of 32GB/s.
2.6 Jumper & Switch Setting
Jumper Seng
The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the
jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin 1-2 closed
JCMOS1: Clear CMOS Jumper
Placing the jumper on pin2-3 allows user to restore the BIOS safe seng and the CMOS data.
Please carefully follow the procedures to avoid damaging the motherboard.
Pin 1-2 Close: Normal Operaon (Default)
Pin 2-3 Close: Clear CMOS data
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for ve seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.

14 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
2.7 Headers & Connectors
JATXPWR1: ATX Power Source Connector
For beer compability, we recommend to use a standard ATX 20-pin power supply for this
connector. Make sure to nd the correct orientaon before plugging the connector.
Pin Assignment Pin Assignment
1 3.3V 11 3.3V
2 3.3V 12 -12V
3 Ground 13 Ground
4 5V 14 PS_ON
5 Ground 15 Ground
6 5V 16 Ground
7 Ground 17 Ground
8 PW_OK 18 -5V
9 5VSB 19 5V
10 12V 20 5V
DC2: ATX Power Source Connector
The connector provides +12V to the CPU power circuit.
Pin Assignment
1 +12V
2 +12V
3 Ground
4 Ground
JATX1: AT/ATX Power Switch Header
Pin 1-2 Close: AT
Pin 2-3 Close: ATX (Default)

Chapter 2: Hardware installaon | 15
BIH11-IHP User’s Manual
JPANEL1: Front Panel Header
This connector includes Power-on, Reset, HDD LED and Power LED connecons. It allows user
to connect the PC case’s front panel switch funcons.
Pin Assignment Funcon Pin Assignment Funcon
1N/A N/A 2Power LED (+) Power
LED
3 HDD_LED (+) HDD LED 4
5HDD LED (-) 6Power LED (-)
7 Ground Reset
Buon
8Power Buon Power-On
Buon
9 Reset Control 10 Ground
SPWR1/2: HDD Power Connector
Pin Assignment
1 +5V
2 Ground
3 Ground
4 12V
JDIO1: Digital I/O Connector
This connector oers digital I/O funcons and address is set in BIOS.
Pin Assignment
1 VCC3_3
2 DI01
3 DO01
4 DI02
5 DO02
6 DI03
7 DO03
8 DI04
9 DO04
10 Ground

16 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
TPM1: Trusted Plaorm Module Header (SLB9665)
This header allows you to store cryptographic keys that protect informaon.
Pin Assignment Pin Assignment
1 LAD0 2 VCC3_3
3 LAD1 4 VCC3_3
5 LAD2 6 PCLK_TPM
7 LAD3 8 Ground
9 L_FRAME_N 10 NA
11 SER_IRQ 12 TPM_RST
13 CLK_RUN# 14 +3V3_DUAL
SATA1/2/3: Serial ATA 3.0 Gb/s Connectors (1*7 Pin)
The connector supports the thin Serial ATA cable for primary internal storage devices.
Pin Assignment
1 Ground
2 TX+
3TX-
4 Ground
5RX-
6 RX+
7 Ground
JFRONT_USB3_1: Header for USB 3.1(Gen1) Ports at Front Panel
This header allows user to add addional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment Pin Assignment
1 POWER 11 D2+
2SSRX1- 12 D2-
3 SSRX1+ 13 Ground
4 Ground 14 SSTX2+
5SSTX- 15 SSTX2-
6 SSTX+ 16 Ground
7 Ground 17 SSRX2+
8D1- 18 SSRX2-
9 D1+ 19 POWER
10 ID 20 NC

Chapter 2: Hardware installaon | 17
BIH11-IHP User’s Manual
F_USB1: Header for USB 2.0 Header
The mainboard provides USB 2.0 pin header. Each header allows you to connect 2 addional
USB 2.0 ports.
Pin Assignment Pin Assignment
1Power 2Power
3USB1 - 4USB2 -
5 USB1 + 6 USB2 +
7 Ground 8 Ground
9 X 10 NC
F_USB2: Header for USB 2.0 Header
This header allows user to add addional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment
1 +5V
2USB -
3 USB +
4 Ground
AUD1/2: Audio Connector
Pin Assignment
1 SPKRP/SPKLP
2 SPKRN/SPKLN

18 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
JSEL1/JSEL2: RS-232/422/485 Switch Headers for COM1
The headers determine that COM1 belongs to RS-232 (Default), 422, or 485.
JSEL1(JCOM1)
1-2 (Default) RS-232
3-4 RS-422
5-6 RS-485
JSEL2(JCOM1)
RS-232 RS-422 RS-485
1-3 (Default) 3-5 3-5
2-4 (Default) 4-6 4-6
7-9 (Default) 9-11 9-11
8-10 (Default) 10-12 10-12
COM2/3/4/5/6: Serial Port Headers
Pin Assignment Pin Assignment
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7RTS 8CTS
9 RI 10 NC
JPC1/2/3/4/5: Serial Port Voltage Switch Jumper for JCOM2/3/4/5/6
Pin 1-2 Close: Pin9=5V
Pin 3-4 Close: Pin9=RI (Default)
Pin 5-6 Close: Pin9=12V

Chapter 2: Hardware installaon | 19
BIH11-IHP User’s Manual
JC1: LCD Backlight Inverter Connector
This connector is for connecng to LCD for providing backlight control funcon.
Pin Assignment
1 BL_POWER
2 BL_POWER
3 BL_EN
4 BL_CTL
5 Ground
6 Ground
JLV1: LCD Panel Power Select Jumper
This jumper is for selecng LCD Power.
Pin 1-2 Close: 3.3V (Default)
Pin 2-3 Close: 5V
JLV2: LCD Backlight Inverter Power Select Jumper
This jumper is for selecng LCD Backlight Inverter Power.
Pin 1-2 Close: Inverter Power=5V
Pin 2-3 Close: Inverter Power=12V (Default)
JLVDS: LVDS for Backlight Mode Select Header
Pin 1-2 Close: 3.3V
Pin 2-3 Close: GND (Default)

20 | Chapter 2: Hardware installaon
BIH11-IHP User’s Manual
LVDS-OUT1: LVDS Connector
This connector supports 18/24 bit single-channel panels.
Pin Assignment Pin Assignment
2PVDD2, 3.3V*/5V (selected
by JLV1) 1 LVDSB_DATA0_N
4PVDD2, 3.3V*/5V (selected
by JLV1) 3 LVDSB_DATA0_P
6 Ground 5 Ground
8 Ground 7 LVDSB_DATA1_N
10 LVDSA_DATA0_N 9 LVDSB_DATA1_P
12 LVDSA_DATA0_P 11 Ground
14 Ground 13 LVDSB_DATA2_N
16 LVDSA_DATA1_N 15 LVDSB_DATA2_P
18 LVDSA_DATA1_P 17 Ground
20 Ground 19 LVDSB_CLK_N
22 LVDSA_DATA2_N 21 LVDSB_CLK_P
24 LVDSA_DATA2_P 23 Ground
26 Ground 25 LVDSB_DATA3_N
28 LVDSA_CLK_N 27 LVDSB_DATA3_P
30 LVDSA_CLK_P 29 VCC5
32 Ground 31 LVDSA_EDID_SCL
34 LVDSA_DATA3_N 33 VCC3_3
36 LVDSA_DATA3_P 35 SEL88
38 Ground 37 PVDD2
40 LVDS_EDID_SDA 39 PVDD2
JVGA1: VGA Connector
This signal of internal VGA header shares with IO VGA connector. When it is in use, you can not
use the IO VGA connector.
Pin Assignment Pin Assignment
2 5V 1 RED
4 Ground 3 GREEN
6 NC 5 NC
8DDA 7 NC
10 HSYNC 9 Ground
12 VSYSNC 11 Ground
14 DDCLK 13 Ground
16 NC 15 Ground
PE1: mSATA Slot